E TECH IM100 Private Land Mobile Radio for Vehicle (VHF) User Manual IM100 users manual
E-TECH Co., Ltd. Private Land Mobile Radio for Vehicle (VHF) IM100 users manual
E TECH >
Contents
- 1. User Manual Part 1
- 2. User Manual Part 2
User Manual Part 2
E-TECH Co., Ltd 1/19 ▶ User’s Manual◀ 1. Introduction 2. Description of Unit 3. Technical Specification 4. Features and Operation 5. Antenna Installation FILE: IM 100 service manual.doc 2004.11.23 192 E-TECH Co., Ltd 2/19 - 2 -219 1. Introduction IM100 has a compact size with a various features in the range of 136~174MHz. IM100 Has a various features shown as below. IM100 constructed with a microprocessor controlled, temperature compensated Phase Locked Loop(PLL) frequency synthesizer. The radio features a double conversion receiver and a direct FM transmitter modulator. A special integrated circuit provides support to sub-audible signaling(CTCSS & DCS) and most of the receiving parts are switched off periodically in the power save mode to reduce battery current drain during standby. 2. Description of Unit Items Model Radio IM100 Supplied Package User manual Items Model Hand Microphone Accessories VOX & PTT Headset Power Cable Pedestal FILE: IM100 manual.doc 2004.11.23 193 E-TECH Co., Ltd 3/19 - 3 -319 3. Technical Specifications 3-1 General 1) Frequency range 136~174 MHz 2) Channels 255 Channels 3) Channel spacing 12.5 kHz/25 kHz 4) Communication method Simplex 5) Antenna Impedance 50 ohm 6) Power supply voltage DC 13.6V 7) Current Drain 8) Microphone When Transmitting(50W) < 13A When Receiving(5W) < 1A Transmit standby < 100mA External Condenser Mic 9) Operating temperature range: -30℃ ∼ +60℃ 10) Size 178(W)x49(H)x195(D) 11) 1600g Weight 3-2 Transmitter 1) Power Output HIGH – 50W, LOW - 5W 2) Modulation 8K50F3E/16K0F3E 3) Oscillator method PLL 4) Frequency Stability less than ±0.00025% (±2.5PPM) 5) Maximum frequency deviation: ±2.5 kHz(Narrow)/ ±5 kHz(Wide) 6) Audio Distortion less than 5% (1 kHz 60%) 7) SPURIOUS Emission -70 [dBc] 8) FM Hum & Noise -40 / -45 [dB] (HP8920A 300Hz ∼ 3kHz BPF) 9) BAND 38 [MHz] SPREAD FILE: IM100 manual.doc 2004.11.23 194 E-TECH Co., Ltd 4/19 - 4 -419 3-3 Receiver 1) Receiver Type Double Super Hetero type 2) Sensitivity -0.25uV 이하(12dB SINAD 시) 3) Frequency Stability ±0.00025%(±2.5PPM) 4) SPURIOUS Rejection : -75 dB 5) Adjacent Channel Selectivity: -65 dB (Narrow) , -70 dB (Wide) 6) Distortion 5% (1 kHz 60%) 7) Hum & Noise -40 / -45 dB(HP8920A 300Hz ∼ 3kHz BPF) 8) Audio output Normal 3W ( Max 5W ) 9) BAND SPREAD 38MHz 10) Speaker size 48 * 30 Rectangle 4. Features and Operation EXTERNAL VIEW 14)LCD 11)POWER ON/OFF &Volume control 13)Ear/Mic Jack PC-Programming Jack 9) LED I 1)TX POWER HIGH/LOW 2)Monitor Button 14)SPEAKER 8)Squelch 6)Menu Button 3)UP button FILE: IM100 manual.doc 3)DOWN button 4)Emergency Key 2004.11.23 195 E-TECH Co., Ltd - 5 -519 5/19 4-1 Features & Operation 1. Monitor Press the Monitor key momentarily to disable the Tone squelch. 2. Radio Call By using Various 5Tone, individual / Group call is available. 16 Receiving codes are available as well as open call. 3. Missed calls list 16 Missed calls can be listed. If a call remains unanswered, the call will be stored by the radio. 4. contact list During a call, the contact list may be used to give access to up to 16 preprogrammed numbers accessed via the menu. 5. status list A status is a code for transmitting prearranged messages, e.g. status “05” may indicate “launch”. Status list contains up to 30 entries. 6. Channel : 255 channel 7. Scan ON/off 8. Power level : Power level is adjustable in each channel respectively. 9. Talkaround on/off 10. Emergency : 11. Lone Worker 12. Tx Tone select : In the menu, tx dcs /ctcss tone is adjustable. 13. Rx Tone select : In the menu, rx dcs /ctcss tone is adjustable. 14. Group : Defines group tone. You can select tone code for group, and it is used as a default value . 0~9 and a, b, c, d available. And “A” is used as a basic value.. 15. BEEP ON/OFF : BEEP sound ON/OFF. 16. KEY LOCK : LOCK/UNLOCK Button KEY. 17. SQUELCH : Squelch level is adjustable 18. AUTO SQUELCH : Squelch level is adjustable automatically by surroundings. 19. DTMF ON/OFF : DTMF function is available. 20. VOX : VOX LEVEL is adjustable by pushing up and down button. 21. AUTO VOX : VOX level is adjustable automatically by surroundings. 22. P - SCAN : Priority Scan 23. POWER SAVE : Power save mode is available. 24. PASS WORD : This function is useful for security reason. 25. LOCATION INDICATE : Indicate where the radio is located by blinking green light every 7 seconds. 