Edimax Technology Co 9572060708 Wireless LAN Access Point User Manual
Edimax Technology Co Ltd Wireless LAN Access Point Users Manual
Users Manual
Wireless LAN Access Point IEEE 802.11b/g 54Mbps User’s Manual Table of Contents Chapter 1 Introduction............................................................................. 1 1.1 1.2 1.3 1.4 Package Contents .......................................................................................... 2 Features ......................................................................................................... 2 Specifications ................................................................................................ 2 Physical Description ..................................................................................... 3 Chapter 2 Wireless LAN Access Point Connection................................ 5 Chapter 3 Wireless LAN Access Point Configuration ........................... 6 3.1 Getting Started .............................................................................................. 6 3.2 Configuring the Access Point ..................................................................... 11 3.2.1 Status and Information .......................................................................................12 3.2.2 Wireless Setting .................................................................................................13 3.2.3 Advanced Setting ...............................................................................................27 3.2.4 Security ..............................................................................................................30 3.2.5 MAC Address Filtering......................................................................................38 3.2.6 System Utility ....................................................................................................40 3.2.7 Configuration Tool.............................................................................................44 3.2.8 Firmware Upgrade .............................................................................................46 3.2.9 Reset...................................................................................................................47 Chapter 4 Troubleshooting .................................................................... 48 Introduction Chapter 1 Introduction This product is an access point for IEEE 802.11g/b 2.4GHz wireless networks. You can use this access point to build a wireless LAN. Any wireless LAN station can join the wireless network by using the “Infrastructure Mode”. The product supports WEP, WPA, ESSID and MAC address filter functions to consolidate the wireless network security. With ESSID authentication, 64/128 bit WEP encryption and MAC address filtering you can prevent unauthorized wireless stations from accessing your wireless network. This product provides an easy to use user interface and allows users to configure from a standard web browser. Also it includes a DHCP server to provide multiple wireless and wired users to get their IP address automatically. With versatile features, this product is the best choice for you to integrate your wireless and wired network seamlessly. Introduction 1.1 Package Contents The Access Point includes the following items: y One Access Point y One Power Adapter y One User’s Manual 1.2 1.3 Features Complies with the IEEE 802.11b/g (DSSS) 2.4GHz specification. High data rate 54Mbps network speed. Seamlessly integrate wireless and wired Ethernet LAN networks. Auto rate fallback in case of obstacles or interferences. Provide 64/128-bit WEP and WPA Data Encryption functions to protect the wireless data transmissions. Built-in DHCP server supports auto IP addresses assignment. Supports Web-based configuration. Specifications Standards: IEEE 802.11b/g (Wireless), IEEE 802.3 (Wired) Data Rate: 54/48/36/24/18/12/11/9/6/5.5/2/1Mbps auto fallback Security: 64/128-bit WEP and WPA Data Encryption Frequency Band: 2.400~2.4835GHz (Industrial Scientific Medical Band) Modulation: CCK@11/5.5Mbps, DQPSK@2Mbps and DBPSK@1Mbps Radio Technology: Direct Sequence Spread Spectrum (DSSS) Antenna: External detachable dipole antenna (with RP-SMA connector) Connectors: 10/100Mbps RJ-45 x 1 Power: 12VDC, 0.4A Transmit Power: 18dBm (Typical) LEDs: Power, LAN Link/Activity, Wireless Activity Dimension: 30(H) x 127(W) x 96(D) mm Temperature: Operating: 32~131°F (0~55°C) Storage: -4~158°F(-20~70°C) Introduction Humidity: 10-90% (Noncondensing) Certification: FCC, CE 1.4 Physical Description Front Panel On the Access Point’s front panel there are LED lights that inform you of the Access Point’s current status. Below is an explanation of each LED. LED Color Power Green Wireless Activity LAN Link/Activity Status On Flash Off Description Power is supplied. Starting up. No Power. Green Flash Off Antenna is transmitting or receiving data. Antenna is not transmitting or receiving data. Green On Flash Off A valid link is established. It is transmitting or receiving data. No link is established. Back Panel Access Point’s connection ports are located on the back panel. Below is the description of each connection port. Introduction y Antenna Connector This round connection is standard Reverse SMA connector where any antennas with Reverse SMA connector can connect to the Access Point. y DC Adapter Port Insert the power jack of the power adapter into this port. y LAN Port The Access Point’s LAN port is where you connect to your LAN’s network devices. y Reset The Reset button allows you to do one of two things. 