ELITEGROUP COMPUTER SYSTEMS MPC Personal Computer User Manual ECS SI mPC 2

ELITEGROUP COMPUTER SYSTEMS CO., LTD Personal Computer ECS SI mPC 2

Contents

User Manual-Part 1

User Manual ECS SI mPC
CopyrightDisclaimerThis publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.Version 1.0The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.Trademark RecognitionMicrosoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.Other product names used in this manual are the properties of their respective owners and are acknowledged.ECS SI mPC iiRegulatory Compliance InformationFCC Declaration of ConformityThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different form that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.This device meets the government’s requirements for exposure to radio waves.This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government, Industry Canada, and other national regulatory agencies.
Warning! Any changes or modifications made to the equipment which are notexpressly approved by the relevant standards authority could void yourauthority to operate the equipment.Waste disposal instructionDo not throw this electronic device into the trash can when discarding.To minimize pollution and ensure utmost protection of the global environment, please recycle it in European WEEE (waste electrical and electronicequipment) directive system or recycle system in Taiwan.iii ECS SI mPCMPE 䆖䃎džƉŽƐƵƌĞƚŽZĂĚŝŽ&ƌĞƋƵĞŶĐLJZĂĚŝĂƟŽŶ͗To comply with FCC RF exposure compliance requirements, a separation distance of at least 20cm must bemaintained between the antenna of this device and all persons. This device must not be co-located or operatingconjunction with any other antenna or transmitter.CE, FCC, NCC RF 䆖䃎This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator & your body.This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator & your body.Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 本產品符合低功率電波輻射性管理辦法 第十二條、第十四條等條文規定1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。䴫⻱⌒ᴍ䵢䟿MPE⁉Ⓠ٬1mW/cm ˈ䘱⑜⭒૱ሖ⑜٬⛪˖0.0941mW/cm22 Edition 1Part No.Printed in China OCT 2015Japan VCCI StatementCE mark. Declaring compliance to all the applicable European Union (EU) Directives. Any special accessories needed for compliance must be specified in the instruction manual. Use only shielded and terminated cables to connect I/O devices to this equipment.
ECS SI mPC iv^ŽƵƚŚ<ŽƌĞĂD͗ůĂƐƐEŽƟĐĞ이 기기는 가정용(B급)전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며,모든지역에서 사용할 수 있습니다.^ŽƵƚŚ<ŽƌĞĂZ&͗tĂƌŶŝŶŐƐƚĂƚĞŵĞŶƚ해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음Korea Certification mark. Includes an adjacent MSIP(Ministry of Science, ICT & future planning)certification number.
WTAdditional Information and Assistance1. Visit the ECS websites at www.ECS.com.tw where you can find the latest informationabout the product.2. C- Prod- D- D- A- The- This W1. 2. Pour éviter un choc électrique, ne pas retirer le couvercle. Aucune pièce réparable par l'utilisateur, voir l'entretien à du personnel qualifié. 1. Tension de sortie Tension d'entrée nominale 100-240 la note de 2. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des produits approuvés ou nettoyer avec un applicateur sec Warning!To prevent electric shock, Do not remove cover.No user serviceable parts inside, refer servicing to qualified personnel.Additional Information and Assistance1. 2. Contact your distributor, sales representative, or ECS’s customer service center fortechnical support if you need additional assistance. Please have the followinginformation ready before you call:- Product name and serial number- Description of your peripheral attachments- Description of your software (operating system, version, application software, etc.)- A complete description of the problem- The exact wording of any error messages - This equipment is a source of electromagnetic waves. Before use, please makesure that there are not EMI sensitive devices in its surrounding which maymalfunction thereforeWarning! 