EDUP Electronics Technology EPN8508GS EP-N8508GS User Manual EP N8508GS use munual

Download:
Mirror Download [FCC.gov]
Document ID	2959936
Application ID	Js02JOtzdsay6uaZhPpAOA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.08kB (913525 bits)
Date Submitted	2016-04-15 00:00:00
Date Available	2016-04-18 00:00:00
Creation Date	2016-04-13 16:13:19
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2016-04-13 16:13:19
Document Title	Microsoft Word - EP-N8508GS?use?munual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Jiankuai

USB Wireless Adapter(RTL8188CUS) Quick
Installation Guide
Note：This Manual based on WindowsXP & Windows7
1.WindowsXP
01. Once the wireless USB adapter be plugged into an USB port, the following message will
appear on screen. Click “Cancel”, As the following picture shows.(If it does not pop‐up,Skip
this step)
02. Please insert the disc into your CD‐ROM drive. The disc should auto start, dispaying the
follwing window, If it does not start due to the system setting, open the browser window, find the
Setup.exe file in your CD‐ROM folder, click to run it.If you do not have CD,you can download at
EDUP official website:www.szedup.com
03. Double click Setup.exe file, Software begin to initialization,then click the “next”.There shows
the installation progress.
04. Do not interrupt installation , Click “finish” to finish the driver installation.The computer
automatically restart.
Wireless Connection （two ways to realize）
Wireless Connetion 1
05. 05. Click Icon
in the Windows system tray, which locates in the bottom‐right corner of
your computer screen or double click
, and pops up a message and click”Available
Network” Double‐click the utility icon or right click the icon and then select “View Available
Wireless Networks” to launch the utility. the Wireless Network Connection window appears and
displays your wireless network listed with the SSID you chose.
If the network security key hasn’t been inputted before, enter the network’s security key to
access the wanted SSID. Type the encryption key that you wrote down earlier in both the
Network key and Confirm network key boxes, and then click “ok”.
Wireless Connection 2
06. Click Icon
in the Windows system tray, which locates in the bottom‐right corner of your
computer screen or double click
, pops up a message and click”Windows Zero
Config”(Figure1),pay attention to the change of figure2.nad click “ok”button on the pop up page.
and then select the your preferred network, and then Double click,
07. Double Click Icon
enter the network’s security key to access the wanted SSID. Type the encryption key and then
click “Connect”.Or choose your wifireless signal and click connect as figure1,and enter the
password
and
then
click”connect.
Internet
now
is
available.
2. Windows7
01. Once the wireless USB adapter be plugged into an USB port (If do not have CD‐ROM.please
download on www.szedup.com), put in the CD and find windows file “winxpwinvistawin7win8”
andSetup.exe.
02. Double click Setup.exe file, Software begin to initialization,then click the “next”.There shows
the installation progress.
03. Do not interrupt installation, Click “finish” to finish the driver installation.The computer
automatically restart.
Wireless connection (two ways to realize
Wireless connection 1：
04. Click Icon
in the Windows system tray, which locates in the bottom‐right corner of
your computer screen or double click
, and pops up a message and click”Available
Network” Double‐click the utility icon or right click the icon ,and the Wireless Network
Connection window appears then double click the SSID you preferred.
Type the encryption key that you wrote down earlier in both the Network key and Confirm
network key boxes, and then click “ok”.
Note:if there is no icon
pictures shows:
,please find it in the on right buttom,it have been hide as following
Wireless Connection2.
05. Click Icon
which locates in the bottom‐right corner of your computer screen,click the
wireless network list and choose the SSID you preferred. and double click(Or click “Connect”).
Type the encryption key and then click “ok”.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between thee quipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 0.144 W/kg averaged over one gram of tissue. Device types:
EP-N8508GS (FCC ID: 2AHRDEP-N8508GS) has also been tested against this SAR limit. The highest
SAR value reported under this standard during product certification for use at the ear is 0.76W/kg and
when properly worn on the body is 0.60W/kg. This device was tested for typical body-worn operations
with the back of the handset kept 1cm from the body. To maintain compliance with FCC RF exposure
requirements, use accessories that maintain a 1cm separation distance between the user's body and the
back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic
components in its assembly. The use of accessories that do not satisfy these requirements may not
comply with FCC RF exposure requirements, and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a
minimum separation distance of 1cm must be maintained between the user’s body, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device should not contain any
metallic components. Body-worn accessories that do not meet these requirements may not comply with
RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Jiankuai
Create Date                     : 2016:04:13 16:13:19+08:00
Modify Date                     : 2016:04:13 16:13:19+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Jiankuai
Title                           : Microsoft Word - EP-N8508GS?use?munual
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:af9c822d-a68f-452d-b4be-9534e54764a0
Instance ID                     : uuid:7f883ea3-1b40-454b-be7a-8ecf0bba2f8d
Page Count                      : 16

EXIF Metadata provided by EXIF.tools