1) If problems occur with your Access Point, press the reset button with a pencil tip (for less than 4 seconds) and the Access Point will re-boot itself, keeping your original configurations. 2) If problems persist or you experience extreme problems or you forgot your password, press the reset button until the Power LED goes off and the Access Point will reset itself to the factory default settings (warning: your original configurations will be replaced with the factory default settings). Wireless LAN Access Point Connection Chapter 2 Wireless LAN Access Point Connection 1. Locate an optimum location for the Wireless LAN Access Point. The best location for your Access Point is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Connect the Wireless LAN Access Point to your router, hub or switch. Connect one end of standard UTP cable to the Access Point’s LAN Port and connect the other end of the cable to a switch, a router or a hub. The Access Point will then be connected to your existed wired LAN Network. 3. Connect the DC Power Adapter to the Wireless LAN Access Point’s Power Socket. Only use the power adapter supplied with the Access Point. Using a different adapter may damage the product. The Hardware Installation is complete. Wireless LAN Access Point Configuration Chapter 3 Wireless LAN Access Point Configuration 3.1 Getting Started This Access Point provides a web-based configuration tool allowing configuration from wired or wireless stations. Follow the instructions below to start the configuration. From Wired Station 1. Make sure your wired station is in the same subnet with the Access Point. The default IP Address and Sub Mask of the Access Point is: Default IP Address: 192.168.2.1 Default Subnet: 255.255.255.0 Configure your PC to be in the same subnet with the Access Point. 1a) Windows 95/98/Me 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Double-click Network icon. The Network window will appear. 3. Check your list of Network Components. If TCP/IP is not installed, click the Add button to install it now. If TCP/IP is installed, go to step 6. 4. In the Network Component Type dialog box, select Protocol and click Add button. 5. In the Select Network Protocol dialog box, select Microsoft and TCP/IP and then click the OK button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation. 6. After installing TCP/IP, go back to the Network dialog box. Select TCP/IP from the list of Network Components and then click the Properties button. 7. Check each of the tabs and verify the following settings: • Bindings: Check Client for Microsoft Networks and File and printer sharing for Microsoft Networks. • Gateway: All fields are blank. • DNS Configuration: Select Disable DNS. • WINS Configuration: Select Disable WINS Resolution. Wireless LAN Access Point Configuration • IP Address: Select Specify an IP Address. Specify the IP Address and Subnet Mask as following example. IP Address: 192.168.2.3 (any IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.168.2.1) Subnet Mask: 255.255.255.0 8. Reboot the PC. Your PC will now have the IP Address you specified. 1b) Windows XP 1: Click the Start button and select Settings, then click Network Connections. The Network Connections window will appear. 2: Double-click Local Area Connection icon. The Local Area Connection window will appear. 3: Check your list of Network Components. You should see Internet Protocol [TCP/IP] on your list. Select it and click the Properties button. 4: In the Internet Protocol (TCP/IP) Properties window, select Use the following IP address and specify the IP Address and Subnet mask as following. IP Address: 192.168.2.3 (any IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.168.2.1) Subnet Mask: 255.255.255.0 Default gateway: Let all fields are blank. Preferred DNS server: Let all fields are blank. Alternate DNS server: Let all fields are blank. Wireless LAN Access Point Configuration 5: Click OK to confirm the setting. Your PC will now have the IP Address you specified. 1c) Windows 2000 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Double-click Network and Dial-up Connections icon. In the Network and Dial-up Connection window, double-click Local Area Connection icon. The Local Area Connection window will appear. 3. In the Local Area Connection window, click the Properties button. 4. Check your list of Network Components. You should see Internet Protocol [TCP/IP] on your list. Select it and click the Properties button. 