ELITEGROUP COMPUTER SYSTEMS G553IBXX Notebook PC with 802.11b WLAN User Manual G553 user namual update

Download:
Mirror Download [FCC.gov]
Document ID	466178
Application ID	IwaKh8kv33U4VvwEJumIng==
Document Description	Users Manual Part 2 Revision 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	131.31kB (1641371 bits)
Date Submitted	2004-09-07 00:00:00
Date Available	2004-08-29 00:00:00
Creation Date	2004-09-03 06:37:48
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-09-03 14:42:06
Document Title	Microsoft Word - G553 user namual update.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	jennifer

The computer is equipped with several interface ports, including an enhanced parallel
(printer) port, a serial port, and USB ports. These are provided as a means of
connecting peripheral devices to the computer.
Connect peripheral devices to the computer's interface ports as shown below:
56
57
Page intentionally left blank
58
Running BIOS Setup
Introduction
The BIOS (Basic Input and Output System) Setup program is a menu driven utility
that enables you to make changes to the system configuration and tailor your system
to reflect installed hardware or alter system performance. When the Notebook is
turned back on, the system is configured with the values stored in CMOS. With easyto-use menus, you can configure such items as:
• Hard drives and peripherals
•
•
Bootup Drive Sequence
Password protection
The settings made in the BIOS Setup program intimately affect how the Notebook
performs.
Navigating through BIOS Setup
The Setup program has been designed to make it as easy to use as possible. If you
accidentally make a setting and don’t know which one to switch back to, the Setup
program has a hot key that allows you to return to the previous value.
Accessing the BIOS Setup Program
To access the BIOS Setup program, press the DEL key after the Notebook has run
through its POST.
Item Specific Help
On the right side of the Setup screen is an area labeled Item Specific Help. This area
will list navigation key shortcuts and information that is specific for the item that you
are currently editing.
The Menu Bar
The top of the screen has a menu bar with the following selections:
Main - Use this menu to make changes to the basic system configuration.
Advanced - Use this menu to enable and make changes to the advanced features
available on your system, such as enabling the FIR module.
60
Security - Use this menu to set a password.
controls access to the BIOS setup menu.
The password allows bootup and
Boot - Use this menu to configure the default system device used to locate and load
the Operating System and for booting up the Notebook.
Exit - Use this menu to exit the current menu or specify how to exit the Setup
program.
To access the menu bar items, press the right or left arrow key on the keyboard until
the desired item is highlighted.
The Legend Bar
At the bottom of the Setup screen you will notice a legend bar. The keys in the
legend bar allow you to navigate through the various setup menus.
The following table lists the keys found in the legend bar with their corresponding
alternates and functions.
Legend Key
Alternate
Key
Function
F1
Displays the General Help window. It can be
enabled from anywhere in the BIOS.
Esc
Jumps to the Exit menu or returns to the Main
menu from a submenu.
←
Selects the menu item to the left.
→
Selects the menu item to the right.
↑ or ↓
Keypad
arrow keys
Moves the cursor up and down between fields.
Tab
Enter
Moves the cursor to the next position available in
the field.
61
Minus key (-)
Scrolls backward through the values for the
highlighted field.
Plus key (+)
Scrolls forward through the values for the
highlighted field.
Home
PgUp
Moves the cursor to the field at the top of the
window.
End
PgDn
Moves the cursor to the field at the bottom of the
window.
F9
Sets the parameters for the current menu to their
default values.
F10
Save and Exit.
Enter
Will select a sub menu or show a range of options
for a field.
Launching Submenus
Note that a right pointer symbol υ appears to the left of certain fields. This pointer
indicates that a submenu can be launched from this field. A submenu contains
additional options for a field parameter.
To call up a submenu, simply move the cursor to highlight the field and press the
[Enter] key. Use the [Esc] key to return to the Main menu.
General Help
In addition to the Item Specific Help window, the BIOS Setup program also provides
a General Help screen can be called up from any menu by simply pressing [F1].
62
Use the [PgUp] and [PgDn] keys or the up and down arrow keys (↑↓) to scroll
through the entire help document. Press the Home key to display the first page, press
End to go to the last page. To exit the help window, press the [Enter] or the [Esc]
key.
Save Changes and Exit the Setup Program
Refer to the Exit menu section of this chapter for detailed information on saving
changes and exiting the setup program.
The Main Menu
When the Setup program is accessed, the following screen appears:
63
The Advanced Menu
Selecting Advanced from the menu bar displays the Advanced menu:
64
The Security Menu
The Notebook’s advanced system of security allows you to set a password to prevent
unauthorized access to system resources, data, and the BIOS Setup Program.
