Election Systems and Software ESSM100A Optical Scan Voting Machine with GSM User Manual

Election Systems & Software Optical Scan Voting Machine with GSM

Contents

GR48 User Guide

Product Photo/Illustration GR47/GR48Integrator’s Manual
The GR47 described in this manual conforms to the Radio and Telecommunications Terminal Equipment (R&TTE) directive 99/5/EC with requirements covering EMC directive 89/336/EEC and Low Voltage directive 73/23/EEC. The product fulfils the requirements according to 3GPP TS 51.010-1, EN 301 489-7 and EN60950.SAR statement: This product is intended to be used with the antenna or other radiating element at least 20 cm away from any part of the human body.The information contained in this document is the proprietary information of Sony Ericsson Mobile Communications International.The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of SonyEricsson Mobile Communications International, is strictly prohibited. Further, no portion of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, without the prior written consent of Sony Ericsson Mobile Communications International, the copyright holder.First edition (May 2003)Sony Ericsson Mobile Communications International publishes this manual without making any warranty as to the content contained herein. Further Sony Ericsson Mobile Communications International reserves the right to make modifications, additions and deletions to this manual due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this manual.All rights reserved.©Sony Ericsson Mobile Communications International, 2003Publication number: LZT 123 7589 R1APrinted in UK
LZT 123 7589 R1AContentsOverview ...................................................................................................................51. Introduction .............................................................................................................. 6Target Users ................................................................................................................ 6Prerequisites................................................................................................................ 6Manual Structure......................................................................................................... 62. GR47/GR48 Radio Devices ...................................................................................... 7About the GR47/GR48 Family................................................................................... 7Radio Devices in a Communication System ................................................................. 7Features....................................................................................................................... 9Service and Support ................................................................................................... 12Precautions................................................................................................................ 133. Abbreviations.......................................................................................................... 14Integrating the Radio Device ................................................................................164. Mechanical Description.......................................................................................... 17Interface Description ................................................................................................. 17Physical Dimensions.................................................................................................. 185. System Connector Interface ................................................................................... 19Overview................................................................................................................... 19General Electrical and Logical Characteristics ............................................................ 22Grounds .................................................................................................................... 23VCC - Regulated Power Supply Input ....................................................................... 23Battery Charging Input (CHG_IN) ........................................................................... 24Turning the Radio Device ON/OFF and the External Power Signal........................... 25Analogue Audio ........................................................................................................ 29PCM Digital Audio................................................................................................... 33Serial Data Interfaces ................................................................................................. 36SIM Card Related Signals .......................................................................................... 40Service/Programming ................................................................................................ 41Buzzer ....................................................................................................................... 42LED .......................................................................................................................... 42General Purpose Digital I/O Ports............................................................................. 43Extended I/O capabilities .......................................................................................... 44General Purpose Analogue I/O Ports ......................................................................... 45External I 2C Serial Control Bus................................................................................. 48TX_ON - Burst Transmission ................................................................................... 49
LZT 123 7589 R1AReal Time Clock........................................................................................................ 496. Antenna Connector................................................................................................. 517. Keyboard Interface ................................................................................................. 52IO#/KEYROW#....................................................................................................... 52KEYCOL# ................................................................................................................ 528. Hints for Integrating the Radio Device................................................................. 54Safety Advice and Precautions ................................................................................... 54Installation of the Radio Device................................................................................. 56Antenna .................................................................................................................... 589. Embedded Applications ......................................................................................... 60Features..................................................................................................................... 60Implementation......................................................................................................... 6010. TCP/IP Stack........................................................................................................... 62Implementation......................................................................................................... 6211. Technical Data ........................................................................................................ 6312. Declaration of Conformity...................................................................................... 65Developer’s Kit .......................................................................................................6613. Introduction to the Developer’s Kit ...................................................................... 67Contents of the Kit.................................................................................................... 67General Functioning of the Kit.................................................................................. 6814. Using the Developer’s Kit...................................................................................... 71Start up Check List.................................................................................................... 72Developer’s Board Overlay......................................................................................... 73Jumpers..................................................................................................................... 74Switches .................................................................................................................... 78Headers ..................................................................................................................... 79Connectors ................................................................................................................ 80LED Indicators .......................................................................................................... 82System Connector Pin Assignments........................................................................... 83
Product Photo/Illustration Overview
6LZT 123 7589 R1A1. Introduction1.1 Target UsersThe GR47 and GR48 radio devices are designed to be integrated into machine-to-machine or man-to-machine communications applications. They are intended to be used by manufacturers, system integrators, applications developers and developers of wireless communications equipment.1.2 PrerequisitesIt is assumed that the person integrating the radio device into an application has a basic understanding of the following:• GSM networking;• Wireless communication and antennas (aerials);• AT commands;• ITU-T standard V.24/V.28;• Micro controllers and programming;• Electronic hardware design.1.3 Manual StructureThe manual is composed of three parts:Part 1- OverviewThis section provides a broad overview of the GR47/GR48 family and includes a list of abbreviations used in the manual.Part 2 - Integrating the Radio DeviceThis section describes each of the signals available on the GR47/GR48 radio devices, along with mechanical information. The section also provides you with design guidelines and explains what is needed to commercialise an application from a regulatory point of view.Part 3 - Developer’s KitThis section lists the contents of the Developer’s Kit and provides the information to setup and use the equipment.
