ETi Solid State Lighting 9050102016 Motion Sensor User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3134973
Application ID	FpfnTA1YZq+xnFGbS6ncIw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.28kB (816044 bits)
Date Submitted	2016-09-14 00:00:00
Date Available	2016-09-18 00:00:00
Creation Date	2016-09-01 10:22:31
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2016-09-13 17:02:47
Document Title	Microsoft Word - Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	hp

Item/unit
Operating voltage
Switched power
Standby power
Warmming-up time
Detection area
Hold time
Daylight threshold
Microwave frequency
Microwave power
Detection range
Detection angle
Mounting height
Operating temperature
IP rating
Certificate
Parameter
120V /60Hz
200W (capacitive)
<0.5w
20s
10%/50%/75%/100%, can be customized
5S/90S/5min/15min, can be customized
2~50lux disable
5.79GHz
5.8GHz+/-75MHz
<1mw
Max. (oxH): 10m x 6m
30°～150°
Max.6m
-20°C～70°C
IP20
ETL FCC
In the end we will only need English and Spanish for the US. We will do a separate Spanish
IM. The IM for the motion wrap is included. Refer to that so we are telling the same story
with regard to personally adjusting the sensor. This is not an easy concept for many people
to grasp so you have to keep asking yourself as you write these “can I understand it simply”?
Deb can you put your marketing expertise on this after the next draft?
Motion Sensor Settings
You can adjust the settings for detection area, hold time and daylight sensitivity
should you wish to. The sensor comes factory pre‐set at the most popular settings. To
adjust you’ll need to simply move the dip switches according to the setting you
desire. Please refer to the table below.
Installation Options
This sensor is designed to work with both select linkable plug in fixtures and also with both
LED and Fluorescent fixtures that utilize a direct wire connection method.
1. Mounting inline to a linkable LED fixture
a. Turn power off
b.
The sensor will mount between your power cord end and the fixture. (the
drawing goes here)
The sensor notes which end is power In and which is power Out (show
drawing of both here)
Power in:
c.
Power out:
d.
Use the small male to male connector provided to make the connection on
the power out end of the sensor by inserting it. Once the connector is in
the sensor simply push it into the power end of the fixture (show drawing
here)
e.
Next simply insert the power cord to the power in end of the
sensor. Make sure both connections fit securely
f.
2.
Turn the power on. Make sure the pull chain is in the on position
Mounting via Direct Wiring method
a. Turn power off
b. Determine which size knockout is required. Our sensor comes with 2
convenient sizes (3/4” and ½”) (double check with Houshengmin)
c.
Use only the lock nut for that size
d. Prepare the fixture by removing the lens if needed and then remove the
knockout where you wish to mount the sensor.
e. Follow the wiring diagram below (add wiring diagram)
by making the connection with the wire nuts provided . Important to note there that the
lock nut should be on the inside of the fixture wall with the wires coming through the middle
(insert drawing here) (no wire nuts in my sample you sent, please add to cover all wires)
f. Once the connections are made insert the threaded end into the hole
completely and tighten the lock nut down by hand. For a firm fit gently use
pliers to snug the lock nut down
g. Replace the lens if needed.
h. Turn power on
Trouble Shooting Section Needed
Add tips here
•
FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is
subjected to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IC Compliance Statement: This device complies with Industry Canada’s licence‐exempt
RSSs.Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent
causer un mauvais fonctionnement de l'appareil.
Changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2016:09:01 10:22:31+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2016:09:13 17:02:47+08:00
Metadata Date                   : 2016:09:13 17:02:47+08:00
Format                          : application/pdf
Creator                         : hp
Title                           : Microsoft Word - Manual
Document ID                     : uuid:c72006f1-de92-4416-b809-292cb005a4d4
Instance ID                     : uuid:994f990b-a2cc-433d-9d88-5f1330a90fbe
Page Count                      : 5
Author                          : hp

EXIF Metadata provided by EXIF.tools