65
The Boot Menu
The Boot menu allows the user to specify the order in which the Notebook is to check
for a device to boot the system. You can also configure the way that the system will
boot up.
To make changes, select Boot from the menu bar. The following screen appears:
66
The Exit Menu
Once you have made all of your selections from the various menus in the Setup
program, you should save your changes and exit Setup. Select Exit from the menu
bar to display the following menu:
67
Page intentionally left blank
68
The Software Utilities Disks
AutoRun Installation
Follow the step-by-step procedures on the CD-ROM/DVD-ROM to execute the
“AutoRun” application by selecting the topic of “Driver Installation”.
If you encounter this message when executing the Auto Run in
Windows 2000, please perform the following procedures:
Click on the “Start” – “Setting” – “Control Panel” – “System” –
“Advanced” tab – “Performance” tab – “Change” tab – reduce the
maximum Virtual Memory setting to 200MB.
Installing the INTEL_INFINST Driver
•
•
•
•
•
•
Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
Click “Start” and Select “Run”.
Type the following: D:\Driver\INTEL_INFINST\INFINST_enu (If D is not your
CD-ROM/DVD-ROM drive, substitute D with the correct drive letter).
Click on “INFINST_enu” to begin the Installation Wizard.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Installing VGA Display Drivers
This section describes the operation and installation of VGA display software drivers
supplied on the Driver Utility CD-ROM that is shipped with your computer.
• Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
• Click “Start” and Select “Run”.
• Type the following: D:\Driver\VGA\Win2K&XP\Setup.exe (If D is not your CDROM/DVD-ROM drive, substitute D with the correct drive letter).
• Click on “Setup” to begin the Installation Wizard.
• Follow the Wizard’s on-screen instructions to complete the installation.
• Restart the system.
Intalling the Audio Driver
To install the audio driver you must first remove the currently installed driver.
70
•
•
•
•
•
•
Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
Click “Start” and Select “Run”.
Type the following: D:\Driver\Audio\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter).
Click on “Setup” to begin the Installation Wizard.
Follow the Wizard’s on-screen instructions to complete the installation.
Restart the system.
Intalling the IR Driver
To install the audio driver you must first remove the currently installed driver.
• Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
• Click “Start” and Select “Run”.
• Type the following: D:\Driver\IR\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter).
• Click on “Setup” to begin the Installation Wizard.
• Follow the Wizard’s on-screen instructions to complete the installation.
• Restart the system.
Intalling the LAN Driver
To install the LAN driver you must first remove the currently installed driver.
• Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
• Click “Start” and Select “Run”.
• Type the following: D:\Driver\LAN\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter).
• Click on “Setup” to begin the Installation Wizard.
• Follow the Wizard’s on-screen instructions to complete the installation.
• Restart the system.
71
Installing the TouchPad Driver
To install the touchpad driver you must first remove the currently installed driver.
• Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
• Click “Start” and Select “Run”.
• Type the following:
D:\Driver\Touchpad\Win2K&XP\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter).
• Click on “Setup” to begin the Installation Wizard.
• Follow the Wizard’s on-screen instructions to complete the installation.
• Restart the system.
Installing the MDC Modem Driver
Please follow these instructions to install the Modem driver:
• Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
• Click “Start” and Select “Run”.
• Type the following:
D:\Driver\MDC\Liteon\Win2K&XP\MDMCHIPV.inf or
D:\Driver\MDC\Billionton\WinXP\Setup.exe or
D:\Driver\MDC\Billionton\Win2K\Setup.exe or
D:\Driver\MDC\QCOM\Win2K&XP\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter).
• Click on “Setup” to begin the Installation Wizard.
• Follow the Wizard’s on-screen instructions to complete the installation.
• Restart the system.
Installing the MiniPCI Wireless LAN Card Driver
Please follow these instructions to install the Wireless LAN driver:
72
•
•
•
•
•
•
From Start, click on the "My Computer" icon and click the "View System
Information".
Click on the "Hardware" tab from the "System Properties" dialog window.
Click the "Device Manager" button.
Double click on the "Other Devices" , double click the " Network Controller "
and click on the "Driver" tab.
Click the "Update Driver" tab and select the "Install from a list or specific
location (Advanced)" item and click "Next".
