DynaLock E Binder 5500 Series Installation Instructions 5500IN
User Manual: DynaLock 5500 Series Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
MODEL #5500 POWER SUPPLY DynaLock 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 DynaLock 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 INSTALLATION INSTRUCTIONS MODEL #5500 POWER SUPPLY INSTALLATION INSTRUCTIONS C TYPICAL APPLICATION 5500 POWER SUPPLY BOARD B A 120 VAC 50/60 HZ INPUT A B C D E Normally-closed dry contact from Fire Alarm Control panel (By others). Fail Safe locking device. Fail Secure locking Normally closed access/egress controls. Normally open access/egress controls. 5500 Enclosure C E Enclosure Options: A A D B B C -KLC, (Key Lock Cover) -FACMR, (FAC Manual Reset) -ATS, (Anti-Tamper Switch) 12/24V Selection Switch Note: ATS Wiring on Page 3. TROUBLESHOOTING Primary Fuse 1 Amp Slow Blow 115 VAC Input Output Power Switchable from 12VDC @ 3 amps. 24VDC @ 2 amps. DB-5 & DB- 10 (Distribution Board) Option connection. PC (Power Cord) Option Prewired 6’ long Access control legal release 12V BBU1-4 or BBU1-7 ELECTROMAGNETIC LOCK No Output Power @ A 1 2 3 4 Check input line power. Check line fuse. Check F2 & F3 output fuses. Check FAC (If applicable) terminals 1 & 2 must be wired to N/C contact. Output Fuses 5 Amp slow blow No Output @ B 5 6 7 8 9 5500 Manual 24V BBU2-7 or BBU2-7 Note: Start at ‘No Output Power @ A Check jumper settings on CM/CMTD module(If applicable). Check jumper setting on DB-5/DB-10 card. Check for proper access switch contact status. Check load & external wiring for short condition. Reset Power Supply (With no load) by disconnecting input power at 1 for 2 minutes. Page #4 03/03 BBU (Battery Back-Up) Option 5500 Manual FAC Option FAC Jumper Cut if FAC Module is installed in field 03/03 MODEL #5500 POWER SUPPLY DynaLock 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 Kills all voltage outputs when interfaced with emergency system dry contact. LINE 120 VAC 50/60 HZ INPUT NEUT GND 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 INSTALLATION INSTRUCTIONS Typical Application FAC Option (Fire Alarm Control) DynaLock MODEL #5500 POWER SUPPLY INSTALLATION INSTRUCTIONS CMTD Option (Control Module with Time Delay) FACMR Option (FAC Manual Reset) LINE FAC POWER INPUT MODULE OUTPUT e A Access Control Input, Dry Contacts Only. B SPDT Dry Contacts Rated 2A @ 24V. Same as CM Option with Relock Time Delay Reset Button A Normally-Closed Dry Contact from Fire Alarm Control Panel (By others). Cut Main Board Jumper when field installed. Refer to Page #1 (FAC Jumper). Module supplied with jumper on terminals 1 & 2 as shown. DB-5 & DB-10 Option (Distribution Board) Two size distribution boards (5 or 10 position) are available to provide individually fused output terminals for each lock zone. B Adjustable for 1-80 Second delay on relock time. Opening normally closed contact removes all output power until the normally open reset button is momentarily pressed. ILB Option (Interlock Logic Board) DC Input from Power Supply Main Board Provides Four DPDT Relay Outputs Connector for CM/CMTD Modules OUTPUT JUMPERS 1 2 *Resettable Fuse ATS Option (Anti-Tamper Switch) Common Negative Terminal Positive Inputs to Energize Relay Coils Contact held open with Enclosure cover closed. White Note: Separate ILB user manual shows typical wiring diagrams. White Contact closed with Enclosure cover open. 3 White White Without Control Module Option NOTE: ATS switch contacts rated .25A @ 24V. *Resetting is done by first correcting the overload then disconnecting the load or turning off the line voltage for two minutes. With Control Module Option (Factory Setting) CM Option (Control Module) A Accepts access/egress control dry contact input. Provides SPDT relay output. Access Control Input, Dry Contacts Only. B SPDT Dry Contacts Rated 2A @ 24V. A B Installation Information Single Full Size LOCK CAPACITY CHART Double Full Single Double Size Single Delay Egress Deadbolt 12VDC 6 3 6 3 3 3 24VDC 8 4 8 4 3 4 12 AWG 10 AWG CURRENT DRAW UP TO 1/2 AMP Voltage 20 AWG 18 AWG 16 AWG 14 AWG 12VDC 50Ft. 100Ft. 150Ft. 250Ft. 400Ft. 750Ft. 24VDC 100Ft. 200Ft. 300Ft. 500Ft. 750Ft. 1500Ft. *This chart indicatess minimum recommended wire size, but local codes prevail 5500 Manual Page #2 03/03 5500 Manual Page #3 03/03 MODEL #5500 POWER SUPPLY DynaLock 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 Kills all voltage outputs when interfaced with emergency system dry contact. LINE 120 VAC 50/60 HZ INPUT NEUT GND 