5. In the Internet Protocol (TCP/IP) Properties window, select Use the following IP address and specify the IP Address and Subnet mask as following. IP Address: 192.168.2.3 (any IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.168.2.1) Subnet Mask: 255.255.255.0 6. Click OK to confirm the setting. Your PC will now have the IP Address you specified. Wireless LAN Access Point Configuration 1d) Windows NT 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Double-click Network icon. The Network window will appear. Select the Protocol tab from the Network window. 3. Check if the TCP/IP Protocol is on your list of Network Protocols. If TCP/IP is not installed, click the Add button to install it now. If TCP/IP is installed, go to step 5. 4. In the Select Network Protocol window, select the TCP/IP Protocol and click the Ok button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation. 5. After you install TCP/IP, go back to the Network window. Select TCP/IP from the list of Network Protocols and then click the Properties button. 6. Check each of the tabs and verify the following settings: • IP Address: Select Specify an IP address. Specify the IP Address and Subnet Mask as following example. IP Address: 192.168.2.3 (any IP address within 192.168.2.2~192.168.2.254 is available, do not setup 192.168.2.1) Subnet Mask: 255.255.255.0 • DNS: Let all fields are blank. • WINS: Let all fields are blank. • Routing: Let all fields are blank. 7. Click OK to confirm the setting. Your PC will now have the IP Address you specified. 2. Enter 192.168.2.1 from Web Browser to get into the Access Point’s configuration tool. Wireless LAN Access Point Configuration 3. A screen will be popped up and request you to enter user name and password. The default user name and password is as follows. User Name: admin Password: 1234 Enter the default user name and password, then press OK button directly. 4. You can start configuring the Access Point. From Wireless Station 1. Make sure your wireless station is in the same subnet with the Access Point. Please refer to the step 1 above for configuring the IP Address and Sub Mask of the wireless station. 2. Connect to the Access Point. The Access Point’s default ESSID is “default” and the WEP Encryption function is disabled. Make sure your wireless station is using the same ESSID as the Access Point and associate your wireless station to the Access Point. 3. Enter 192.168.2.1 from Web Browser to get into the Access Point’s configuration tool. 4. A screen will be popped up and request you to enter user name and password. The default user name and password is as follows. User Name: admin Password: 1234 Enter the default user name and password, then press OK button directly. 10 Wireless LAN Access Point Configuration 3.2 Configuring the Access Point Every time when you have finished modifying a setting page and click “Apply” button, this page will pop-up. The settings have been successfully saved but will not take effect immediately. You have to restart the access point to make the new settings take effect. You can click “CONTINUE” button to change other settings. You also can click “APPLY” to restart the system and make the settings take effect. 11 Wireless LAN Access Point Configuration 3.2.1 Status and Information On this screen, you can see the general information of the Access Point including Alias Name, Firmware Version, ESSID, Channel Number, Status, IP Address, MAC Address, etc. 12 Wireless LAN Access Point Configuration 3.2.2 Wireless Setting This Access Point supports AP, Station, Bridge, WDS and Universal Repeater modes. “AP Mode” provides pure access point function. The simplest way to build up a wireless LAN is to use “AP Mode”. “Station Mode” is used to let a network device with only wired Ethernet function to have wireless LAN communication capability. It provides both Ad Hoc and Infrastructure modes for the “Station Mode”. With “Station-Ad Hoc mode”, it can let your network device join a wireless LAN with peer-to-peer communication. With “Station-Infrastructure mode”, it can let your network device join a wireless LAN through an access point. “AP Bridge Mode” provides the function to bridge more than 2 wired Ethernet networks together by wireless LAN. You can use two access points with “AP Bridge-Point to Point mode” to bridge two wired Ethernet networks together. If you want to bridge more than two wired Ethernet networks together, you have to use enough access points with “AP Bridge-Point to Multi-Point mode”. An access point with “AP Bridge-Point to Point mode” or “AP Bridge-Point to Multi-Point mode” can only be used to bridge wired Ethernet networks together. It can’t accept connection from other wireless station at the same time. If you want an access point to bridge wired Ethernet network and provide connection service for other wireless station at the same time, you have to set the access point to “AP Bridge-WDS mode”. Simply speaking, “AP Bridge-WDS mode” function is the combination of “AP mode” and “AP Bridge-Point to MultiPoint mode”. “Universal Repeater Mode” provides the function to act as AP client and AP at the same time. It can use AP client function to connect to a Root AP and use AP function to service all wireless stations within its coverage. All the stations within the coverage of this access point can be bridged to the Root AP. “Universal Repeater Mode” is very convenient to extend the coverage of your wireless network. 