Select the "Include this location in the search" item and click on the "Browse"
button and specify for the designate location of your CD driver
D:\Driver\MiniPCI\Intel\21003B\PROW7100\WinXP\W70N51.inf (WinXP Intel
21003B)
D:\Driver\MiniPCI\Intel\21003B\PROW7100\Win2K\W70N5.inf (Win2K Intel
21003B)
D:\Driver\MiniPCI\Intel\2200BG\PROW2200\WinXP\W22N51.inf (WinXP Intel
2200BG)
D:\Driver\MiniPCI\Intel\2200BG\PROW2200\Win2K\W22N50.inf (Win2K Intel
2200BG)
D:\Driver\MiniPCI\Billionton\WinXP\NET8180.inf (WinXP Billionton)
D:\Driver\MiniPCI\Billionton\Win2000\NET8180.inf (Win2K Billionton)
D:\Driver\MiniPCI\QCOM\802MR\WinXP\NET8180.inf (WinXP QCOM 802MR)
D:\Driver\MiniPCI\QCOM\802MR\Win2000\NET8180.inf (Win2K QCOM
802MR)
VGA Utilities
After you have restarted Windows, open the “Control Panel” and double click on the
“Display” icon. From the “Display Properties” window, select the “Settings” tab and
click on the “Advanced” tab to enter the “INTEL® 82852/82855 GM/GME Graphics
Controller Properties" window.
73
Devices
You can connect up to three displays simultaneously to the notebook. You can watch
a DVD movie on an external television while checking email on your notebook
screen - or surf the web on a CRT monitor while working on a presentation on a
digital flat panel. The option is yours with these features.
74
75
76
77
78
Color
You can adjust the right resolution for your screen display.
79
Schemes
80
Hot Keys
81
OpenGL
82
Page intentionally left blank
83
Troubleshooting
This chapter describes locating and solving problems that you may encounter while
using your computer.
Locating a Problem
Problems with your computer can be caused by something as minor as an unplugged
power cord – or as major as a damaged hard disk. The information in this chapter is
designed to help you find and solve minor problems. If you try all the suggested
solutions and you still have a problem, make a list of what steps you have taken to
correct the problem and contact your dealer.
Successful troubleshooting is the result of careful observation, deductive reasoning,
and an organized approach to solving the problem.
The problems that you will encounter can be divided into two basic categories:
hardware problems and software problems. Hardware problems can be further divided
into electrical and mechanical problems. You will know you have a hardware
problem if the screen is dark, the computer cannot read the disk drives, or you get an
error message during the Power-On Self Test (POST).
Software errors can occur at several levels. The ROM BIOS and the operating system
can give you a large number of error messages. On top of this, each application
software package has its own set of error messages. It is important to determine
whether the software error message you are getting is from the application or the
operating system. Once you know this, you can look in the respective manual for a
solution to the problem.
Checking Cables and Connections
Start by performing a careful visual inspection of the exterior of the computer. If no
LEDs are illuminated, make sure that your computer and its peripherals are getting
power and communicating with each other properly.
To check the power cables, and connections:
1.
If you have been using battery power, connect the Notebook to an external
power source and make sure that the battery has a charge.
2.
If you are using the Notebook with the AC adapter, check the power outlet, the
power cord, and any power switches that may affect your computer.
85
Check the wall outlet or power strip with an item that you know is
functioning properly. A lamp or radio is a convenient item for checking the
power. You may also need to check the fuses and breakers in your electric
box.
If the outlet is controlled by a wall switch, make sure that the switch is on.
If the outlet is controlled by a dimmer switch, use a different outlet.
If your computer is plugged into a power strip with an On/Off switch, make
sure the switch is on.
3.
With the computer’s power switched off, check all cable connections. If the
computer is connected to any peripheral devices, look for loose or disconnected
cables.
If the computer is too close to a wall, a cable connection may be loose or the cables
may be crimped.
Do not substitute cables for different devices (other than the
manufacturer recommended cables) even if they look exactly alike. The
wiring inside the cable may be different.
4.
When you are certain that you have power available and all connections are
good, turn the computer on again. If the computer still does not start, you may
have a hardware problem.
The Power-On Self Test
The Power-On Self Test (POST) runs every time you turn on or reset the Notebook.
The POST checks memory, the main system board, the display, the keyboard, the disk
drives, and other installed options.
A few seconds after you turn on your computer, a copyright message appears on your
display screen. A memory test message appears next; as the test continues, memory
size increases until all installed memory is tested. Normally, the only test routine
visible on the screen will be the memory test.
