Edgecore Networks WAP5110 IEEE 802.11a/b/g/n Enterprise Access Point User Manual Quick Start Guide

Edgecore Networks Corporation IEEE 802.11a/b/g/n Enterprise Access Point Quick Start Guide

User Manual (WAP5110).pdf

– 1 –Quick Start GuideIEEE 802.11a/b/g/n Enterprise Access PointWAP5110NOTE: For detailed access point (AP) installation information, refer to the Installation Guide, which is on the Documentation CD included with the AP.NOTE: For Safety and Regulatory information, refer to the Safety and Regulatory Information document included with the AP.Installation InformationThe AP includes its own built-in features for mounting the unit to a wall or suspended ceiling T-rail. Caution: The planning and installation of the AP requires professional personnel that are trained in the installation of radio transmitting equipment. The user is responsible for compliance with local regulations concerning items such as antenna power, use of lightning arrestors, grounding, and radio mast or tower construction. Therefore, it is recommended to consult a professional contractor knowledgeable in local radio regulations prior to equipment installation.Follow these steps to install the AP:1. Unpack the AP Unpack the AP and check the package contents.◆WAP5110 Enterprise Access Point◆AC Power adapter◆Console cable (RJ-45 to DB-9)◆Quick Start Guide (this guide)◆Regulatory and Safety Information◆Documentation CD — includes Installation Guide and Management GuideE042013-CS-R01150200000556Awww.smc.com
Quick Start Guide– 2 –2. Mount the AP After planning your installation, mount the unit on a wall or suspended ceiling T-rail. .Mounting on a WallSet two screws in the wall 6.2 mm (2.4 in.) apart.Slide the AP’s wall mounting slots down onto the screws so that the unit is secure.121212.Mounting on a Ceiling T-railPosition the AP’s ceiling-mount clip holders on either side of the T-rail.Turn the AP until the two clips lock the AP to the T-rail.12
Quick Start Guide– 3 –3. Connect Cables Connect network cable to the RJ-45 port for your network connection. The RJ-45 port connection can also provide PoE power to the unit.4. Connect Power If you do not power the unit using PoE, connect the AC power adapter to the AP and to an AC power source.Connect Category 5e or better cable to the RJ-45 port.11Connect the power adapter to the power socket. Connect the power adapter to a nearby AC power source.1212
Quick Start Guide– 4 –5. Verify AP Operation Verify basic AP operation by checking the system LEDs. The Power LED should be on green and the Network LED on or flashing amber. 6. Connect to theConsole PortTo make initial configuration changes to the AP, connect a PC to the AP’s console port using the included console cable. Network Link/ActivityPower/Diagnostic2112Console Port11
Quick Start Guide– 5 –From a PC running VT-100 terminal emulator software, use the following settings:◆Baud rate — 115,200 bps◆Character Size — 8 Characters◆Parity — None◆Stop bit — One◆Data bits — 8◆Flow control — noneLog in to the command-line interface (CLI) using default settings:◆Login Name — admin◆Password — null (there is no default password)For information on AP configuration and CLI commands, refer to the Management Guide, which is on the Documentation CD included with the AP.
Quick Start Guide– 6 –Hardware SpecificationsItem SpecificationChassis SpecificationsSize W x D x H: 140 x 140 x 47.8 mm (5.51 x 5.51 x 1.88 inches)Weight 500 g (1.10 lbs)Temperature Operating: 0 °C to 40 °C (32 °F to 104 °F)Storage: -20 °C to 70 °C (-4 °F to 158 °F)Humidity Operating: 5% to 95% (non-condensing)Network InterfacesPorts One RJ-45 Port: 1000BASE-T, PoE (PD)2.4GHz Radio IEEE 802.11b/g/n5 GHz Radio IEEE 802.11a/nRadio Frequencies 2400 ~ 2483.5 MHz2412 ~ 2472 MHz5745 ~ 5825 MHz (China)5180 ~ 5320 MHz (ETSI)5500 ~ 5700 MHz (ETSI)Power Supply SpecificationsPoE Input Power 48 VDC, 0.3AAC Power Adapter AC Input: 100 ~ 240 VACDC Output: 12 VDC, 2 APower Consumption 22.5 W maximumRegulatory CompliancesRadio ETSI 300 328 (802.11b/g)ETSI 301 893 (802.11a Full range)ETSI 301 489 (DC power)FCC Part 15C 15.247/15.207 (2.4-2.4835GHz, 5.725-5.850GHz)FCC Part 15E 15.407 (5.150GHz-5.250GHz)NCC LP0002 (2.4-2.4835GHz, 5.250-5.350GHz, 5.725-5.850GHz)Emissions EN 55022:2007, Class A/BIEC 61000-3-2/3FCC Class B Part 15CNS13438Immunity EN 55024:2001 + A2:2003IEC 61000-4-2/3/4/5/6/8/11Safety CSA c us (CSA/UL60950-1)CB (IEC60950-1)

Navigation menu