26. SCRMABLE : Internal Voice Scrambler is available. 27. STUN / UNSTUN : For added security and to avoid abuse of the radio system in which you operate a feature known as Stun/Unstun is included in your radio. 28. BACKLIGHT : Lamp is lighting when you check LCD status. FILE: IM100 manual.doc 2004.11.23 196 E-TECH Co., Ltd 6/19 - 6 -619 4-2 LCD Display and Icons 1.ANT GAZE ; Shows the received signal strength. 2.TX POWER HIGH: Indicate power level 3.KEY LOCK: Appears during key lock function is ON. 4.ALART(BEEP) ON/OFF: Appears when beep sound is turned ON. 5.Battery level indicator: Indicates reaming battery power. 6.VOX ON/OFF: Appears when VOX function is turned On. 7.SCAN: Appears when Scan function is activated. 8.SCRAMBLE: Appears while the voice scrambler function is activated. 9.TALK AROUND Indicator. 4-3 Features 1. Channel This radio offers up to 255 channels 1). By using or button, you can select the desired channel. 2. Missed calls list Up to 16 calls can be stored. If the same radio calls more than once, only the most recent call is stored. When fifteen calls have been stored by the radio, depending on the radio programming the sixteenth call received may overwrite the first or not be stored by the radio. 1). to enter Menu Mode. 2) Display shows 3) to select 4) or 5) to exit FILE: IM100 manual.doc to scroll list 2004.11.23 197 E-TECH Co., Ltd - 7 -719 7/19 3. Contact list 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to exit to until to scroll list 4. Status call list 4-1. Making STATUS call 1) to enter Menu Mode. 2) or 3) to select 4) or to until to scroll list 5) Push PTT KEY for sending message on the LCD. 4-2 Make STATUS Message 1) to enter Menu Mode. FILE: IM100 manual.doc 2004.11.23 198 E-TECH Co., Ltd - 8 -819 2) or 3) to select 4) or 5) 8/19 to until to scroll list to SELECT 5. Lone work 1). to enter Menu Mode. 2) or 3) to select 4) or to until to select ON/OFF 6. Tx power .1). to enter Menu Mode. 2) or 3) to select 4) or FILE: IM100 manual.doc to until to select HIGH / LOW POWER 2004.11.23 199 E-TECH Co., Ltd 5) - 9 -919 9/19 to select 7. Tx Tone Selecting Transmitting TONE(CTCSS/DCS). 1). to enter Menu Mode. 2) or 3) to select 4) or to until to Select TONE을 either CTCSS or DCS. 0= NON TONE 1-38 CTCSS 101 – 183 DCS TONE 5) to select exit 8. Rx Tone Changing Receiving TONE(CTCSS/DCS). 1). to enter Menu Mode. 2) or 3) to select 4) or to until to select TONE either CTCSS or DCS. 0= NON TONE 1-38 CTCSS 101 – 183 DCS TONE. FILE: IM100 manual.doc 2004.11.23 1910 E-TECH Co., Ltd 5) - 10 -1019 10/19 to select exit 9. Group Changing GROUP Tone. 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to until to select scroll list to select exit 10. Beep on/off 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to select on off . 11. Key lock 1). to enter Menu Mode. FILE: IM100 manual.doc 2004.11.23 1911 E-TECH Co., Ltd - 11 -1119 2) or 3) to select 4) or 5) to select 11/19 to until to select key lock /unlock. 12. Squelch level 16 level is available. 0 = terminate sq function 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to until to the scroll list to select exit 13. Auto Squelch 1). to enter Menu Mode. 2) or 3) to select FILE: IM100 manual.doc to until 2004.11.23 1912 E-TECH Co., Ltd - 12 -1219 4) or 5) to select to 12/19 select on /off . 14. Scan 1). to enter Menu Mode. 2) or 3) to scan. to until 4) Push PTT for exit 15. DTMF 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to select ON /OFF. 16. Vox on/off 1). 2) to enter Menu Mode. or FILE: IM100 manual.doc to until 2004.11.23 1913 E-TECH Co., Ltd - 13 -1319 3) to select 4) or 5) to select to 13/19 select ON /OFF. 17. Vox Level 16 level is available.. 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to scroll list for exit 18. Auto Vox 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select FILE: IM100 manual.doc to until to select ON /OFF. 2004.11.23 1914 E-TECH Co., Ltd - 14 -1419 14/19 19. Priority Scan 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to select ON /OFF. 20. Priority scan CH 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to until to scroll list to select for exit 21. Power save 1). 2) to enter Menu Mode. or FILE: IM100 manual.doc to until 2004.11.23 1915 E-TECH Co., Ltd - 15 -1519 3) to select 4) or 5) to select to 15/19 select ON /OFF. 22. Talkaround 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to select ON /OFF. 23. Password 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select FILE: IM100 manual.doc to until to select ON /OFF. 2004.11.23 1916 E-TECH Co., Ltd - 16 -1619 16/19 24. Password CH 1). to enter Menu Mode. 2) or 3) to select to until 4) ---- will display on the LCD( enter old password) or by pushing up and down KEY to change password. by pushing enter KEY to change digit of password. 