EUROTECH RFID13 RFID Module User Manual RFID13 R01 datasheet

Download:
Mirror Download [FCC.gov]
Document ID	887641
Application ID	MBL8USGuJBiZMcYgLfmcCQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.51kB (318847 bits)
Date Submitted	2008-01-10 00:00:00
Date Available	2008-01-10 00:00:00
Creation Date	2007-10-25 06:44:13
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2007-10-25 06:44:13
Document Title	RFID13 R01 datasheet
Document Creator	Microsoft® Office Word 2007
Document Author:	Andrea Cargnelutti

D at as h eet
RFID 1 3 R0 1
1 3 .5 6 MH z Mu l t is t an d ar d RFI D t r an s c eiv er mo d u l e f o r Zypad WL 1 x 1 x
Introduction
The module is a multistandard RFID transceiver for use with
the Zypad WL1x1x wearable computer family. It works at
13.56 MHz and supports the following standards: ISO
14443A, ISO 14443B and ISO 15693.
The interface with the Zypad main unit is made through the
serial port COM2.
FCC information and compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Instruction manual for FCC ID labeling
Module type:  RFID 13
FCC-ID
: UKMRFID13
This intends to inform you how to specify the FCC ID of our < RFID Transceiver Module> Module RFID13 on your
final product.
Based on the Public Notice from FCC, the product into which the our transmitter module is installed must
display a label referring to the enclosed module.
Example of label: “Contains FCC ID: UKMRFID13”
Main features
SMT (Surface Mount Technology) connections
Firmware upgradeable via serial interface
Possibility to connect an external SAM (Secure Access Module)
Eu r o t ec h S .p.A .
e-mail : s al es @eu r o t ec h .it
h t t p://www.eu r o t ec h .it
ETH_RFID13 R01_DS220507
RFI D 1 3 R0 1 D at as h eet
Electrical features
Parameter
Value
Input power supply
+3.3 Vdc @ 100mA (max)
Notes
Serial interface line
+3.3 Vdc
Serial communication characteristics:
Bit per second: 115200
Parity:
None
Data bits:
Stop bits:
Stand by input line
+3.3 Vdc
Active low signal
Hardware reset input line
+3.3 Vdc
Active low signal
Block diagram
Main connections
Stand by
Input
(3.3 Vdc level)
Reset
Input
(3.3 Vdc level)
Serial
Interface
(3.3 Vdc level)
ATMEL
AT91SAM7S64
Microprocessor
Connector
to SAM
Module
SAM
Module
Interface
Step up
3.3 Vdc - 5 Vdc
3.3 Vdc
13.56 MHz
RF Interface
EuroTecH SpA
a member of the Eurotech Group
Via Fratelli Solari, 3/a
33020 Amaro (UD) - Italy
E-mail: sales@eurotech.it
Tel. +39 0433 485 411 - Fax. +39 0433 485 499
5 Vdc
13.56 MHz
PCB
Antenna
DIGITAL TECHNOLOGIES FOR A BETTER WORLD
www.eurotech.it
Note: The information in this document is subject to change without notice and should not be construed as a commitment by EuroTecH S.p.A.
While reasonable precautions have been taken, EuroTecH S.p.A. assumes no responsibility for any error that may appear in this document.
All trademarks or registered trademarks are the properties of their respective companies.
ETH_RFID13 R01_DS220507
Tec h n ic al D at as h eet
L MS -Zypad -1 x 1 x
1 3 .5 6 MH z M u l t is t an d ar d RFI D t r an s c eiv er f o r Zypad WL 1 x 1 x
Functional description
The device reads and writes transponders at a frequency of 13.56 MHz and supports the ISO 14443A, ISO14443B and
ISO 15693 standards.
The microprocessor is an ARM ATMEL AT91SAM7S64.
The RF interface is based on the PHILIPS CLRC632 ‘Multiple contactless reader IC’ controller.
The SAM interface is formed by the ON NCN4555 ‘SIM card power supply / level translator’ circuit.
The power voltage is 3.3 Vdc and is used to supply the digital devices (such as: microprocessor and I/O). An internal
MAX1724 DC/DC step-up converter allows you to obtain a +5V voltage to supply RF devices. A 1.8 Vdc voltage
regulator is integrated inside the microprocessor and supplies the ARM core.
The RF antenna is integrated on the PCB (Printed Circuit Board) of the module.
The reset signal operates at a hardware level.
The stand by signal is managed at a firmware level.
The following table lists the supported tags:
Tag
MIFARE 1k
MIFARE 4k
MIFARE ultralight
ICODE2
TAG-IT HF-I
EM4135
LRI64 / LRI512
SR176
Made by
Philips
Philips
Philips
Philips
Texas
MEM
ST
ST
Standard
14443A
14443A
14443A
15693
15693
15693
15693
14443B
Uid length
4 bytes
4 bytes
7 bytes
8 bytes
8 bytes
8 bytes
8 bytes
8 bytes
The following table lists the interfacing signals:
Signal
+3.3 Vdc
GND
IN1
IN2
GND
RX
TX
Description
Input power supply
Ground signal
Stand by input (active low signal)
Reset input (active low signal)
Ground signal
Serial Input (3.3 Vdc line)
Serial Output (3.3 Vdc line)
Eu r o t ec h S .p.A.
e-mail : s al es @eu r o t ec h .it
h t t p://www.eu r o t ec h .it
WL1x1x signal
VDD
GND
GPIO
RESET
GND
TX
RX
ETH_LMS-Zypad-1x1x_TDS220507

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Language                        : it-IT
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Office Word 2007
Title                           : RFID13 R01 datasheet
Creator                         : Andrea Cargnelutti
Creator Tool                    : Microsoft® Office Word 2007
Create Date                     : 2007:10:25 06:44:13Z
Modify Date                     : 2007:10:25 06:44:13Z
Document ID                     : 56B35AD9-2A2D-408F-AEB6-A72F49552F7E
Instance ID                     : 56B35AD9-2A2D-408F-AEB6-A72F49552F7E
Part                            : 1
Conformance                     : B
Author                          : Andrea Cargnelutti

EXIF Metadata provided by EXIF.tools