13 Wireless LAN Access Point Configuration AP mode setting page: 14 Wireless LAN Access Point Configuration Station-Ad Hoc mode setting page: 15 Wireless LAN Access Point Configuration Station-Infrastructure mode setting page: 16 Wireless LAN Access Point Configuration AP Bridge-Point to Point mode setting page: 17 Wireless LAN Access Point Configuration AP Bridge-Point to Multi-Point mode setting page: 18 Wireless LAN Access Point Configuration AP Bridge-WDS mode setting page: 19 Wireless LAN Access Point Configuration Universal Repeater mode setting page: Parameter Description ESSID The ESSID (up to 31 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. Please make sure that the ESSID of all stations in the same WLAN network are the same. The default ESSID is “default”. You should assign ESSID in “AP mode”, “Station-Ad Hoc mode”, “Station-Infrastructure mode”, “AP Bridge-WDS mode” and “Universal Repeater mode”. Band It allows you to set the AP to 802.11b or 802.11g mode. You also can select B+G mode to allow the AP to select 802.11b and 802.11g connection automatically. Channel Number Select the appropriate channel from the list provided to correspond with your network settings. Channels differ from country to country. Channel 1-11 (North America) Channel 1-14 (Japan) 20 Wireless LAN Access Point Configuration Channel 1-13 (Europe) There are 14 channels available. You should assign Channel Number in “AP mode”, “Station-Ad Hoc mode”, “AP Bridge-Point to Point mode”, “AP Bridge-Point to Multi-Point mode” and “AP Bridge-WDS mode”, “Universal Repeater mode”. MAC Address If you want to bridge more than one wired Ethernet networks together with wireless LAN, you have to set this access point to “AP Bridge-Point to Point mode”, “AP Bridge-Point to Multi-Point mode” or “AP BridgeWDS mode”. You have to enter the MAC addresses of other access points that join the bridging work. WLAN BSSID A BSSID is the MAC address of an access point (AP) in an infrastructure mode BSS. If WLAN BSSID is left at the factory default (000000000000), the station (client) will connect to any Access Point (AP) with the specified ESSID. If there is more than one AP with the same ESSID, a station (client) will connect to the AP with the strongest signal. If you want to force a station to connect to a specific AP, then set the WLAN BSSID to the MAC address of the desired AP. WLAN MAC In “Station-Ad Hoc mode”, “Station-Infrastructure mode” and “Universal Repeater mode”, this device needs a WLAN MAC address to act as a station to connect to another peer or Access Point (AP). If WLAN MAC = 000000000000 (factory default), then the device uses the factory assigned MAC address. If you set the WLAN MAC to any other number, the device will use the MAC address you have specified. You also can click “Clone MAC” button to let this device copy the MAC address of the PC you are using to configure this device. If the device is in one of the 3 modes above, and if the wired interface is connected to an Ethernet interface on a router, then it is important to set the WLAN MAC to be identical to the MAC address of the router interface. Auto MAC Clone You can click on this option to let this device copy the MAC address of the PC you are using to configure this device automatically. When clicking on this option, the “Clone MAC” button will be grayed. Root AP SSID In “Universal Repeater mode”, this device can act as a station to connect to a Root AP. You should assign the SSID of the Root AP here. Set Security In “AP Bridge-Point to Point mode”, ““AP Bridge-Point to Multi-Point mode” and “AP Bridge-WDS mode”, you can click “Set Security” to add encryption for the communication between the bridged access points. 21 Wireless LAN Access Point Configuration This can protect your wireless network. Associated Clients Click “Show Active Clients” button, then an “Active Wireless Client Table” will pop up. You can see the status of all active wireless stations that are connecting to the access point. Block Relay You can enable this option to block direct communication between the stations which connect to the same access point. Wireless Site Survey When you use this access point as a wireless station for wired network device to have wireless capability, you have to associate it with a working access point. Click “Select Site Survey” button, then a “Wireless Site Survey Table” will pop up. It will list all available access points near by. You can select one access point in the table and it will join wireless LAN through this access point. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. Set Security “Set Security” let you setup the wireless security for the data transmission between the bridged access points in “AP Bridge-Point to Point mode”, “AP Bridge-Point to Multi-Point mode” or “AP Bridge-WDS mode”. It provides “WEP 64bits”, “WEP 128bits”, “WPA (TKIP)”, “WPA2 (AES)” encryption methods. 22 Wireless LAN Access Point Configuration Parameter Description Encryption You can select “No encryption”,“WEP 64bits”, “WEP 128bits”, “WPA (TKIP)” or “WPA2 (AES)” encryption methods. Key Format This is only used when you select “WEP 64bits” or “WEP 128bits” encryption method. You may select to select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the WEP Key. For example: ASCII Characters: guest Hexadecimal Digits: 12345abcde WEP Key This is only used when you select “WEP 64bits” or “WEP 128bits” encryption method. The WEP key is used to encrypt data transmitted between the bridged access points. Fill the text box by following the rules below. 64-bit WEP: input 10-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or 5-digit ASCII character as the encryption keys. 23 Wireless LAN Access Point Configuration 128-bit WEP: input 26-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or 10-digit ASCII characters as the encryption keys. Pre-shared Key Format You may select to select Passphrase (alphanumeric format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Preshared Key. For example: Passphrase: iamguest Hexadecimal Digits: 12345abcde Pre-shared Key The Pre-shared key is used to authenticate and encrypt data transmitted between the bridged access points. Fill the text box by following the rules below. Hex WEP: input 64-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. Active Wireless Client Table “Active Wireless Client Table” records the status of all active wireless stations that are connecting to the access point. You can lookup the MAC Address, Number of Transmitted Packets, Number of Received Packets and Encryption Status of each active wireless client in this table. 24 Wireless LAN Access Point Configuration Parameter Description MAC Address MAC address of this active wireless station. Tx Packet The number of transmitted packets that are sent out from this active wireless station. Rx Packet The number of received packets that are received by this active wireless station. TX Rate The transmission rate in Mbps. Power Saving Shows if the wireless client is in Power Saving mode. Expired Time The time in second before dissociation. If the wireless keeps idle long than the expired time, this access point will dissociate it. The wireless client station has to associate again when it become active. Refresh Refresh the “Active Wireless Client Table”. 25 Wireless LAN Access Point Configuration Close Refresh the “Active Wireless Client Table”. Wireless Site Survey When this access point is in “Station-Ad Hoc mode”, “Station-Infrastructure mode” or “Universal Repeater mode”, it should associate with an access point or station and connect to your wireless LAN through the associated access point or station. “Wireless Site Survey” searches for all available access points near by. You can select one access point listed in this table. Note: The range of Signal is between 0 and 100. The higher the value, the stronger the signal. 26 Wireless LAN Access Point Configuration 3.2.3 Advanced Setting You can set advanced parameters of this access point. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Tx Operation Rate, Tx Basic Rate, Preamble Type, Broadcast ESSID. You should not change these parameters unless you know what effect the changes will have on this access point. Parameter Description Authentication Type There are two authentication types: “Open System” and “Shared Key”. When you select “Open System”, wireless stations can associate with this access point without WEP encryption. When you select “Shared Key”, you should also setup WEP key in the “Encryption” page and wireless stations should use WEP encryption in the authentication phase to associate with this access point. If you select “Auto”, the wireless client can associate with this access point by using any one of these two 27 Wireless LAN Access Point Configuration authentication types. Fragment Threshold “Fragment Threshold” specifies the maximum size of packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance. RTS Threshold When the packet size is smaller than the RTS threshold, the access point will not use the RTS/CTS mechanism to send this packet. Beacon Interval The interval of time that this access point broadcast a beacon. Beacon is used to synchronize the wireless network. Data Rate The “Data Rate” is the rate this access point uses to transmit data packets. The access point will use the highest possible selected transmission rate to transmit the data packets. Preamble Type Preamble type defines the length of CRC block in the frames during the wireless communication. “Short Preamble” is