86
Two classifications of malfunctions can be detected during the POST:
• Error messages that indicate a failure with either the hardware, the software, or
the Basic Input/Output System (BIOS). These critical malfunctions prevent the
computer from operating at all or could cause incorrect and apparent results. An
example of a critical error is microprocessor malfunction.
• Messages that furnish important information on the power-on and boot processes
(such as memory status). These non-critical malfunctions are those that cause
incorrect results that may not be readily apparent. An example of a non-critical
error would be a memory chip failure.
In general, if the POST detects a system board failure (a critical error), the computer
halts and generates a series of beeps. If failure is detected in an area other than the
system board (such as the display, keyboard, or an adapter card) an error message is
displayed on the screen and testing is stopped. It is important to remember that the
POST does not test all areas of the computer, only those that allow it to be
operational enough to run diagnostic programs.
If your system does not successfully complete the POST, but displays a blank screen,
emits a series of beeps, or displays an error code, consult your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented in the table
below:
Problem:
Failure in the installation of the Audio driver.
Be sure to first remove the current audio device from your system.
Please follow the instruction on the installation of audio driver.
Solution:
Problem:
The display screen is dark
87
Solution: Make sure that the computer is not in Suspend mode. Check the
Brightness controls for the screen. If the controls are turned too far down, the
screen will be dark.
Problem:
An incorrect date and time are displayed.
Solution: Correct the date and time using the DOS DATE and TIME commands
or the options in the Setup Utility. If the date and time become incorrect after a
short time, your CMOS battery may be depleted. Contact your dealer to change
the battery.
The message: “Invalid system disk, Replace the disk, and then press
any key” appears during boot.
Problem:
Check and make sure that you do not have a non-bootable floppy
diskette inserted in your floppy drive. If your USB FDD is empty, you may not
have an operating system installed on your drive. Contact technical support for
assistance.
Solution:
Problem: You hear irregular beeps during operation of the Notebook and the
system halts.
Solution:
The problem is beyond the scope of this manual. Contact technical
support.
Problem:
An unidentified message is displayed.
Reboot the computer and run the BIOS system setup. Confirm the
Setup parameters. If the same message is displayed after booting up again,
contact technical support for assistance.
Solution:
Problem:
88
The system cannot access the CD-ROM/DVD-ROM drive.
Solution: Check that a CD is properly inserted in the drive. Make sure that you
are using the correct program for that kind of CD. For example, the system
cannot read a data CD using an audio program.
Problem:
You cannot operate the printer.
Solution: Check the printer cable connection. Ensure that the printer power
switch is turned on. Confirm that the printer is on-line.
Problem:
You can’t save data to disk.
Solution: Ensure that the disk has been formatted.
Consult your operating system manual for information on formatting floppy
diskettes.
Problem:
The diskette is write-protected.
Solution:
Eject the diskette, remove the write protection, and try again.
Problem:
The diskette if full.
Try using another diskette or free up some space on the diskette. The
disk drive is not operating. Contact your dealer for support.
Solution:
Problem:
•
•
•
You cannot use the mouse.
Check the cable connection.
Check the mouse with another application to see if there is a software
incompatibility problem.
If possible, check the mouse with another computer to see if it works. If it
doesn’t operate on a different system, the mouse might be broken.
Contacting Your Dealer
89
If you still have a problem after reading the preceding sections, the next step is to
contact your dealer. Your dealer can determine if the problem is something that
requires the computer to be taken to the shop. Before you call your dealer, however,
prepare the following information:
• How is your computer configured? Your dealer needs to know what peripheral
devices you are using.
• What messages, if any, are on the screen?
• What software were you running at the time?
• What have you done already to try to solve the problem? If you have overlooked
a step, your dealer may be able to solve the problem over the phone.
90
Page intentionally left blank
91
Upgrading your System
Upgrading your Memory
Refer to the following instructions and illustration for information on upgrading your
notebook's memory.
1.
Turn off the computer and disconnect the AC adapter and all peripherals.
2.
Turn the notebook over so that the rear ports are facing you and locate the
memory module compartment.
3.
Remove the screws that secure the RAM module compartment cover and set it
4.
5.
6.
7.
8.
9.
1 0.
aside in a safe place.
Remove the compartment cover and then angling it up and out.
If you need to install a higher capacity module, gently push the edge clips on
both sides to release the module. Angle the card slightly upward and gently
slide it from its edge connector slot. Store the card in the anti-static bag that
contains your new module(s).
To install the new memory card, hold the card with its gold edge connector
toward the edge connector slot of the compartment. To help you orient the
cards, the edge connector has been made with two unequal-length sections.