1. Input voltage rated 100-240V~, 50~60Hz, 0.9A maxOutput Voltage rated 3.0A, 12Vdc2.Maintenance: to properly maintain and clean the surfaces, use only approvedproducts or clean with a dry applicatorAttention!Pour éviter un choc électrique, ne pas retirer le couvercle. Aucune pièce réparable par l'utilisateur, voir l'entretien à du personnel qualifié. Attention! 1. Tension de sortie Tension d'entrée nominale 100-240V~, la note de 3.0A, 12Vdc2. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des produits approuvés ou nettoyer avec un applicateur sec Packing List Before setting up the system, check that the items listed below are included and in goodcondition. If any items are missing, please contact your dealer immediately.ECS SI mPC x1Adapter x1User Manual x1Antenna x2 (Optional) VESA Mount Bracket x1 (Optional)50-60Hz, 0.9A max,v ECS SI mPC
Safety Instructions1. Read these safety instructions carefully. 2. Keep this User Manual for later reference.3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.Do not use liquid or spray detergents for cleaning.4. For plug-in equipment, the power outlet socket must be located near the equipmentand must be easily accessible.5. Keep this equipment away from humidity.6. Put this equipment on a reliable surface during installation. Dropping it or letting it fallmay cause damage.7. The openings on the enclosure are for air convection. Protect the equipment fromoverheating. DO NOT COVER THE OPENINGS.8. Make sure the voltage of the power source is correct before connecting theequipment to the power outlet.9. Position the power cord so that people cannot step on it. Do not place anything overthe power cord.10. All cautions and warning on the equipment should be noted.11. If the equipment is not used for a longt time, discounnect it from the power source toavoid damage by transient overvoltage.12. Never pour any liquid into an opening. This may cause fire or electrical shock.13. Never open the equipment. For safety reasons, the equipment should be opened onlyby qualified service personnel.14. If one of the following situations arises, get the equipment checked by servicepersonnel:a. The power cord or plug is damaged.b. Liquid has penetrated into the equipment.c. The equipment has been exposed to moisture.d. The equipment does not work well, or you cannot get it to work according to theuser’s manual.e. The equipment has been dropped and damaged.f. The equipment has obvious signs of breakage.15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGETEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.16. If your computer is losing time significantly or the BIOS configuration resets itselfto be default, the battery may have no power.17. IMPROPER INSALLATION OF VESA MOUNTING CAN RESULT IN SERIOUSPERSONAL INJURY! VESA mount installation should be performed by a professional technician; please contact the service technician or your retailer if youneed this service.18. Maintenace: to properly maintain and clean the surfaces, use only the approved products or clean with a dry applicator.ECS SI mPC vi
ContentsChapter 1 System Information .............................11.1 Introduction ................................................................................................ 21.2 Specifications ............................................................................................. 21.3 Cleaning/Disinfecting ................................................................................. 3Chapter 2 Getting Started ....................................42.1 System TourFigure 2.1 Top View ..................................................................... 5Figure 2.2 Bottom View ................................................................ 52.2 Distribution Description ..……………………………………………………… 7Chapter 3 Hardware Installation .........................83.1 Motherboard Introduction ....................................................................... 93.2 Installing the Motherboard .……..….…………………...….…..………....... 12Chapter 4 Using BIOS ........................................204.1 About the Setup Utility ............................................................................. 214.2 Using BIOS …………………………………………………………………… 22Figure 2.3 Side View .................................................................... 5Figure 2.4 I/O Side View............................................................... 62.3 Powering the System ..………………………………………………………… 7............................................................................................... 5vii ECS SI mPCChapter 5 Feature Inforamtion .........................395.1 Introduction ............................................................................................. 40
