E Zone Guardian EZ12031 SPREAD SPECTRUM TRANSMITTER User Manual
E-Zone Guardian SPREAD SPECTRUM TRANSMITTER
User Manual
E-ZONE GUARDIAN
FCC CERTIFICATION COMPLIANCE USING DIGI INT'L. ANTENNA
THE E-ZONE RF MODULE IS INTENDED TO PROVIDE WIRELESS DATA TRANS-
AVAILABLE CPU I/O LINES, STORES THE DATA AND PERIODICALLY TRANSMITS
WILL LINK ONLY WITH OTHER UNITS CONTAINING THE SAME INTERNAL ID
BETWEEN TWO MODULES WHICH CANNOT COMMUNICATE DIRECTLY WITH
PCB MOUNT: HIROSE PART NUMBER H.FL-R-SMT(10)
PART NUMBER A24-HASM-450. SUBSTITUTION OF OTHER ANTENNA
MISSION BETWEEN TWO LINKED UNITS. THE RF UNIT ACCEPTS DATA OVER
IT TO THE OTHER UNIT. DATA MAY MOVE IN ONE OR BOTH DIRECTIONS. UNITS
CODES. UNITS MAY ALSO FUNCTION AS INTERMEDIATE RELAY BY LINKING OF SECTION 15.231(e) OF THE FCC RULES. THE TIMING REQUIREMENTS
USER WARNINGS AND FCC REQUIREMENTS FOR THEIR EQUIPMENT IN
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OEM ENGINEERS USING THIS E-ZONE RF MODULE ARE CAUTIONED
USER DEFINED OUTPUT
USER DEFINED OUTPUT
THESE LINKING FUNCTIONS AS WELL AS THE RADIO CONTROL AND FEATURE
TWO READILY AVAILABLE TEXAS INSTRUMENTS PROVEN COMPONENTS.
THE CC2591 RF FRONT END INCLUDES PA,LNA,SWITCHES,BALUN, RF
OUTPUT POWER AND IMPROVE RECEIVER SENSITIVITY ON A 2.4GHz LOW-
POWER RF SIGNAL PRODUCED BY THE CC2531, WHICH IS AN IEEE 802.15.4
ARE PRESET AND FIXED AND NON-ADJUSTABLE BY THE END USER.
FCC RULES WHEN TRANSMITTING. END USERS MUST INCORPORATE ALL
SHOULD BE AWARE OF THE RF EXPOSURE LIMITS SPECIFIED IN
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
SUPPLIED LABEL P/N 101-001003 OR "CONTAINS FCC ID O4UEZ12031"
OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
FUNCTIONS ARE PREPROGRAMMED INTO THE MODULE WHICH UTILIZE
MATCHING NETWORK AND INDUCTOR, AND IS IMPLEMENTED TO INCREASE
COMPLIANT RF SYSTEM-ON-CHIP PROGRAMMED TO PROVIDE BOTH
THIS DEVICE COMPLIES WITH THE OPERATIONAL AND TIMING REQUIREMENTS
WARNING: END USERS ARE RESPONSIBLE TO ASSURE COMPLIANCE WITH
OPERATIONAL MANUALS. INSTALLERS AND USERS OF THIS EQUIPMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
THAT THEY MUST INCLUDE IN THEIR OWN PRODUCT MANUAL THE
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
E-ZONE GUARDIAN, PO BOX 774, CEDAR HILL,TX 75106-0774 8-1-12 REV. 1.0
1. ANTENNA PORT CONNECTOR
MAY INVALIDATE FCC CERTIFICATION.
FREQUENCY HOPPING AND SPREAD SPECTRUM.
FOLLOWING WARNING STATEMENT OF FCC PART 15.19:
USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
EACH OTHER.
SECTION 15.247(b)(4) OF THE FCC RULES.
MUST BE ON THE OEM USER'S FINAL PRODUCT.
RADIO MODULE
EZR 101-1000
1. ANTENNA USER DEFINED INPUT
USER DEFINED INPUT
P1.3 TO GROUND
P1.2 TO GROUND
OUT1
OUT2
2. JTAG
PGM
PORT
OUT 1
OUT 2
IN 1
TO +3.3V
TO +3.3V
IN 2
GROUND
USBN
+3.3VDC
CPU P2.1
RESET_N
GROUND
+3.3VDC
+3.3VDC
CPU P2.2
USBP
2. JTAG
PGM
PORT
3. USB
IN 2
IN 1
3. USB
PORT
D2
D1
FRONT
INSIDE
BACK