suitable for high traffic wireless network. “Long Preamble” can provide more reliable communication. Broadcast ESSID If you enable “Broadcast ESSID”, every wireless station located within the coverage of this access point can discover this access point easily. If you are building a public wireless network, enabling this feature is recommended. Disabling “Broadcast ESSID” can provide better security. IAPP If you enable “IAPP”, the access point will automatically broadcast information of associated wireless stations to its neighbors. This will help wireless station roaming smoothly between access points. If you have more than one access points in your wireless LAN and wireless stations have roaming requirements, enabling this feature is recommended. Disabling “IAPP” can provide better security. 802.11g Protection This is also called CTS Protection. It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to the extra data transmissions. 28 Wireless LAN Access Point Configuration Tx Power If you want to lower the transmit power of the access point for saving the power of the system, you can select the lower percentages from the list. The lower power will cause the lower signal strength and the coverage range. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. 29 Wireless LAN Access Point Configuration 3.2.4 Security This Access Point provides complete wireless LAN security functions, include WEP, IEEE 802.11x, IEEE 802.11x with WEP, WPA with pre-shared key and WPA with RADIUS. With these security functions, you can prevent your wireless LAN from illegal access. Please make sure your wireless stations use the same security function. Note: This access point can act as station and AP at the same time in “Universal Repeater mode”. The security settings apply the same configuration to AP function and station function. WEP only When you select 64-bit or128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as default key. Then the access point can receive any packets encrypted by one of the four keys. You can use WEP encryption in “AP mode”, 30 Wireless LAN Access Point Configuration “Station-Ad Hoc mode”, “Station-Infrastructure mode”, “AP Bridge-WDS mode” and “Universal Repeater mode”. Parameter Description Key Length You can select the 64 or 128-bit key to encrypt transmitted data. Larger WEP key length will provide higher level of security, but the throughput will be lower. Key Format You may select to select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the WEP Key. For example: ASCII Characters: guest Hexadecimal Digits: 12345abcde Default Tx Key Select one of the four keys to encrypt your data. Only the key you select it in the “Default key” will take effect. 31 Wireless LAN Access Point Configuration Key 1 - Key 4 The WEP keys are used to encrypt data transmitted in the wireless network. Fill the text box by following the rules below. 64-bit WEP: input 10-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or 10-digit ASCII characters as the encryption keys. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. 802.1x only IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode only authenticates user by IEEE 802.1x, but it does not encrypt the data during communication. You can use 802.1x without encryption in “AP mode”, “AP Bridge-WDS mode” and “Universal Repeater mode”. 32 Wireless LAN Access Point Configuration Parameter Description RADIUS Server IP address The IP address of external RADIUS server. RADIUS Server Port The service port of the external RADIUS server. RADIUS Server Password The password used by external RADIUS server. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. 802.1x WEP static key IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN. The authentication is processed by a RADIUS server. This mode also uses WEP to encrypt the data during communication. You can use 802.1x with WEP encryption in “AP mode”, “AP Bridge-WDS mode” and “Universal Repeater mode”. 33 Wireless LAN Access Point Configuration For the WEP settings, please refer to section “WEP only”. For the 802.1x settings, please refer to section “802.1x only”. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. WPA pre-shared key Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a preshared key to authenticate wireless stations and encrypt data during communication. It uses TKIP or CCMP(AES) to change the encryption key frequently. So the encryption key is not easy to be broken by hackers. This can improve security very much. You can use WPA pre-shared key encryption in “AP mode”, “Station-Ad Hoc mode”, “Station-Infrastructure mode”, “AP Bridge-WDS mode” and “Universal Repeater mode”. Parameter Description 34 Wireless LAN Access Point Configuration WPA(TKIP) TKIP can change the encryption key frequently to enhance the wireless LAN security. WPA2(AES) This use CCMP protocol to change encryption key frequently. AES can provide high level encryption to enhance the wireless LAN security. WPA2 Mixed This will use TKIP or AES based on the other