Edgecore Networks ECW7211L 802.11ac Cloud-based Indoor Dual Band Enterprise Acess Point User Manual Quick Start Guide
Edgecore Networks Corporation 802.11ac Cloud-based Indoor Dual Band Enterprise Acess Point Quick Start Guide
Contents
User Manual
Quick Star t Guide 802.11ac Cloud-based Indoor Dual Band Enterprise Acess Point ECW7211-L The ECW7211-L AP includes its own built-in features for mounting the unit to a wall or suspended ceiling T-rail. Note: For Safety and Regulatory information, refer to the Safety and Regulatory Information document included with the AP. Caution: The planning and installation of the AP requires professional personnel that are trained in the installation of radio transmitting equipment. The user is responsible for compliance with local regulations concerning items such as antenna power, use of lightning arrestors, grounding, and radio mast or tower construction. Therefore, it is recommended to consult a professional contractor knowledgeable in local radio regulations prior to equipment installation. Follow these steps to install the AP: 1. Unpack the AP Unpack the AP and check the package contents. ◆ ◆ ◆ ◆ ◆ ◆ www.edge-core.com 802.11a/ac/b/g/n Wireless Access Point AC power adapter Console cable Ceiling-mount accessory Four adhesive foot pads Documentation — Quick Start Guide (this guide) and Regulatory and Safety Information – 1 – E012015-AP- R01 150200001031A Quick Start Guide 2. Mount the AP After planning your installation, mount the unit on a wall or suspended ceiling T-rail. Mounting on a Wall Set two screws in the wall 116 mm (4.57 in.) apart. Slide the AP’s wall mounting slots down onto the screws so that the unit is secure. Mounting on a Ceiling T-rail Position the ceiling-mount accessory clip holders on either side of the T-rail. Turn the ceiling-mount accessory until the two clips lock it to the T-rail. Slide the base of the AP onto the T-rail accessory until it is locked in place. NOTE: The ceiling m ount ing plat e support s t wo different kinds of ceiling bars. The posit ion illust rat ed above is for 15 m m bars. Use t he ot her posit ion at a 90 degrees angle for 24.5 m m bars. – 2 – Quick Start Guide 3. Connect Cables Connect network cable to the Eth0/PoE 1000BASE-T RJ-45 port for your network connection. The Etho/PoE port connection can also provide PoE power to the unit. (Optional) Connect a local LAN switch or computers to the LAN1 and LAN2 100BASE-TX RJ-45 ports. Connect Category 5e or better cable to the Eth0/PoE RJ-45 port. 4. Connect Power If you do not power the unit using PoE, connect the AC power adapter to the AP and to an AC power source. Connect the power adapter to the power socket on the AP. Plug the power adapter into a nearby AC power source. – 3 – Quick Start Guide 5. Verify AP Operation Verify basic AP operation by checking the system LEDs. The WAN LED and any connected LAN port LEDs should light up green. The circular LED on the top panel should light up green and blue to indicate 2.4 GHz and 5 GHz radio operation respectively. Power Eth1 Eth0/PoE Radio — LED2.4 G / 5 GHz 6. Connect to the Web The AP offers a user-friendly web-based management interface for the User Interface configuration of all the unit’s features. You can make initial configuration changes by connecting a PC directly to the AP’s LAN port. The AP has a default management IP address of 192.168.1.1 and a subnet mask of 255.255.255.0. You must set your PC IP address to be on the same subnet as the AP (that is, the PC and AP addresses must both start 192.168.1.x). Log in to the web interface using the default settings: ◆ ◆ Login Name — root Password — admin123 For more information on AP configuration using the web interface, refer to the Management Guide, which is on the Edge-Core web site, www.edge-core.com. – 4 – Quick Start Guide Hardware Specifications Item Specification Chassis Size (W x D x H) 200 x 200 x 36.5 mm (7.87 x 7.87 x 1.44 inch) Weight 750 g (1.65 lb) Temperature Operating: 0 °C to 45 °C (32 °F to 113 °F) Storage: -40 °C to 70 °C (-40 °F to 158 °F) Humidity Operating: 5% to 95% (non-condensing) Network Interfaces Ports Eth0/PoE RJ-45 Port: 1000BASE-T, PoE+ PD Eth1 RJ-45 Ports: 1000BASE-TX 2.4 GHz Radio IEEE 802.11b/g/n 5 GHz Radio IEEE 802.11a/ac/n Radio Frequencies 2412 ~ 2472 MHz (ETSI), 2412 ~ 2462 MHz (FCC) 5745 ~ 5825 MHz (China) 5180 ~ 5240 MHz (ETSI), 5180 ~ 5240 MHz, 5745 ~ 5825 MHz (FCC) Power Supply PoE Input Power 48 VDC, 0.6 A AC Power Adapter AC Input: 100 ~ 240 VAC DC Output: 12 VDC, 2.5 A Power Consumption 22.5 W maximum Regulatory Compliances Radio EN 300 328 V1.8.1:2012 (2012-06) EN 301 893 V1.7.1:2012 (2012-06) FCC Part 15C 15.247/15.207 (2.4-2.4835GHz) FCC Part 15E 15.407 (5.150GHz-5.250GHz, 5.725-5.850GHz) Emissions EN 55022 2010/ AC: 2011, Class B FCC Part 15 Subpart B, Class B ICES-003, Issue 5, Class B Immunity EN 55024 : 2010 EN 301 489-1 V1.9.2 (2011-09), Class B EN 301 489-17 V2.2.1 (2012-09) AS/NZS CISPR 22: 2009/Amdt 1: 2010, Class B Safety UL (CSA 22.2 No. 60950-1 & UL60950-1) CB (IEC/EN60950-1) – 5 –
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : angel_peng Create Date : 2009:04:28 17:46:20Z Modify Date : 2015:02:10 19:07:25+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : Quick-Start-Guide.fm Creator : angel_peng Creator Tool : FrameMaker 9.0 Metadata Date : 2015:02:10 19:07:25+08:00 Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:a2adbda8-baf3-4a08-b0ba-2baac5999eb1 Instance ID : uuid:78d8da61-87da-4017-b411-73c0d329233e Page Mode : UseNone Page Count : 5EXIF Metadata provided by EXIF.tools