E TECS ET-DC01 2.4GHz WIRELESS H.264 DIGITAL CAMERA User Manual Camera only0423

Download:
Mirror Download [FCC.gov]
Document ID	1542150
Application ID	YKgNm672yze5jrvIzK8SYQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.18kB (189781 bits)
Date Submitted	2011-09-15 00:00:00
Date Available	2011-09-15 00:00:00
Creation Date	2011-08-02 10:39:26
Producing Software	Corel PDF Engine Version 1.0.0.458
Document Lastmod	0000-00-00 00:00:00
Document Title	user manual-Camera only0423
Document Creator	CorelDRAW 版本 12.0

2.4GHZ WIRELESS H.264 DIGITAL CAMERA
USER MANUAL
FCC Notice to Users
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user's authority to operate the equipment.
The antenna used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operated
in conjunction with any other antenna or transmitter
01
CAMERA
① Only for firmware upgrade
② Camera Lens
③ RESET button
④ Mini USB connection
⑤ On/Off/PAIR button
⑥ Power and charging
status indicator LED
⑦ Microphone
⑧ Mount hole
NOTE:ON/OFF: Press and hold button for 3 to 5seconds.
PAIR:Press and quickly release button.
1.NIGHT-VISION(IR)OPERATION:
The camera is equipped with eight(8) Infrared LEDS for nightvision operation. In low light situation the Infrared LEDS turn-on
automatically, to activate night-vision.
NOTE: The night-vision picture is always black & white and not
that sharp. This camera has up to 10 feet night-vision range.
2. USING CAMERA STAND/MOUNT
● Screw the camera on the stand /mount and setup as shown
or screw it to a wall or ceiling(screws no included).
02
3. CHARGING RECHARGEABLE BATTERY IN TRANSMITTER
(CAMERA)
The rechargeable battery supplied with the transmitter (camera)
must be fully charged before it is used for the first time on battery
power.
Warning: Only qualified technicians or our technical staff is
authorized to change the rechargeable battery in the transmitter!
NOTE:The transmitter automatically turns on and the battery
starts getting charged when AC adapter or a USB cable
connected to a computer is plugged into the MINI USB
socket on the transmitter .
● When the transmitter is turned o n and the battery is getting
charged , the power status LED flashes green , and once the battery
is fully charged the LED become s solid .
When the transmitter is turned o ff and the battery is getting charged
the power status LED flashes red and once the battery is fully
charged the LED turn s off .
● The charging time for a fully discharged rechargeable battery when
the device is turned off is approximately 5 hours. The charging time
double s if the transmitter is turned on whil e the battery is gett ing
charged.
03
4. USING THE TRANSMITTER(CAMERA)
● For optimal transmission, place the camera in the room to be
monitored in such a way as to ensure the optimal surveillance of
your baby or the elderly.
You can also mount the camera using the stand included as
described in section 2 (hardware to mount the stand to a wall
or ceiling not included) .
Note:For safety reasons and for optimum sound transmission we
recommend that you keep the transmitter at least 1 meter(3 feet)
from the baby.
IMPORTANT:Never place camera in the baby's cot, bed or playpen!
NOTE:The transmitter will automatically turn on when plugged
into AC adapter or computer.
● The transmitter can be powered with the AC adapter, the rechargeable battery, or via computer 's USB port using a USB cable.
● To use the rechargeable battery, the device shall be turned on
without the AC adapter plugged in.
● The transmitter turns on when the ON/OFF/PAIR button is pressed
for 5 seconds. As soon as the camera is powered on the LED
indicator turns solid green or flash es green to indicate the
camera is powered on .
To turn camera off , p ress ON/OFF/PAIR button for 5 seconds.
● When the battery voltage falls below 3.6V the Power Indicator
LED turns red from green,indicating the battery needs to be
charged.
The receiver displays "Camera battery is low"on the screen.
IMPORTANT: In case of audio or video interference press and
release RESET button to switch transmitter to a different channel .
04
5.REGISTER/PAIR CAMERA FOR WITH 2.4" SCREEN BABY MONITOR:
● Turn camera power ON
● Turn Monitor ON
Menu/OK → Main Menu → Multi Camera → Register
Camera → Camera 1 → Register Camera 1? → Yes
On transmitter/camera → On/Off
Note:Press and quickly release the ON/OFF/PAIR button on the CAMERA
to complete pairing process.
● Press"OK/MENU"button on the monitor to display Main Menu.
● Use "UP"or "DOWN"button to highlight "Multi Camera" Option and
press "OK/MENU" button to complete the selection.
● From "Multi Camera" Menu highlight "Register Camera" using "UP" or
"DOWN" button and press "OK/MENU"button to complete the selection
● From "Register Camera" Menu highlight one of the available(not used)
camera number you want to assign to this new camera and press
"OK/MENU" button to complete the selection.
NOTE:Camera numbers which have already been allocated (used to register
existing cameras) have "thumbs up" sign next to the camera number.
● Use "UP" or "DOWN" button to select "Yes" and press "OK/MENU"
button to complete the selection;the screen will display "register camera
#" where # is the camera number you selected.
● Press and quickly release ON/OFF button on the CAMERA to complete
pairing process
● If pairing is successful, the screen will display "Camera # Registered",
where # is the camera number you selected in previous step. "Thumbs
up" sign will appear next to the camera #.
NOTE:If the pairing/registration process is not successful, repeat this
process again.
● Press "ESC" button twice to exit from the Menus and view the camera.
05
6.REGISTER/PAIR CAMERA WITH 3.2" SCREEN BABY MONITOR:
● Turn camera power ON
● Turn Monitor ON
Menu/OK → Main Menu→ Register Camera → Camera 1
→ Register Camera 1? → Yes
On transmitter/camera → On/Off
Note:Press and quickly release the ON/OFF/PAIR button on the CAMERA
to complete pairing process.
● Press"OK/MENU"button on the monitor to display Main Menu.
● Use "UP"or "DOWN"button to highlight "Register Camera" and press
"OK/MENU"button to complete the selection
● From "Register Camera" Menu highlight one of the available(not used)
camera number you want to assign to this new camera and press
"OK/MENU" button to complete the selection.
NOTE:Camera numbers which have already been allocated (used to register
existing cameras) have "thumbs up" sign next to the camera number.
● Use "UP" or "DOWN" button to select "Yes" and press "OK/MENU"
button to complete the selection;the screen will display "register camera
#" where # is the camera number you selected.
● Press and quickly release ON/OFF button on the CAMERA to complete
pairing process
● If pairing is successful, the screen will display "Camera # Registered",
where # is the camera number you selected in previous step. "Thumbs
up" sign will appear next to the camera #.
NOTE:If the pairing/registration process is not successful, repeat this
process again.
● Press "ESC" button twice to exit from the Menus and view the camera.
06

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Creation Date--Text             : 
Producer                        : Corel PDF Engine Version 1.0.0.458
Mod Date--Text                  : 
Creator Tool                    : CorelDRAW 版本 12.0
Modify Date                     : 2011:08:16 15:58:37+08:00
Metadata Date                   : 2011:08:16 15:58:37+08:00
Format                          : application/pdf
Title                           : user manual-Camera only0423
Document ID                     : uuid:6d3c83a4-8538-4623-beab-aeabc4050df2
Instance ID                     : uuid:0238fe51-7a7f-4e4b-9d27-1dcb277f70bb
Has XFA                         : No
Page Count                      : 6
Create Date                     : D:20110802103926
Creator                         : CorelDRAW 版本 12.0

EXIF Metadata provided by EXIF.tools