ELITEGROUP COMPUTER SYSTEMS WCPTI-S WPC Module User Manual Vector Smart Object

ELITEGROUP COMPUTER SYSTEMS CO., LTD WPC Module Vector Smart Object

User Manual

User GuideWPC ModuleWCPTI-SRDCHRGPDC4C5TP11JP2M8M6LED4R8RTVQRSDARSCLRQPDRGPUCSDACSCLCPA2TP10TP2TP9TP4TP5JP1OSCM3DVQRVQ2RVQ1RSINPRSINLC2TP8CDC2CDC1COM-CHVINRQOUT2RQOUT1CAIN0TP13TP15U3M4RLD1CAIN1TP16TP18M10U2RHD1CAPD1MOS_L2RS1RS2M7CADP4CADP3M1M5RCOILL2CCOILV2RQIN1RQIN2RCOILLRCOILHRREFH2RREFH1RREFHTUOXCTR CSORCOSC1CPACOSC2U1CBOOT2RTVINCVIN1CV33BCV33ATP1TP6MOS_L1MOS_H2MOS_H1 M9DTVINCADP2RVIN2RVIN3CBOOT1RH1CQOUT2RADCDCOILRPPHRPPGRPPENCADP5TP7M2RVIN18++2+40+BAEGND+CADCBDE15-KS3-051001WCPTI-S V:1.0RLED2RLED3RLED1CREFH1TP3TP12TP21TP20TP19C8C9CCLMPCADCRCLMPRVDLRVDL2MPCCOILVRVDHRL1RLD2RHD2CS1CS2CS3RH2RL2RSOUTU4CSINCSOUTCQOUT1DCLMP+
InterfaceRDCHRGPDC4C5TP11JP2M8M6LED4R8RTVQRSDARSCLRQPDRGPUCSDACSCLCPA2TP10TP2TP9TP4TP5JP1OSCM3DVQRVQ2RVQ1RSINPRSINLC2TP8CDC2CDC1COM-CHVINRQOUT2RQOUT1CAIN0TP13TP15U3M4RLD1CAIN1TP16TP18M10U2RHD1CAPD1MOS_L2RS1RS2M7CADP4CADP3M1M5RCOILL2CCOILV2RQIN1RQIN2RCOILLRCOILHRREFH2RREFH1RREFHTUOXCTR CSORCOSC1CPACOSC2U1CBOOT2RTVINCVIN1CV33BCV33ATP1TP6MOS_L1MOS_H2MOS_H1 M9DTVINCADP2RVIN2RVIN3CBOOT1RH1CQOUT2RADCDCOILRPPHRPPGRPPENCADP5TP7M2RVIN18++2+40+BAEGND+CADCBDE15-KS3-051001WCPTI-S V:1.0RLED2RLED3RLED1CREFH1TP3TP12TP21TP20TP19C8C9CCLMPCADCRCLMPRVDLRVDL2MPCCOILVRVDHRL1RLD2RHD2CS1CS2CS3RH2RL2RSOUTU4CSINCSOUTCQOUT1DCLMP+112233Charging Coil Power Cable(Black for Ground; Red for DC Input) LED Indicator
Dimension Transmier IC Charging Method Coil Type Operang TemperatureOperang Frequency86.0 mm x 60.0 mm x 6.1 mm Rohm, BD50720MWVMagnec InduconMP-A7(19V) 43.0 mm x 20.5 mm x 2.1 mm0~40 ˚C110K~205K The WCPTI-S is designed for wireless charger applicaon. It supports 5 and 15 wa receiver soluon. When WCPTI-S connects correctly to a PC, you need to place a supported charger device on the WCPTI-S, then you can see the indicator to show behavior. WCPTI-S has a few behavior to show status that you can check as below:Operation DescriptionSpecification
WCPTI-S LED behavior LED1: Green LED2: Blue LED3: Red RemarkON OFF OFFOFF ON OFFOFF OFF ONStandby OFF OFF OFFCharging-LOW Power Blinking OFF OFFBlinking 500msCharging-Middle Power OFF Blinking OFF Blinking 500msCharging Complete- Low Power ON OFF OFFCharging Complete- Middle Power OFF ON OFFError-1 FOD OFF OFF Blinking(0.2S)1.When Rx was removed, Tx cancel the error state2. 200msError-2 Power restricon- Low Power ON OFF Blinking(1S)1.When Rx was removed, Tx cancel the error state2. 1s3. Show orange LEDError-2 Power restricon- Middle Power OFF ON Blinking(1S)1.When Rx was removed, Tx cancel the error state2. 1s3. Show purple LEDError-3 OCP OTP… OFF OFF ON When Rx was removed, Tx cancel the error stateError-4 TSD OFF OFF ON When Rx was removed, Tx cancel the error stateG=500msB= 500msR= 500msPower on(G>B>R>OFF)Keep lighng unl 30 mins, then show standbystatus (If RX didn’t remove)LED Behavior
Notice and Safety Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.Declaration the Restriction of this Limited Module Approval:According to FCC Part 15 Subpart C Section 15.212, the radio elements of the modular transmitter must have their own shielding. However, due to there is no shielding for this Module, this module is granted as a Limited Modular Approval. When this Module is installed into the end product, a Class II Permissive Change or a New FCC ID submission is required to ensure the full compliance of FCC relevant requirements.10cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an opulation/uncontrolled environment can be satisfied.Only FCC approved antenna can be used for the module integrated into host.LABEL OF THE END PRODUCT:The final end product must be labeled in a visible area with the following" Contains TX FCC ID: WL6WCPTI-S". FCC Label Compliance Statement:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference(2) This device must accept any interference received, including interference that may cause undesired operation.
經型式認證合格之低功率輻射電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現干擾現象時，應立即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規作業之無線電通信。低功率 射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。NCC警語Golden Elite Technology ( SHENZHEN ) CO., LTD.Address: No.1, Nan-Huan Rd., ShaJing, BaoAn, Shenzhen, China

Navigation menu