ENTERMEDIA RX01-CC85A Wireless MIC receiver module User Manual
ENTERMEDIA CO., LTD. Wireless MIC receiver module Users Manual
Users Manual
RX01-CC85A Manual
Product Overview
1. Overview
• Wireless Receiver Module with TI CC8530
2. Specifications 사용 주파수
①Transmission : 2406~2474MHz
②Reception : 2406~2474MHz
③RF Power: 0.003 W/MHz
•Power: DC 5 V
•External Communication : UART 1CH.
•Audio CH: I2S 1CH.
Communication Interface
•UART Protocol
1) UART Interface
Baudrate : 9600BPS
Data : 8bit
Parity : None
2) Data framing
0xF3: Mic ON/OFF
0xF6: Mic1 Volume
0xD6: Mic2 Volume
0xE0: Mic Link Info
Approval Information
1 KCC
2 FCC compliance Information
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation
Including interference that may cause undesired operation. Modifications not expressly approved by the
manufacturer could void the user’s authority To operated the equipment under FCC rules. To satisfy FCC
exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter Module FCC ID : PBNRX01-CC85A
CAUTION : This device and its antenna(s) must not be co-located or operated in conjunction with any other
antenna or transmitter. End users cannot modify this transmitter device. Any unauthorized modification
could void the user’s authority to operate this device.
This module is limited to installation in mobile or fixed applications.
IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1)The transmitter module may not be co-located with any other transmitter or antenna,
2)OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain
change.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
Manual Information To the End User The OEM integrator has to be aware not to provide
information to the end user regarding how to install or remove this RF module in the
user’s manual of the end product which integrates this module. The end user manual
shall include all required regulatory information/warning as show in this manual.