2. GR47/GR48 RADIO DEVICES7LZT 123 7589 R1A2. GR47/GR48 Radio Devices2.1 About the GR47/GR48 FamilyTwo radio devices make up the family; GR47 and GR48, for use in the E-GSM900/GSM1800 and GSM850/GSM1900 bands respectively.1RWH This manual refers to the GR47 and GR48 as radio devices. If there is a difference in the functionality of the radio devices the GR47 and GR48 information will be listed separately.The products belong to a new generation of Sony Ericsson radio devices, and are intended to be used in machine-to-machine applications and man-to-machine applications. They are used when there is a need to send and receive data (by SMS, CSD, HSCSD, or GPRS), and make voice calls over the GSM network.The radio devices can either have applications embedded onto them or they can be used as the engine in an application created by the customer. The radio device can send and receive data when a script is executed, the script can be run internally from the radio device itself or from a micro-controller. A typical application, involves a micro-controller and a radio device, in which the micro-controller sends AT commands to the radio device via an RS232 communications link. 2.2 Radio Devices in a Communication SystemFigures 2.1 and 2.2 illustrate the main blocks of a wireless communication system using the radio device. Figure 2.1 shows the communication system when the script is embedded on the radio device and figure 2.2 shows the communication system when a micro-controller is used. They also show the communication principles of the system and the interface between the radio device and the application. The definitions in the figures, as used elsewhere in this manual, are in accordance with the recommendations of GSM 07.07.• The MS (mobile station) represents the radio device and SIM card. The radio device excluding SIM card, is known as the ME (mobile equipment). • The DTE (data terminal equipment) is the controlling application. This can be either an external host or an internal embedded application.• The DCE (data circuit terminating equipment) is the serial communication interface of the MS.
2. GR47/GR48 RADIO DEVICES8LZT 123 7589 R1A.Figure 2.1 Main Blocks in a Wireless System (embedded application)Figure 2.2 Main Blocks in a Wireless System (external micro-controller)In accordance with the recommendations of ITU-T (International Telecommunication Union - Telecommunications Standardisation Sector) V.24, the TE communicates with the MS over a serial interface.SIMMSPOWERSUPPLYGR47 / GR48GSMENGINEDCE DTESTATUS &RESPONSE‘AT’ COMMANDCONTROLEMBEDDEDAPPLICATIONSYSTEM CONNECTORGSM NETWORKSIMMSPOWERSUPPLYGR47 / GR48GSMENGINEDCEDTESYSTEM CONNECTORGSM NETWORKDTEEXTERNALAPPLICATION MS STATUS &RESPONSE‘AT’ COMMANDCONTROL M
2. GR47/GR48 RADIO DEVICES9LZT 123 7589 R1AThe functions of the radio device follow the recommendations provided by ETSI (European Telecommunications Standards Institute) and ITU-T.ETSI specifies a set of AT commands for controlling the GSM element of the radio device; these commands are supplemented by Sony Ericsson specific commands.To find out how to work with AT commands, see the AT Commands Manual.2.3 FeaturesThe radio device performs a set of telecom services (TS) according to GSM standard phase 2+, ETSI and ITU-T. The functions of the radio device are implemented by issuing AT commands over a serial interface.2.3.1 Types of Mobile StationGR47 and GR48 are dual band mobile stations with the characteristics shown in the tables below.GR47 E-GSM 900 GSM 1800Frequency Range (MHz) TX: 880-915RX: 925-960TX: 1710-1785RX: 1805-1880Channel spacing 200 kHz 200 kHzNumber of channels 174 carriers *8 time slots 374 carriers *8 time slotsModulation GMSK GMSKTX phase accuracy < 5º RMS phase error (burst) < 5º RMS phase error (burst)Duplex spacing 45 MHz 95 MHzReceiver sensitivity at antenna connector< –102 dBm < –102 dBmTransmitter output power at antenna connectorClass 4 2 W (33 dBm)Class 11 W (30 dBm)Automatic hand-over between E-GSM 900 and GSM 1800 GR48 GSM 850 GSM 1900Frequency Range (MHz) TX: 824-849RX: 869-894TX: 1850-1910RX: 1930-1990Channel spacing 200 kHz 200 kHzNumber of channels 124 carriers *8 time slots 299 carriers *8 time slotsModulation GMSK GMSKTX Phase Accuracy < 5º RMS phase error (burst) < 5º RMS phase error (burst)