You will only be able to insert the card in one direction.
Insert the edge connector into the slot. The gold edge connector of the card
should not be visible when the card is fully inserted.
Press the card downward where you should hear an audible click as the latches
of the connector secure the card in place.
Once the module is properly seated, you can replace the cover on this
compartment.
Replace and tighten the screw.
93
The Easy to Upgrade HDD Module
The hard drive in your notebook computer is made to be easily swapped out for
upgrading. You should back up your hard drive before attempting o change the hard
drive. Make sure that before you install a new drive, all the files in your system
should be backed up.
To upgrade your Hard Drive
94
1.
2.
3.
4.
5.
6.
7.
8.
9.
Power down the system completely. Turn the system over with the front of the
unit facing you.
Remove the three screws that secure the compartment cover and set them in a
safe place.
Slide the HDD cover away from the compartment.
The drive is attached to a special bracket that secures it to the notebook
computer. There are 4 screws hold the bracket. Remove the screws and set
them in a safe place.
Push the HDD slightly in the direction of the arrow as shown in the illustration
to release it from the pins of the drive.
Gently hold the grip of the HDD, lift it up to release from its compartment.
To install the new HDD, you will need to align the tabs on the drive bracket
with the slots on the bay. Press down gently on the drive bracket until it
engages with the system. Do not force the drive into place this can bend the
pins on the hard drive.
Slide the compartment cover into place and be sure the screw holes on the cover
align completely with the screw holes in the case.
Secure the cover with the three screws.
Upgrading your System CPU
Refer to the following instructions and illustration for information on upgrading your
notebook's CPU
1.
Turn off the computer and disconnect the AC adapter and all peripherals. From
the rear side of your notebook, use your index finger to lift up the hinge cover
attached to the LCD screen.
2.
Bend your LCD screen into 90 degree angle then carefully lift up the hinge
cover.
95
96
3.
Remove the screen that is attached to the keyboard in order to remove the
heatsink on top of the CPU.
4.
Remove all the screws attached to the heatsink.
5.
Before removing the screws, there are certain measures to followed in removing
the heatsink
6.
7.
To remove the heatsink, first loosen the screw carefully.
After loosening one screw, be certain that the next to be loosen should be the
screw on its adjacent side as shown on the illustration.
Be sure to loosen all the screws first before removing it totally to
release the heatsink. Failure to do so will cause a major damage to
the heatsink.
8.
Now you can totally remove all the screws also in that order when you first
loosen the screw.
97
Specification
Detailed Notebook Specifications
General
CPU
•
•
Intel Pentium-M Banias processor from 1.3GHz to 1.7GHz, 1M L2 cache
Intel Dothan processor from 1.8GHz to 2.0GHz, 2M L2 cache
•
•
478 pin uFC-PGA2 478 socket, CPU front-side bus up to 400MHz
TDP : 21W.
Core Logic
•
•
Intel 855GM/GME,
Support FSB 400MHz
Memory
Main Memory
•
•
•
•
•
2 expandable memory slot up to 2GB,1GB per DIMM Max. with 512Mb
technology
128/256/512 MB memory options
Two 200 pin SO DIMM type memory slots
2.5V TSOP/CSP/WBGA DDR SDRAM
Supports DDR266/333 Synchronous SDRAM
ROM
•
•
512KB Flash ROM factory option, 3V erase
Boot block protection
Mass Storage
HDD
•
•
Support enhanced IDE (PIO mode 4) and bus master(Ultra DMA 33/66/100
mode).
Removable hard disk drive, 2.5” 9.5mm.
