Echometer WS Echometer Wireless Sensor User Manual WS User Guide
Echometer Company Echometer Wireless Sensor WS User Guide
User Manual
Wireless Sensor User Guide Scope: This manual pertains to the products listed in Table 1 below. Associated FCC and IC identification numbers are listed, as well as page number for the specific sensor’s installation instructions. Table 2 includes the FCC Label design and intended installation location. Sensor Model # : Description FCC ID IC ID WPRT: Wireless Polished Rod Transducer WHT: Wireless Horseshoe Transducer WHT50K: Wireless Horseshoe Transducer - 50,000 pounds Q5Q-WS 10048A-WS WPT: Wireless Pressure Transducer WGDA: Wireless General Data Acquisition Table 1 All of the above utilize the same electronic PCB, Antenna, Battery, and run the same Firmware. The PCB in each case is packaged in a fully enclosed stainless steel enclosure. Each model includes a different transducer element wired to the PCB (such as a strain gauge, or thermistor). The instructions and pictures below depict the WPRT model. All other models will be similar except for differences in the physical form factor. Table 2 The Wireless Sensors are components of the Echometer Well Analyzer and designed to be used with the Echometer WB100 Wireless Base, providing a wireless option for obtaining data, (such as dynamometer, power and pressure/temperature). The data is analyzed by the Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 Wireless Sensor User Guide Echometer TAM software which runs on a PC/Notebook and utilized to provide analysis of well performance. Please refer to the Echometer TAM Software User Manual for instructions specific to software operation and to the Echometer WB100 Wireless Base User Manual for instructions specific to that device. • • • • • WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s expense. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the antenna and your body. This Class digital apparatus complies with Canadian ICES-003. (Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada) This device has been designed to operate with the antennas listed below. The specific models listed or substitutes as specified below may be used. o Pulse W1030 o Linx Tech ANT-2.4-CW-RAH-RPS: 2.4GHz o Substitutes may be used, as long as they meet the 2.4GHz, 50Ω, <=2dBi gain, RPSMA Male requirements. Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 Wireless Sensor User Guide WPRT Installation: 1. Clamp the Wireless Polished Rod Transducer (WPRT) to the polished rod on the oil well below the carrier bar. 2. Install the antenna as shown. It is desirable that the antenna be pointed upwards during operation. 3. Press the Power button on the WPRT as indicated below: a. The LED above the Power button will proceed with the LED test, (illuminating three green, and then three red LEDs). b. Following the LED test, the Power button LED will flash a maximum of ten times in rapid succession to indicate battery power. A fully charged battery will flash ten times, with fewer flashes as the battery charge drops. Recharge the battery when the flashes reduce to two. c. Following the battery test, the Power LED will flash once per second to indicate the WPRT is ready to proceed. 4. Press the Install button as shown below: a. The Install LED will flash RED if the WPRT it too tight or flash GREEN if it is too loose. Tighten or loosen the knob as needed until the LED illuminates solid green. Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 Wireless Sensor User Guide 5. Press the Acquire button as shown below to initiate data acquisition. Use the TAM software and instructions to complete the test. Pressing ACQUIRE again will stop acquisition. 6. To turn off the WPRT, simply press the Power button for two seconds. Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 4 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:f553f179-0992-11e2-0000-f9ac2be0b5e3 Producer : GPL Ghostscript 9.05 Keywords : () Modify Date : 2012:09:25 12:35:48-05:00 Create Date : 2012:09:25 12:35:48-05:00 Creator Tool : PDFCreator Version 1.5.0 Document ID : uuid:f553f179-0992-11e2-0000-f9ac2be0b5e3 Format : application/pdf Title : WS User Guide Creator : daraius Description : () Author : daraius Subject :EXIF Metadata provided by EXIF.tools