EUROTECH RFID13 RFID Module User Manual RFID13 R01 datasheet

EUROTECH SpA RFID Module RFID13 R01 datasheet

Users Manual

Dat as h eet RFID1 3 R0 1 1 3 .5 6 MH z Mu l t is t an dar d RFID t r an s c eiv er mo d u l e f o r Zypad WL1 x1 x ETH_RFID13 R01_DS220507 Eu r o t ec h S.p.A. e-mail : s al es @eu r o t ec h .it h t t p://www.eu r o t ec h .it Introduction The module is a multistandard RFID transceiver for use with the Zypad WL1x1x wearable computer family. It works at 13.56 MHz and supports the following standards: ISO 14443A, ISO 14443B and ISO 15693. The interface with the Zypad main unit is made through the serial port COM2. FCC information and compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Instruction manual for FCC ID labeling Module type: <RFID Transceiver Module> RFID 13 FCC-ID : UKMRFID13 This intends to inform you how to specify the FCC ID of our <RFID Transceiver Module> Module RFID13 on your final product. Based on the Public Notice from FCC, the product into which the our transmitter module is installed must display a label referring to the enclosed module. Example of label: “Contains FCC ID: UKMRFID13” Main features SMT (Surface Mount Technology) connections Firmware upgradeable via serial interface Possibility to connect an external SAM (Secure Access Module)
RFID1 3 R0 1 D at as h eet ETH_RFID13 R01_DS220507 EuroTecH SpA a member of the Eurotech Group Via Fratelli Solari, 3/a 33020 Amaro (UD) - Italy E-mail: sales@eurotech.it Tel. +39 0433 485 411 - Fax. +39 0433 485 499 Note: The information in this document is subject to change without notice and should not be construed as a commitment by EuroTecH S.p.A. While reasonable precautions have been taken, EuroTecH S.p.A. assumes no responsibility for any error that may appear in this document. All trademarks or registered trademarks are the properties of their respective companies. DIGITAL TECHNOLOGIES FOR A BETTER WORLD www.eurotech.it Electrical features Parameter Value Notes Input power supply +3.3 Vdc @ 100mA (max) Serial interface line +3.3 Vdc Serial communication characteristics: Bit per second: 115200 Parity: None Data bits: 8 Stop bits: 1 Stand by input line +3.3 Vdc Active low signal Hardware reset input line +3.3 Vdc Active low signal Block diagram Main connections Stand by Input (3.3 Vdc level) Reset Input (3.3 Vdc level) ATMEL AT91SAM7S64 Microprocessor Connector to SAM Module SAM Module Interface 13.56 MHz RF Interface 13.56 MHz PCB Antenna Serial Interface (3.3 Vdc level) Step up 3.3 Vdc - 5 Vdc 3.3 Vdc 5 Vdc
Tec h n ic al D at as h eet L MS -Zypad -1 x 1 x 1 3 .5 6 MH z Mul t is t an d ar d RFI D t r an s c eiv er f o r Zypad WL 1 x 1 x ETH_LMS-Zypad-1x1x_TDS220507 Eur o t ec h S .p.A. e-mail : s al es @eu r o t ec h .it h t t p://www.eur ot ec h .it Functional description The device reads and writes transponders at a frequency of 13.56 MHz and supports the ISO 14443A, ISO14443B and ISO 15693 standards. The microprocessor is an ARM ATMEL AT91SAM7S64. The RF interface is based on the PHILIPS CLRC632 ‘Multiple contactless reader IC’ controller. The SAM interface is formed by the ON NCN4555 ‘SIM card power supply / level translator’ circuit. The power voltage is 3.3 Vdc and is used to supply the digital devices (such as: microprocessor and I/O). An internal MAX1724 DC/DC step-up converter allows you to obtain a +5V voltage to supply RF devices. A 1.8 Vdc voltage regulator is integrated inside the microprocessor and supplies the ARM core. The RF antenna is integrated on the PCB (Printed Circuit Board) of the module. The reset signal operates at a hardware level. The stand by signal is managed at a firmware level. The following table lists the supported tags: Tag Made by Standard Uid length MIFARE 1k Philips 14443A 4 bytes MIFARE 4k Philips 14443A 4 bytes MIFARE ultralight Philips 14443A 7 bytes ICODE2 Philips 15693 8 bytes TAG-IT HF-I Texas 15693 8 bytes EM4135 MEM 15693 8 bytes LRI64 / LRI512 ST 15693 8 bytes SR176 ST 14443B 8 bytes The following table lists the interfacing signals: Signal Description WL1x1x signal +3.3 Vdc Input power supply VDD GND Ground signal GND IN1 Stand by input (active low signal) GPIO IN2 Reset input (active low signal) RESET GND Ground signal GND RX Serial Input (3.3 Vdc line) TX TX Serial Output (3.3 Vdc line) RX

Navigation menu