E TECS ET-DC01 2.4GHz WIRELESS H.264 DIGITAL CAMERA User Manual Camera only0423

E-TECS LIMITED 2.4GHz WIRELESS H.264 DIGITAL CAMERA Camera only0423

UserManual.wiki >

E TECS >

ET DC01 User Manual HTML Version

Users Manual

2.4GHZ WIRELESS H.264 DIGITAL CAMERA

USER MANUAL

FCC Notice to Users

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the

user's authority to operate the equipment.

The antenna used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-located or operated

in conjunction with any other antenna or transmitter

CAMERA

① Only for firmware upgrade

② Camera Lens

③ RESET button

④ Mini USB connection

⑤ On/Off/PAIR button

⑥ Power and charging

status indicator LED

⑦ Microphone

⑧ Mount hole

NOTE:ON/OFF: Press and hold button for 3 to 5seconds.

PAIR:Press and quickly release button.

1.NIGHT-VISION(IR)OPERATION:

The camera is equipped with eight(8) Infrared LEDS for night-

vision operation. In low light situation the Infrared LEDS turn-on

automatically, to activate night-vision.

NOTE: The night-vision picture is always black & white and not

that sharp. This camera has up to 10 feet night-vision range.

2. USING CAMERA STAND/MOUNT

● Screw the camera the /mount and as shown

or to a wall or ceiling(screws no included).

on stand setup

screw it

3. CHARGING RECHARGEABLE BATTERY IN TRANSMITTER

(CAMERA)

The rechargeable battery supplied with the transmitter (camera)

must be fully charged before it is used for the first time on battery

power.

Warning: Only qualified technicians or our technical staff is

authorized to change the rechargeable battery in the transmitter!

NOTE:The transmitter automatically turns on and the battery

starts getting charged when AC adapter or a USB cable

connected to a computer is plugged into the MINI USB

socket .

● When the transmitter is turned o

, the flashes ,

s .

When the transmitter is turned o

● The charging time for a fully rechargeable battery when

the device is turned off is approximately 5 hours. The charging time

double if the transmitter is turned on whil the battery is ing

charged.

on the transmitter

n and the battery is getting

charged power status LED green and once the battery

is fully charged the LED become solid

ff and the battery is getting charged

the power status LED flashes red and once the battery is fully

charged the LED turn off

discharged

s e gett

4. USING THE TRANSMITTER(CAMERA)

● For optimal transmission, place the camera in the room to be

monitored in such a way as to ensure the optimal surveillance of

your baby or the elderly.

You can also mount the camera using the stand included as

described in section 2

Note:For safety reasons and for optimum sound transmission we

recommend that you keep the transmitter at least 1 meter(3 feet)

from the baby.

IMPORTANT:Never place camera in the baby's cot, bed or playpen!

NOTE:The transmitter will automatically turn on when plugged

into AC adapter or computer.

● The transmitter can be powered with the , the rech-

argeable battery, or via computer USB cable.

● To use the rechargeable battery, the device shall be turned on

without the plugged in.

● The transmitter turns on when the ON/OFF/PAIR button is pressed

for 5 seconds. As soon as the camera is powered on the LED

indicator flash green to

, ress ON/OFF/PAIR button for 5 seconds.

● When the battery voltage falls below 3.6V the Power Indicator

LED turns red from green,indicating the battery needs to be

charged.

The receiver displays "Camera battery is low"on the screen.

IMPORTANT:

(hardware to mount the stand to a wall

or ceiling not included)

AC adapter

's USB port using a

AC adapter

turns solid green or es indicate the

camera is powered on

To turn camera off p

In case of audio or video interference press and

release RESET button to switch transmitter to a different channel

5.REGISTER/PAIR CAMERA FOR WITH 2.4" SCREEN BABY MONITOR:

● Turn camera power ON

● Turn Monitor ON

Menu/OK → Main Menu → Multi Camera → Register

Camera → Camera 1 → Register Camera 1? → Yes

n transmitter/camera → On/Off

Note:Press and quickly release the ON/OFF/PAIR button on the CAMERA

to complete pairing process.

● Press"OK/MENU"button on the monitor to display Main Menu.

● Use "UP"or "DOWN"button to highlight "Multi Camera" Option and

press "OK/MENU" button to complete the selection.

● From "Multi Camera" Menu highlight "Register Camera" using "UP" or

"DOWN" button and press "OK/MENU"button to complete the selection

● From "Register Camera" Menu highlight one of the available(not used)

camera number you want to assign to this new camera and press

"OK/MENU" button to complete the selection.

NOTE:Camera numbers which have already been allocated (used to register

existing cameras) have "thumbs up" sign next to the camera number.

● Use "UP" or "DOWN" button to select "Yes" and press "OK/MENU"

button to complete the selection;the screen will display "register camera

#" where # is the camera number you selected.

● Press and quickly release ON/OFF button on the CAMERA to complete

pairing process

● If pairing is successful, the screen will display "Camera # Registered",

where # is the camera number you selected in previous step. "Thumbs

up" sign will appear next to the camera #.

NOTE:If the pairing/registration process is not successful, repeat this

process again.

● Press "ESC" button twice to exit from the Menus and view the camera.

6.REGISTER/PAIR CAMERA WITH 3.2" SCREEN BABY MONITOR: