Dynabook UPA3426WL 802.11 b/g Half Size Mini-PCI WLAN Module User Manual Palao WLAG 1106 03

Download:
Mirror Download [FCC.gov]
Document ID	519120
Application ID	zlFToz1Fwttx1KvpfMtC/g==
Document Description	Instalation
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	47.45kB (593176 bits)
Date Submitted	2005-03-01 00:00:00
Date Available	2005-04-14 00:00:00
Creation Date	2003-12-01 10:42:40
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-02-08 14:25:44
Document Title	Palao_WLAG_1106_03
Document Creator	Adobe PageMaker 7.0
Document Author:	okano

TOSHIBA Wireless LAN Card
Installation
This sheet provides information on installing the Wireless LAN card in the PORTÉGÉ
M200.
CAUTION: This sheet is for information only. The Wireless LAN card must
be installed by dealers of TOSHIBA or TOSHIBA OEM products.
NOTE: The Wireless LAN card is a wireless network card that complies
with the IEEE 802.11 standard for Wireless LANs (Revision B.)
Installing the Wireless LAN card
1. Discharge static electricity from your body by touching a metal object, before
you handle the card.
2. Turn off the power and disconnect the AC adaptor.
3. Lay the computer upside down.
4. Remove the battery pack from the computer. For instructions on removing the
battery pack, refer to Chapter 6 in the online manual.
5. Remove twenty screws securing computer’s under cover. (One screw is situated
under the battery pack.)
NOTE: Use a point size 0 Phillips screwdriver.
Figure 1 Removing twenty screws
6. Loosen one screw securing the memory module cover and lift off the cover.
Remove the memory module. Refer to Chapter 8 in the online manual for details.
7. Loosen one screw securing the HDD cover and lift off the cover.
Figure 2 Removing the memory module cover and HDD cover
8. Slide the HDD and remove it.
Figure 3 Removing the HDD
9. Disconnect the VGA fan cable under the memory module.
Figure 4 Removing the VGA fan cable
10. Remove the computer’s under cover.
Figure 5 Removing the computer’s under cover
11. Remove flat-head two screws and the metal cover.
Figure 6 Removing two screws and the metal cover
12. Connect the antenna cables to the proper connectors on the Wireless LAN card.
The cables are color coded white and black. Refer to figure 7 to see for which
color to goes to which connector.
CAUTION: Be careful not to apply pressure to the ICs on the Wireless LAN
card.
13. Hold the card at about a 45 degree angle, fit it into the computer’s connector and
press carefully to ensure firm contact.
14. Gently, push the card down until latches on either side engage the card to hold it
in place.
BLACK
WHITE
Figure 7 Installing the Wireless LAN card
15. Route the cable as shown below and secure it with tape.
Figure 8 Routing the Wireless LAN cable
16. Seat the metal cover on the Wireless LAN card and secure it with flat-head two
screws.
17. Seat the computer’s under cover.
18. Connect the VGA fan cable under the memory module.
19. Seat the memory module. Refer to Chapter 8 in the online manual for details.
20. Seat the memory module cover and secure it with one screw.
21. Install the HDD.
22. Seat the HDD cover and secure it with one screw.
23. Secure twenty screws.
24. Turn the computer upside down.
Applying labels
The figure below shows the locations of labels . The letters A, B, C and D correspond
to labels identified in later illustrations. The applied labels will vary according to your
computer’s configuration.
Figure 9 Label positions
5.
Apply the following Singapore Regulatory label to position D. If your computer
already has the Singapore Regulatory label, you do not need to apply a new label.
Figure 13 Singapore Regulatory label

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2003:12:01 10:42:40+09:00
Modify Date                     : 2005:02:08 14:25:44+09:00
Subject                         : Palao_WLAG_1106_03
Page Count                      : 8
Creation Date                   : 2003:12:01 10:42:40+09:00
Mod Date                        : 2005:02:08 14:25:44+09:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : okano
Keywords                        : 
Metadata Date                   : 2005:02:08 14:25:44+09:00
Creator                         : okano
Title                           : Palao_WLAG_1106_03
Description                     : Palao_WLAG_1106_03
Has XFA                         : No

EXIF Metadata provided by EXIF.tools