2. GR47/GR48 RADIO DEVICES10LZT 123 7589 R1A2.3.2 Short Message ServiceThe radio device supports the following SMS services:• Sending; MO (mobile-originated) with both PDU (protocol data unit) and text mode supported.• Receiving; MT (mobile-terminated) with both PDU and text mode supported.• CBM (cell broadcast message); a service in which a message is sent to all subscribers located in one or more specific cells in the GSM network (for example, traffic reports).• SMS STATUS REPORT according to GSM 03.40.The maximum length of an SMS message is 160 characters when using 7-bit encoding. For 8-bit data, the maximum length is 140 characters. The radio device supports up to six concatenated messages to extend this function. Concatenation is disabled if CNMI 3,2 is set (See the AT Commands Manual for further details).2.3.3 Voice CallsThe radio device offers the capability of MO (mobile originated) and MT (mobile terminated) voice calls, as well as supporting emergency calls. Multi-party, call waiting and call divert features are available. Some of these features are network-operator specific.For the inter-connection of audio, the radio device offers both single ended and balanced analogue input and output lines. Direct interface to the digital PCM (pulse code modulation) bus used within the radio device is available, thus by-passing the internal analogue circuitry.The radio devices support HR, FR and EFR vocoders.The GR48 also supports the Adaptive Multi Rate (AMR) type of vocoder.Duplex spacing 45 MHz 80 MHzReceiver sensitivity at antenna connector< –102 dBm < –102 dBmTransmitter output power at antenna connectorClass 42W (33 dBm)Class 11 W (30 dBm)Automatic hand-over between GSM 850 and GSM 1900 GR48 GSM 850 GSM 1900
2. GR47/GR48 RADIO DEVICES11LZT 123 7589 R1A2.3.4 DataThe radio device supports the following data protocols:•*356*HQHUDO3DFNHW5DGLR6HUYLFH The radio devices are Class B terminals. The radio devices are GPRS 4+1 enabled, which are capable of receiving at a maximum of four timeslots per frame (down link), and transmitting in one timeslot per frame (up link).•&6'&LUFXLW6ZLWFKHG'DWD The radio devices are capable of establishing a CSD communication at 9.6 kbps.•+6&6'+LJK6SHHG&LUFXLW6ZLWFKHG'DWD The radio devices support HSCSD communication, with one timeslot per frame capacity in the up link and two timeslots per frame capacity in the down link (2+1).2.3.5 SIM CardAn external SIM card with 3 V or 5 V technology, can be connected to the radio device via its 60-pin system connector.2.3.6 Power Consumption1RWH The power consumption during transmission is measured at maximum transmitted power.2.3.7 Other FeaturesThese include:• 07.10 multiplexing.• GPS interoperability.• SIM application tool kit, class 2 release 96 compliant.• Embedded application • On board TCP/IP stack• E-OTD (Supported by GR48)Idle Mode Transmit/OperationGSM 850 and E-GSM 900 Voic e/C SD < 5 mA < 250 mA (< 2 A peak)Data (GPRS 4+1) < 5 mA < 350 mA (< 2 A peak)GSM 1800 and GSM 1900 Voic e/C SD < 5 mA < 250 mA (<1.75 A peak)Data (GPRS 4+1) < 5 mA < 350 mA (<1.75 A peak)
2. GR47/GR48 RADIO DEVICES12LZT 123 7589 R1A2.4 Service and Support2.4.1 Web PagesVisit our web site for the following information:• where to buy radio devices or for recommendations concerning accessories and components;• the telephone number for customer support in your region;• FAQs (frequently asked questions).The web site address is:http://www.SonyEricsson.com/M2M2.4.2 Integrator’s ManualThis manual provides you with all of the information you need to integrate the radio device into your application.2.4.3 AT Commands ManualThe AT Commands Manual provides you with all the AT commands you can use with your radio device. AT commands are in logical groups and contain the command, a description of its functionality and an example of use.2.4.4 M2mpower Application GuideThe M2mpower Application Guide provides you with all the information you need to build an application using the M2mpower support environment. This manual is supplied as part of the M2mpower package.2.4.5 Developer’s KitSony Ericsson provides the developer’s kit to get you started quickly. The kit includes the necessary hardware required to begin the development of an application. It includes the following:• GSM radio device, GR47 or GR48;• This Integrator’s Manual;• Developer’s kit hardware;• Developer’s kit accessories;– Power supply– RS232 cable– Headset– Antenna.