Chapter 11 System Information
1.1 IntroductionThe product has onboard Intel® Bay Trail-M SoC for personal micro desktop markets or educational usage. Below is a brief summary of the computer’s many feature:1.2 SpecificationsECS SI mPC 2Item Description CPU/SoC Intel® Bay Trail-M SoC Celeron N2830TDP 7.5WMemory Expansion SlotStorage 1 x SATA 3GB/s Connector Audio Chip Realtek ALC283-CG LAN Chip Front Port I/O 2 x USB 3.0 ports (Type-A)1 x IRRear I/O 1 x HDMI port (A type)1 x RJ45 LAN connector2 x USB 2.0 ports1 x 12V DC jack1 x Audio jack (Mic In/Line out)Internal I/O connectors & headers1 x DDR3L SO-DIMM socket, Max 8GB1 x Half-size mini-PCIe slot (supports mSATA, USB & PCIe signal) 10/100/1000 Mbps support (Ethernet port), RealtekRTL8111G 1 x 4-pin CPU FAN 1 x Serial ATA 3Gb/s connector1 x 5-pin SATA PWR connector 1 x 2-pin Battery connector 1 x 3-pin CLR CMOS 1 x Power ON LED 1 x Logo LED header 1 x 2-pin Wireless charger header (Not Support)1 x 4-pin Speaker 1 x 8-pin NFC headerForm Factor mPC-A 116.6*112*45.6 mm 0.595LmPC-AH 116.6*112*55.6 mm 0.726LOptional Device Storage type: 2.5” HDD, Half-size mini-PCIe mSATA SSD, SATADOMWLAN: 802.11b/g/n + Bluetooth4.0NFC: URAT interfaceWireless Charger: Compatible with Qi (Not Support)Speaker: Internal speaker 1Wx2NOTE:The features listed in this section is for your reference only. The exact configuration of the system depends on the model purchased.System BIOS 64Mb SPI ROM
Item DescriptionAdapter ASIAN POWER DEVICES INC. 12V, 3A, 36WWA-36A12FU-AAAMWA-36A12FG-AAAAWA-36A12FK-AAAAWA-36A12FS-AAAAWA-36A12FN-AAAAKUANTECH INCORPORATED COMPANY 12V, 3A, 36WKSAS0361200300D5KSAS0361200300HUKSAS0361200300HEKSAS0361200300HKKSAS0361200300HA1.3 Cleaning/DisinfectingDuring normal use ECS SI mPC may become solied and should, therefore, be cleaned regularly.Steps: 1. Wipe ECS SI mPC with a clean cloth that has been moistened in the cleaning solution.2. Prepare agent per manufacturer’s instructions or hospital protocol.3. Wipe thoroughly with a clean cloth.Caution! Do not immerse or rinse ECS SI mPC or its peripherals. If you accidentally spillliquid on the device, disconnect the unit from the power source. Contact your Biomed personnel regarding the continued safety of the unit before placing itback in operation. Do not spray cleaning agent on the chassis.Do not use disinfectants that contain phenol.Do not autoclave or clean ECS SI mPC or its peripherals with strong aromatic,chlorinated, ketone, ether, or other solvents, sharp tools or abrasives. Neverimmerse electrical connectors in water or other liquids.Attention!Ne pas immerger ou rincer ECS SI mPC ou ses périphériques. Si vous renversez par accident un liquide sur l'appareil, débranchez l'appareil de la source d'alimentation. Contactez votre Biomed concernant la sécurité continue de l'unité avant de la remettre en service. Ne pas pulvériser l'agent de nettoyage sur le châssis. Ne pas utiliser de désinfectants contenant du phénol. Ne pas passer à l'autoclave ou ECS SI mPC propre ou ses périphériques avec fortes, cétone, éther, ou d'autres solvants, des outils tranchants ou abrasifs aromatiques chlorés. Ne jamais plonger connecteurs électriques dans l'eau ou d'autres liquids.3 ECS SI mPC
Chapter 22 Getting Started
2.1 System TourBefore you start to set up system, take a moment to become familiar with thelocation sand purposes of the controls, drives, connections and ports, which areillustrated in the figures below.Figure 2.1 Top ViewFigure 2.2 Bottom ViewFigure 2.3 Side ViewWireless charger LED (Optional)(Power transfer Green blink, Fault Red blink)HDD LEDPowerButtonWireless charger/NFC (Optional)Speaker (Optional)Kensington Lock5 ECS SI mPC