communication peer automatically. Pre-shared Key Format You may select to select Passphrase (alphanumeric format) or Hexadecimal Digits (in the “A-F”, “a-f” and “0-9” range) to be the Preshared Key. For example: Passphrase: iamguest Hexadecimal Digits: 12345abcde Pre-shared Key The Pre-shared key is used to authenticate and encrypt data transmitted in the wireless network. Fill the text box by following the rules below. Hex: input 64-digit Hex values (in the “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. WPA RADIUS Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP(AES) to change the encryption key frequently. This can improve security very much. You can use WPA RADIUS encryption in “AP mode”, “AP Bridge-WDS mode” and “Universal Repeater mode”. 35 Wireless LAN Access Point Configuration Parameter Description WPA(TKIP) TKIP can change the encryption key frequently to enhance the wireless LAN security. WPA2(AES) This use CCMP protocol to change encryption key frequently. AES can provide high level encryption to enhance the wireless LAN security. WPA2 Mixed This will use TKIP or AES based on the other communication peer automatically. RADIUS Server IP address The IP address of external RADIUS server. RADIUS Server Port The service port of the external RADIUS server. RADIUS Server Password The password used by external RADIUS server. 36 Wireless LAN Access Point Configuration Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. 37 Wireless LAN Access Point Configuration 3.2.5 MAC Address Filtering This Access Point provides MAC Address Filtering, which prevents the unauthorized MAC Addresses from accessing your wireless network. Parameter Description Enable Wireless Access Enable or disable the MAC Address Filtering function. Control MAC Address Filtering Table This table records the MAC addresses of wireless stations you want to allow to access your network. The “Comment” field is the description of the wireless station associated with the “MAC Address” and is helpful for you to recognize the wireless station. Add MAC address into the In the bottom “New” area, fill in the “MAC Address” and “Comment” of the table wireless station to be added and then click “Add”. Then this wireless 38 Wireless LAN Access Point Configuration station will be added into the “MAC Address Filtering Table” above. If you find any typo before adding it and want to retype again. Just click “Clear” and both “MAC Address” and “Comment” fields will be cleared. Remove MAC address from If you want to remove some MAC address from the “MAC Address the table Filtering Table”, select the MAC addresses you want to remove in the table and then click “Delete Selected”. If you want remove all MAC addresses from the table, just click “Delete All” button. Reset Click “Reset” will clear your current selections. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. 39 Wireless LAN Access Point Configuration 3.2.6 System Utility From here, you can define the Access Point’s IP Address and Login Password and enable the Access Point to be a DHCP Server. Parameter Description Current Password Enter the current password (up to 15-digit alphanumeric string) of the Access Point. The default password for the Access Point is 1234. Note that the password is case-sensitive. New Password Enter the password (up to 15-digit alphanumeric string) you want to login to the Access Point. Note that the password is case-sensitive. Re-Enter Password Reconfirm the password (up to 15-digit alphanumeric string) you want to login to the Access Point. Note that the password is case-sensitive. 40 Wireless LAN Access Point Configuration IP Address Designate the Access Point’s IP Address. This IP Address should be unique in your network. The default IP Address is 192.168.2.1. Subnet Mask Specify a Subnet Mask for your LAN segment. The Subnet Mask of the Access Point is fixed and the value is 255.255.255.0. Gateway Address The IP address of the default gateway of the subnet that this access point resides in. It allows this access point be accessed by PC from deferent subnet to do configuration. DHCP Server Enable or disable the DHCP Server. Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. DHCP Server Setting DHCP Server will automatically give your LAN client an IP address. If the DHCP is not enabled then you’ll have to manually set your LAN client’s IP address. 41 Wireless LAN Access Point Configuration Parameter Description Default Gateway IP Specify the gateway IP in your network. This IP address should be different from the Management IP. Domain Name Server IP This is the ISP’s DNS server IP address that they gave you; or you can specify your own preferred DNS server IP address. Start IP/End IP You can designate a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients. By default the IP range is from: Start IP 192.168.2.100 to End IP 192.168.2.200. Domain Name You can specify the Domain Name for your Access Point. Lease Time The DHCP Server when enabled will temporarily give your LAN client an IP address. In the Lease Time setting you can specify the time period that the DHCP Server lends an IP address to your LAN clients. The DHCP Server will change your LAN client’s IP address when this time threshold period is reached. 