5) Enter new password by 4 digit. 25. Location Indicate where the radio is located by blinking green light every 7 seconds. 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to select ON /OFF. 26. Scramble 1). 2) to enter Menu Mode. or FILE: IM100 manual.doc to until 2004.11.23 1917 E-TECH Co., Ltd 17/19 - 17 -1719 3) to select 4) or 5) to select to select ON /OFF. 27. Status call Send 1). to enter Menu Mode. 2) or 3) to select 4) or 5) to select to until to select ON /OFF. 5. Antenna Installation 5-1 Antenna Installation and Compliance with Radio Frequency(RF) Energy Safety Standards [IMPORTANT NOTE] To assure optimum performance and compliance with RF Energy Safety standards, this antenna installation guidelines and Instructions are limited to metal-body vehicles with appropriate ground planes and take into account the potential exposure of backseat passengers and bystanders outside the vehicle. [NOTE] For mobile radios with rated power of 7 watts or less, the only installation restrictions are to use only E-tech approved antennas and install the antenna externally on metal body vehicles. For mobile radios with rated power greater than 7 watts, always adhere to all the guidelines and restrictions in 5.2 below. FILE: IM100 manual.doc 2004.11.23 1918 E-TECH Co., Ltd 18/19 - 18 -1819 5-2 Selecting an Antenna Site/Location on a Metal Body Vehicle 1. External installation – Check the requirements of the antenna supplier and install the vehicle antenna external to a metal body vehicle in accordance with those requirements. 2. Roof top – For optimum performance and compliance with RF Energy Safety standards, mount the antenna in the center area of the roof. 3. Trunk lid – On some vehicles with clearly defined, flat trunk lids, the antenna of some radio models (see restrictions below) can also be mounted on the center area of the trunk lid. For vehicles without clearly defined, flat trunk lids (such as hatchback autos, sport utility vehicles, and pick-up trucks), mount the antenna in the center area of the roof. Before installing an antenna on the trunk lid. • Be sure that the distance from the antenna location on the trunk lid will be at least 60cm (24 inches) from the front surface of the rear seat-back to assure compliance with RF Energy Safety standards. • Ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassis. If these conditions can not be satisfied, then mount the antenna on the roof top ! 4. Mounting restrictions for certain radio models For more than 40 Watt VHF models, the 1/4 wave antenna should be mounted only in the center area of the roof, not on the trunk lid, to assure compliance with RF Energy Safety standards. 5. Ensure that the antenna cable can be easily routed to the radio. Route the antenna cable as far away as possible from any vehicle electronic control units and associated wiring. 6. Check the antenna location for any electrical interference. 7. Make sure any other mobile radio antenna on this vehicle is at least 30.48 cm (1 foot) away from this antenna. [NOTE] Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, etc.) in close proximity to the antenna can cause severe receiver interference. FILE: IM100 manual.doc 2004.11.23 1919 E-TECH Co., Ltd 19/19 - 19 -1919 5-3 Antenna Installation Procedure 1. Mount the antenna according to the instructions provided with the antenna kit. cable to the radio mounting location. Run the coaxial If necessary, cut off the excess cable and install the cable connector. 2. Connect the antenna cable connector to the radio antenna connector on the rear of the radio. 5-4 Completing the Installation 1. Mount the microphone clip to a convenient spot near your radio. 2. Your microphone has a telephone-type connector at the end of is cord. Plug the microphone into the control head connector. 3. To complete your radio installation, plug the power cable into the radio power connector. FILE: IM100 manual.doc 2004.11.23
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 19 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:1d756f54-0547-4315-a235-4f4ae0033285 Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2004:12:23 20:55:10+09:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2004:12:23 20:55:10+09:00 Document ID : uuid:9efe2950-33b6-4c6d-b02d-f38c8d4bc231 Format : application/pdf Title : Microsoft Word - IM100_users manual.doc Creator : erwin_ryu Author : erwin_ryuEXIF Metadata provided by EXIF.tools