Dynabook UPA3674RF Wireless Presenter User Manual presenter
Toshiba Corporation Wireless Presenter presenter
Dynabook >
Manual
User’s Manual
Wireless Presenter
Introduction
Thank you for purchasing the Toshiba Wireless Presenter. The
Wireless Presenter with Laser Pointer enables you to control your
onscreen presentations within a range of 50 feet, making it perfect
for large conference rooms. The presenter supports the most
common PowerPoint® presentation functions including Page Up,
Page Down, and Darken Screen & Resume Screen. It also has a
laser pointer to help you focus in on key messages. The small size
allows you to control your presentation with ease and enjoy
freedom of movement as you present. Just plug and play, no
software is required.
Package Contents
❖Wireless Presenter with receiver unit
❖User’s Manual
❖Warranty booklet
❖AAA Battery (1)
Minimum System Requirements
❖USB port
❖Windows® Vista™ /XP/2000
This is a Class 2 Laser product. Please DO NOT look at or
direct the laser beam at anyone’s eye.
Functions and Features:
2
Functions and Features:
Top Side
Back Side
- Page Up - Auto on/off function
- Page Down - Self contained receiver unit
- Darken Screen - Low battery warning light
- Resume Screen - Up to 50 foot range
- Laser Pointer - Compact for travel
Laser Button: Laser Pointer On/Off
Right Button: Page Down
Pause Button: Darken & Resume Screen
Left Button: Page Up
Reset Button
Battery Cover
Receiver Unit
Low power LED (
flashes orange when battery is low)
Receiver Unit 3
Receiver Unit
Getting Started
Inserting the Battery
Open the battery cover and insert 1 AAA battery.
Follow the same procedure as outlined above when replacing the
battery.
Removing the Receiver
To remove the receiver unit from its compartment, pull up on
the small nub on the back of the receiver. The Presenter will
power on immediately after removing the receiver unit.
USB Plug
LED
Reset Button
Connecting the Receiver
4
Connecting the Receiver
Insert the USB receiver into an available USB port on your
computer. Connection to the presenter is automatic.
Switching Channels (if necessary)
This is a plug-and-play device. Normally, it is not necessary
to set the RF channel. If you should experience interference,
please follow the steps below to select a new RF channel:
1.Plug the receiver unit into one of the USB ports on the
computer and press and release the reset button.
2. Within 10 seconds, press and release the reset button on the
back of the presenter.
Press
Press
Storing the Receiver Unit 5
Storing the Receiver Unit
Replace the receiver unit into the compartment in the back the
presenter.
With the small nub pointing up, slide the USB end of the
receiver unit into the compartment and press down gently until
the receiver clicks into place.
The Presenter will power off after putting the receiver into its
compartment.
Troubleshooting
If the Presenter stops working, please try one of the following:
❖ Make sure the presenter is within 50 feet of the receiver.
❖ Press the reset buttons of the receiver and presenter for
switching channels.
❖ Turn off any wireless devices that are near the presenter’s
receiver.
❖ Replace the battery.
Regulatory statements
6
Regulatory statements
FCC Information
Product Name: Wireless Presenter
Model number: PA3674U-1ETB
FCC notice "Declaration of Conformity
Information"
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
WARNING: Changes or modifications made to this equipment, not
expressly approved by TOSHIBA or parties authorized by TOSHIBA
could void the user’s authority to operate the equipment.
IC Information 7
FCC Conditions
This equipment has been tested and found to comply with Part
15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
Contact
IC Information
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of this
device.
L'utilisation de ce dispositif est soumis aux deux
conditions suivantes: (1) il ne doit pas produire de
brouillage et (2) l'utilisateur du dispositif doit être prêt à
accepter tout brouillage radioélectrique reçu, même s'il
est susceptible de compromettre son fonctionnement.
The term “IC” before the equipment certification
number only signifies that the Industry Canada technical
specifications were met.
Address: TOSHIBA America Information
Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone: (949) 583-3000
Specifications
Wireless Presenter
Presenter
Receiver unit
Button: Left: Page up
Right: Page down
Top: Laser Pointer
Bottom: Darken Screen/Resume Screen
Dimension (D x W x H): 115 x 30 x 23 mm
4.5 x 1.2 x 0.9 inches
Weight: 35g (1.2 ounces)
Battery Type: 1.5V, AAA x 1
Interface: RF 2.4GHz
RF Output Power: 0dbm (1mW)
Operation range: Approximately 15 meter (50 feet)
Laser Wavelength: 650nm
Laser power: 0.6 ~ 0.9 mW
Power consumption: Pairing: 3V, 26 mA
Buttons: 3V, 2 ~ 4 mA
Static: 3V, 24 uA
Laser: 3V, 24 mA
Working temperature: 5°C(41°F) to 35°C(95°F)
Interface: USB, RF 2.4GHz
Dimension (D x W x H): 48 x 16 x 9 mm
1.9 x 0.6 x 0.4 inches
Weight: 5.8g (0.2 ounces)
Working Temperature: 5°C(41°F) to 35°C(95°F)