99
Module Bay
•
•
Supports CD-ROM/DVD-ROM/Combo Drive (DVD-ROM+CD-RW), DVD-RW,
DVD+RW, DVD-Dual; 5.25” 12.7mm height
Fast IDE and ATAPI interface CD-ROM/DVD-ROM/Combo Drive (DVDROM+CD-RW), DVD-RW, DVD+RW, DVD-Dual
Pointing Devices
•
•
Synaptics TouchPad
Support four way scrolling feature
Keyboard
•
•
•
•
•
US/Europe, DOS/V keyboard for Japan, full size keyboard alike pitch
300 mm keyboard with key stroke 3.0mm
Twelve function keys and Windows Function key
Internal keyboard works a standard 101/102 desktop keyboard
2 short-cut keys: WWW & eMail
Audio
Controller
•
Built-in Intel ICH 4-M chipset
Codec
•
100
Realtek ALC202A
Features
•
•
•
•
•
Dual full-duplex Direct Sound Channels
Hardware SoundBlaster Pro for real-mode DOS legacy compatibility
18-bit ADC & DAC resolution
Support S/PDIF out
AC’97 2.2 & PC2001 compliant
I/O Ports
Standard Ports
•
•
•
•
•
•
•
•
•
•
One parallel port supported EPP/ECP (25-pin female D-connector)
One S-video TV out port for TV
One DC input port for External AC adapter (2-pin DC jack)
One Type II PCMCIA card socket
One video port for external analog VGA monitor (15-pin female D-connector)
USB 2.0 port x 2
MIC-in, headphone jack w/ adaptor for 5.1 channel SP/DIP support
RJ-11 jack for Fax/Modem
RJ-45 jack for LAN
IEEE 1394 mini-jack
PCMCIA
•
•
•
Controller : RICHO R5C551
Supports 1 PC Card/CardBus slot
Supports 16-bit & cardBUs PC Cards, PCI rev. 2.2 and PC Card Standard Release
7.0 compliant
101
•
•
Integrated IEEE 1394a OHCI-link & two ports with IEEE 1394 internal PHY
Data transfer rate : 100/200/400 Mbps
Graphics and Video
Controller
•
Intel 855GM/GME internal graphics.
Features
•
High performance 3D graphics engine (floating triangle setup/rendering)
Graphic Memory
•
Up to 64 MB of dynamic video memory allocation
LCD Display
•
14.1”XGA/15”XGA/15” SXGA TFT
Electrical
AC Adapter
•
External universal type AC adapter, output maximum 65W
Smart Battery
•
•
•
•
102
Li-Ion battery @ 27 Whrs (4-cell); Optional 8-cell 53W
User interchangeable
Removable and rechargeable
3 hrs charge time while system off
•
•
•
4 hrs charge time while system on
Charging time for one battery pack : 3.5 hours to full charge when system off or
in suspend
More than 2.0 hrs w/ 4-cell battery, 4.0 hrs w/ 8-cell battery
Dimensions
•
326(W) x 258(D) x 25.3(H) mm/32mm (front/back)
Weight
•
2.4kg with 14.1” panel, Battery and DVD-ROM Drive installed
Operating Environment
Temperature
•
•
Operating: 5°C ~ 35°C
Storage: -20°C ~ 60°C
Humidity
•
•
Operating: 30% ~ 90% (non-condensing)
Non-operating: 10% ~ 90% (non-condensing)
Altitude
•
•
Operating: -200 to 10,000 feet above sea level
Non-operating: -200 to 30,000 feet above sea level.
Options
•
Spare Li-Ion Battery Pack : 4-cell battery and 8-cell battery
103
•
•
•
•
Factory Option : 802.11b wireless LAN with MiniPCI slot
Memory Extension Card
Module bay : CD-ROM/ DVD-ROM/ Combo(DVD-ROM+CD-RW) Drive, DVDRW, DVD+RW, DVD-Dual
Bootable external USB FDD
Accessories
•
•
•
User‘s Manual & Driver CD title
AC Adapter
Power Cord
Software Specifications
System Software
•
•
•
104
System BIOS: AMI BIOS
Supported Operating Systems
Optional Windows XP or above version
Standard Software Drivers
INTEL_INFINST driver,
VGA driver,
Audio driver,
Touch-Pad driver,
IR driver,
MDC Modem driver,
LAN driver,
MiniPCI Wireless LAN driver
Declaration of Conformity
1. Notebook / Green553
2. This device complies with part 15 of FCC rules. The operation is subject to the
following two conditions: (1) The device may not cause harmful interference. And (2)
this device must accept any interference received, including the interference that may
cause undesired operation
Information of Responsible Party in USA
Contact Person: Hank Yu
Company Name: Elitegroup Computer Systems, Inc. US Headquarter
Address: 45401 Research Ave, Fremont CA 94539
TEL: 510-226-7333
FAX: 510-226-7350
E-mail: Support@ecsusa.com
105

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:09:03 06:37:48Z
Modify Date                     : 2004:09:03 14:42:06+08:00
Page Count                      : 50
Creation Date                   : 2004:09:03 06:37:48Z
Mod Date                        : 2004:09:03 14:42:06+08:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : jennifer
Metadata Date                   : 2004:09:03 14:42:06+08:00
Creator                         : jennifer
Title                           : Microsoft Word - G553 user namual update.doc
Has XFA                         : No

EXIF Metadata provided by EXIF.tools