42 Wireless LAN Access Point Configuration Click Apply button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the Access Point. 43 Wireless LAN Access Point Configuration 3.2.7 Configuration Tool The Configuration Tools screen allows you to save (Backup) the Access Point’s current configuration setting. Saving the configuration settings provides an added protection and convenience should problems occur with the Access Point and you have to reset to factory default. When you save the configuration setting (Backup) you can re-load the saved configuration into the Access Point through the Restore selection. If extreme problems occur you can use the Restore to Factory Default selection, this will set all configurations to its original default settings (e.g. when you first purchased the Access Point). Parameter Description Configuration Tools Use the "Backup" tool to save the Access Point’s current configuration to a file named "config.bin" on your PC. You can then use the "Restore" tool to upload and restore the saved configuration to the Access Point. Alternatively, you can use the "Restore to Factory Default" tool to force 44 Wireless LAN Access Point Configuration the Access Point to perform a power reset and restore the original factory settings. 45 Wireless LAN Access Point Configuration 3.2.8 Firmware Upgrade This page allows you to upgrade the Access Point’s firmware. Parameter Description Firmware Upgrade This tool allows you to upgrade the Access Point’s system firmware. To upgrade the firmware of your Access Point, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC. Please reset the Access Point when the upgrade process is complete. Once you’ve selected the new firmware file, click Apply button at the bottom of the screen to start the upgrade process. (You may have to wait a few minutes for the upgrade to complete). Once the upgrade is complete you can start using the Access Point. 46 Wireless LAN Access Point Configuration 3.2.9 Reset You can reset the Access Point’s system should any problem exist. The reset function essentially Re-boots your Access Point’s system. Parameter Description Reset In the event that the system stops responding correctly or in some way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on the Apply button. You will be asked to confirm your decision. Once the reset process is complete you may start using the Access Point again. 47 Troubleshooting Chapter 4 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the Access Point. 1. How to manually find your PC’s IP and MAC Address? 1) In Windows, open the Command Prompt program 2) Type Ipconfig /all and Enter Your PC’s IP address is the one entitled IP address Your PC’s MAC Address is the one entitled Physical Address 2. What is Ad-hoc? An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter, connected as an independent wireless LAN. 3. What is Infrastructure? An integrated wireless and wired LAN is called an Infrastructure configuration. 4. What is BSS ID? A group of wireless stations and an Access Point compose a Basic Service Set (BSS). Computers in a BSS must be configured with the same BSSID. 5. What is ESSID? An Infrastructure configuration could also support roaming capability for mobile workers. More than one BSS can be configured as an Extended Service Set (ESS). Users within an ESS could roam freely between BSSs while maintaining a continuous connection to the wireless network stations and the Wireless LAN Access Points. 6. Can data be intercepted while transmitting through the air? WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent scrambling security feature. On the software side, the WLAN series offers the encryption function (WEP, WPA, WPA2) to enhance security and access control. 48 Troubleshooting 7. What is WEP? WEP stands for Wired Equivalent Privacy, a data privacy mechanism based on a 64(40)-bit shared key algorithm. 8. What is WPA? WPA is an acronym for Wi-Fi Protected Access. It is a security protocol for 802.11 wireless networks. WPA can provide data protection with the use of encryption and the use of access controls and user authentication. 9. What is WPA2? In addition to WPA, WPA2 provides a stronger encryption mechanism through Advanced Encryption Standard (AES). 10. What is a MAC Address? The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network. 49 Troubleshooting Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 50
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2007:05:30 16:29:32+08:00 Create Date : 2007:05:30 14:24:15+08:00 Metadata Date : 2007:05:30 16:29:32+08:00 Format : application/pdf Title : Creator : . Document ID : uuid:633878ff-6856-4a2d-a88a-c5b5c34855eb Instance ID : uuid:4cca5316-863a-4a6a-afb3-5830f7e8c0b6 Page Count : 52EXIF Metadata provided by EXIF.tools