Ecolink Intelligent Technology BHAWS001 Ring Flood/Freeze Sensor User Manual Ring Video Doorbell Setup and Installation Guide
Ecolink Intelligent Technology, Inc. Ring Flood/Freeze Sensor Ring Video Doorbell Setup and Installation Guide
Users Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This device complies with Industry Canada’s licence-exempt RSSs. Operation
is subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
CAN ICES-3 (B)/NMB-3(B) – This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
The FCC ID of the device in this package can be found on the back or bottom
of the device.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the
same of equivalent type recommended by the manufacturer. Dispose of the
used batteries according to the manufacturer’s instructions.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
1523 26th St.
Santa Monica, CA 90404
Ring_Flood_Freeze_Sensor_legal.indd 1 4/12/18 2:26 PM
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Protect the device from direct sunlight. Install the device at dry locations, and
protect it against rain and humidity. The device may not get in contact to salt
water or other conductive liquids. The device must be charged only within a
building in a dry state.
This device may not be disassembled and used for any other purpose. This
unit, and all the components are configured for the sole purpose of providing
a security system. They are not approved for individual cellular use, battery use
or other mishandling.
A mobile app must be used to set up the device.
This device is not an Access point or Hotspot and should not be used as one.
To review your warranty coverage, please visit www.ring.com/warranty.
Patents: www.ring.com/patents
Version 1.1
Ring_Flood_Freeze_Sensor_legal.indd 2 4/12/18 2:26 PM
Prevent water and ice damage
at home.
Ring Flood/Freeze Sensor is a smart
sensor for your Ring Alarm system. Place
it anywhere that flooding or freezing
conditions can occur.
When the Sensor detects water or
dangerously low temperatures (around
40 ° F or 4.4 ° C), Ring Alarm notifies you
of the problem, wherever you are.
Contents
1. Diagram
2. In-app Setup
3. Pairing the Sensor
4. Physical Installation
5. Additional Information
Diagram Begin the setup process near
your Ring Alarm Base Station.
In the Ring app, tap Set Up a Device.
Choose Security Devices, then Sensors,
then Ring Flood/Freeze Sensor, then tap
Add Device.
To complete the setup process, follow
the in-app instructions.
When prompted, scan the QR
Code or enter the PIN.
This begins the pairing process. The QR
Code and PIN are on the back of your
sensor and in the product packaging.
For Ring Alarm
1.
Say hello to
your Ring
Flood/Freeze
Sensor.
2.
Set up your
Ring Flood/
Freeze Sensor
in the Ring app.
3.
Pair your Ring
Flood/Freeze
Sensor with
your Ring Base
Station.
LED Ring
Setup Button
Flood Sensors
Flood/Freeze Sensor
Watch your Sensor connect.
As your Sensor pairs to your Base Station,
its LED ring blinks slowly, then quickly.
Once the Sensor is paired, the LED glows
blue for three seconds.
Place the Sensor on the ground.
Choose a spot next to a possible source
of flooding, such as your water heater,
sink, or refrigerator. Take care to place
the Sensor in a location where it won’t be
kicked or moved unintentionally.
Close the lid.
Place the lid back on the Sensor, taking
care to line up the semi-circle on the rim
of the lid with the “open” semi-circle on
the base. Twist the lid clockwise to lock
it in.
How to remove this Sensor from
your system:
Open the side menu in the Ring app and
tap Devices, then Base Station. Next,
select your Sensor, then tap the gear-
shaped icon, and tap Remove Device.
When prompted, open the sensor and
remove and reinstall the battery to
complete the removal.
How to perform a factory reset:
If your Flood/Freeze Sensor stops
working or can’t connect (even with a
good battery), try a factory reset.
To do this, press and hold the Setup
button for 10 seconds. When the LED
ring stops blinking, the Sensor has reset.
How to replace the battery:
Twist the lid on the Sensor counter-
clockwise and lift to remove. Replace the
battery with a fresh CR123A cell.
The Sensor then reconnects to your Ring
Base Station automatically.
LED status patterns:
Open the lid and pull out the tab.
Twist the lid to the left to unlock, then lift it
to remove. Next, pull out the clear battery
tab. This turns on the Sensor.
Your Base Station finds it automatically.
Test your Flood/Freeze Sensor.
Bring your Sensor to the area you want to
monitor.
Push the Setup button inside the Sensor
to test the connection. If the LED ring
blinks blue, the Sensor has connected
successfully and is ready to place.
If it blinks red, try the test again. You may
find that repositioning the Sensor (even
just a few inches) can improve reception
and allow it to reconnect. Blue Blink (1x)
Water or low
temperature
detected
Red Blinks (3x)
Sensor
opened
or moved
4.
Place your Ring
Flood/Freeze
Sensor.
5.
Additional
information.
© 2018 Ring LLC or its affiliates.
RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates.
Last updated: 09/26/18
Setup
Button If the Sensor cannot connect, try installing a
Ring Range Extender between your Sensor
and Base Station, following the included
instructions.
If the Sensor does not pair successfully,
the LED ring glows red. To try the pairing
process again, remove and reinstall the
battery inside the Sensor.
This process disconnects the Sensor from
your Alarm Base Station. To begin using the
Sensor again, set it up in the Ring app.
Blue & Red Blinks
Firmware
updating