ECS SI mPC 6USB 3.0 IR sensorUSB 2.0Combo Audio Jack (Mic In& Line out)DC JackHDMI RJ45 portThermal openingFigure 2.4 IO Side ViewInstall the VESA Mount
ECS SI mPC2.2 Distri ution DescriptionThe operating system is based on Windows .1 64bit / FreeDOS.2.3 owering the SystemConnecting a 12 adapter to the DC-In ack, the system will start up automatically.Figure 1: Location of DC-In ack. DC-In DC-In
Chapter 32ardware Installation
other oard Components3.1 other oard IntroductionECS SI mPC
a le o Mothe oa Co onentslo ia aBCOOTS1. FAN2.PWR BTN3.System FanSystem Fan4. BAT15. SPEAKER5. W CHG6.MiniPCIE.LED BAR.SATA.SATA PWR10.CLR CMOS11. NFC12.SODIMMSystem cooling fan connectorPower buttonBattery connectorSpeaker connectorWireless charger connectorLogo LED connector1 M.2 slot (half card supports mSATA, USB & PCIe signal)Serial ATA connectorSATA power connectorClear CMOS umperNFC connector204-pin DDR3 SDRAM SO-DIMM10ECS SI mPC
I/O orts1. Com o udio ac ic In ine OutUse the combo audio ack to connect the microphone, speaker or headphone.2. SB2. ortsUse the USB 2.0 ports to connect USB 2.0 devices.3. 4 ort4. D I ortConnect the display device to the HDMI port.. DC 12V acConnect the DC IN ack to the power adapter..CIIt is coustomer IR sensor..SB3. ortsD Status Descriptioncti ityDOFFNodataOrangeblinking ActiveinDOFFNolinkGreen LinkConnect an RJ-45 ack to the LAN port to connect your computer to the Network.LinkLEDECS SI mPC11Use the USB 3.0 ports to connect USB 3.0 devices.
12ECS SI mPC3.2 Installing the other oard1. Safety InstructionsFollow these safety precautions when installing the motherboard:Wear a grounding strap attached to a grounded device to avoid damage from staticelectricity.Discharge static electricity by touching the metal case of a safely grounded ob ect beforeworking on the motherboard.Leave components in the static-proof bags.Always remove the AC power by unplugging the power cord from the power outlet beforeor removing the motherboard or other hardware components.2. Installing the mother oard in a Chassis1. Aim four locating holes of the BTM-S motherboard.2. Use four screws to secure the motherboard.Do not over-Ɵghten the screws as this can stress the motherboard.
ECS SI mPC133. Installing ardwareInstallin Me o Mo ulesThis motherboard accommodates one memory module. It can support one 204-pin DDR3L 1333/1066 MH .Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.ou must install at least one module in any of the four slots. Total memory capacity is GB. Refer to the following to install the memory modules. Install the DIMM module into the slot and press it firmly down until it seats correctly. Check that the cutouts on the DIMM module edge connector match the notches in theDIMM slot.SODI
The slots on this motherboard are designed to hold expansion cards and connect them tothe system bus. Expansion slots are a means of adding or enhancing the motherboard’sfeatures and capabilities. With these efficient facilities, you can increase themotherboard’s capabilities by adding hardware that performs tasks that are not part ofthe basic system.ini CI Slot The mini PCI Express x1 slot is for extending usage which supports half-card, and it supportsmSATA, USB & PCIe signal.Before installing an add on card, check the documentation for the card carefully. If the card is not Plug and Play,you may have to manually configure the card before installation.Installin A on Ca s14ECS SI mPC
ECS SI mPC15This section explains how to set umpers for correct configuration of themotherboard.Conne tin tionaleiesRefer to the following for information on connecting the motherboard’s devices.Connect the system cooling fan to the FAN connector.1. F System cooling fan connector Che in u e Settin s
16ECS SI mPC3. S Spea er connector 2. B T1 Battery connector
ECS SI mPC14. C G ireless charger connector . D B ogo D connector
1ECS SI mPC. S T S T power connector. S T Serial T connector
ECS SI mPC198. NFC: NFC connector

Navigation menu