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 INSTALLATION INSTRUCTIONS Typical Application FAC Option (Fire Alarm Control) DynaLock MODEL #5500 POWER SUPPLY INSTALLATION INSTRUCTIONS CMTD Option (Control Module with Time Delay) FACMR Option (FAC Manual Reset) LINE FAC POWER INPUT MODULE OUTPUT e A Access Control Input, Dry Contacts Only. B SPDT Dry Contacts Rated 2A @ 24V. Same as CM Option with Relock Time Delay Reset Button A Normally-Closed Dry Contact from Fire Alarm Control Panel (By others). Cut Main Board Jumper when field installed. Refer to Page #1 (FAC Jumper). Module supplied with jumper on terminals 1 & 2 as shown. DB-5 & DB-10 Option (Distribution Board) Two size distribution boards (5 or 10 position) are available to provide individually fused output terminals for each lock zone. B Adjustable for 1-80 Second delay on relock time. Opening normally closed contact removes all output power until the normally open reset button is momentarily pressed. ILB Option (Interlock Logic Board) DC Input from Power Supply Main Board Provides Four DPDT Relay Outputs Connector for CM/CMTD Modules OUTPUT JUMPERS 1 2 *Resettable Fuse ATS Option (Anti-Tamper Switch) Common Negative Terminal Positive Inputs to Energize Relay Coils Contact held open with Enclosure cover closed. White Note: Separate ILB user manual shows typical wiring diagrams. White Contact closed with Enclosure cover open. 3 White White Without Control Module Option NOTE: ATS switch contacts rated .25A @ 24V. *Resetting is done by first correcting the overload then disconnecting the load or turning off the line voltage for two minutes. With Control Module Option (Factory Setting) CM Option (Control Module) A Accepts access/egress control dry contact input. Provides SPDT relay output. Access Control Input, Dry Contacts Only. B SPDT Dry Contacts Rated 2A @ 24V. A B Installation Information Single Full Size LOCK CAPACITY CHART Double Full Single Double Size Single Delay Egress Deadbolt 12VDC 6 3 6 3 3 3 24VDC 8 4 8 4 3 4 12 AWG 10 AWG CURRENT DRAW UP TO 1/2 AMP Voltage 20 AWG 18 AWG 16 AWG 14 AWG 12VDC 50Ft. 100Ft. 150Ft. 250Ft. 400Ft. 750Ft. 24VDC 100Ft. 200Ft. 300Ft. 500Ft. 750Ft. 1500Ft. *This chart indicatess minimum recommended wire size, but local codes prevail 5500 Manual Page #2 03/03 5500 Manual Page #3 03/03 MODEL #5500 POWER SUPPLY DynaLock 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 DynaLock 705 Emmett Street Bristol, CT 06011-2728 Phone:(860) 582-4761 Fax:(860) 585-0338 INSTALLATION INSTRUCTIONS MODEL #5500 POWER SUPPLY INSTALLATION INSTRUCTIONS C TYPICAL APPLICATION 5500 POWER SUPPLY BOARD B A 120 VAC 50/60 HZ INPUT A B C D E Normally-closed dry contact from Fire Alarm Control panel (By others). Fail Safe locking device. Fail Secure locking Normally closed access/egress controls. Normally open access/egress controls. 5500 Enclosure C E Enclosure Options: A A D B B C -KLC, (Key Lock Cover) -FACMR, (FAC Manual Reset) -ATS, (Anti-Tamper Switch) 12/24V Selection Switch Note: ATS Wiring on Page 3. TROUBLESHOOTING Primary Fuse 1 Amp Slow Blow 115 VAC Input Output Power Switchable from 12VDC @ 3 amps. 24VDC @ 2 amps. DB-5 & DB- 10 (Distribution Board) Option connection. PC (Power Cord) Option Prewired 6’ long Access control legal release 12V BBU1-4 or BBU1-7 ELECTROMAGNETIC LOCK No Output Power @ A 1 2 3 4 Check input line power. Check line fuse. Check F2 & F3 output fuses. Check FAC (If applicable) terminals 1 & 2 must be wired to N/C contact. Output Fuses 5 Amp slow blow No Output @ B 5 6 7 8 9 5500 Manual 24V BBU2-7 or BBU2-7 Note: Start at ‘No Output Power @ A Check jumper settings on CM/CMTD module(If applicable). Check jumper setting on DB-5/DB-10 card. Check for proper access switch contact status. Check load & external wiring for short condition. Reset Power Supply (With no load) by disconnecting input power at 1 for 2 minutes. Page #4 03/03 BBU (Battery Back-Up) Option 5500 Manual FAC Option FAC Jumper Cut if FAC Module is installed in field 03/03
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2006:06:28 12:22:56-04:00 Create Date : 2006:06:28 12:22:34-04:00 Metadata Date : 2006:06:28 12:22:56-04:00 Creator Tool : PageMaker 6.5 Format : application/pdf Title : DynaLock E-Binder Description : Version 6.02 Creator : Mike & JohnJr Document ID : uuid:78f5b4c8-71eb-4325-b4f3-a4c09368db96 Instance ID : uuid:acf4e2a0-8b09-4a82-8f62-aa3f6e3479aa Producer : Acrobat Distiller 6.0 (Windows) Has XFA : No Page Count : 4 Subject : Version 6.02 Author : Mike & JohnJrEXIF Metadata provided by EXIF.tools