2. GR47/GR48 RADIO DEVICES13LZT 123 7589 R1AAll the user needs to provide, is a computer or micro-controller and the expertise to use AT commands.2.5 PrecautionsThe radio devices are ESD protected up to 4K V contact and 8K V air discharge. It is recommended that you follow electronic device handling precautions when working with any electronic device system to ensure no damage occurs to the host or the radio device. In “Integrating the Radio Device”, page 16 you will find more information about safety and product care. Do not exceed the environmental and electrical limits as specified in “Technical Data”, page 63.
3. ABBREVIATIONS14LZT 123 7589 R1A3. AbbreviationsAbbreviation ExplanationsAMR Adaptive Multi RateATMS Audio to Mobile StationAFMS Audio from Mobile StationCBM Cell Broadcast MessageCBS Cell Broadcast ServiceCSD Circuit Switched DataDCE Data Circuit Terminating EquipmentDK Developer’s KitDTE Data Terminal EquipmentDTMF Dual Tone Multi FrequencyEA Embedded ApplicationEFR Enhanced Full Rate EMC Electro-Magnetic CompatibilityE-OTD Enhanced Observed Time DifferenceETSI European Telecommunication Standards InstituteFR Full Rate GPRS General Packet Radio ServiceGPS Global Positioning SystemGSM Global System for Mobile CommunicationHR Half RateHSCSD High Speed Circuit Switched DataIDE Integrated Development EnvironmentIP Internet ProtocolITU-T International Telecommunication Union - Telecommunications Standardisation SectorM2mpower Sony Ericssons powerful support environmentME Mobile EquipmentMMCX Micro Miniature CoaxMO Mobile OriginatedMS Mobile StationMT Mobile TerminatedPCM Pulse Code Modulation
3. ABBREVIATIONS15LZT 123 7589 R1APDU Protocol Data UnitRF Radio FrequencyRFU Reserved for Future UseRLP Radio Link ProtocolRTC Real Time ClockSDP Service Discovery ProtocolSIM Subscriber Identity ModuleSMS Short Message ServiceTCP Transport Control ProtocolUDP User Datagram ProtocolAbbreviation Explanations
Product Photo/Illustration Integrating the Radio Device
17LZT 123 7589 R1A4. Mechanical Description4.1 Interface DescriptionThe pictures below show the mechanical design of the radio device along with the positions of the different connectors and mounting holes. The radio device is protected with AISI 304 stainless steel covers that meet the environmental and EMC requirements. Figure 4.1 Radio Device viewed from belowFigure 4.2 Radio Device, viewed from abovePlease note the following:• Mounting holes positioned at the corners make it possible to securely bolt the radio device into your application.Mounting hole/ground connectionAntenna connectorSystem connector
4. MECHANICAL DESCRIPTION18LZT 123 7589 R1A• Keypad, display, microphone, speaker and battery are not part of the radio device.• The SIM card is mounted in your application, external to the radio device.• The System Connector is a 60-pin, standard 0.05 in (1.27 mm) pitch type. The pins and their electrical characteristics are described in 5. System Connector Interface, page 19.• Information about the Antenna Connector is found in 6. Antenna Connector, page 51.4.2 Physical DimensionsFigure 4.3 Dimensions of the Radio DeviceMeasurements are given in millimetres. See also Technical Data, page 63.4.789.0046.4050.002.20 (4x)1.802.862.053.804.602.807.15 2.9030.202.3033.003.00
19LZT 123 7589 R1A5. System Connector Interface5.1 OverviewElectrical connections to the radio device (except the antenna), are made through the System Connector Interface. The system connector is a 60-pin, standard 0.05 in (1.27 mm) pitch device.The system connector allows both board-to-board and board-to-cable connections to be made. Use a board-board connector to connect the radio device directly to a PCB, and a board-cable connector to connect the radio device via a cable.Figure 5.1 below shows the numbering of the connector pins.A ground connection is provided at the mounting hole next to the RF connector on the radio device as shown below. Connect this ground point to the DGND pins of the radio device by the shortest, low-impedance path possible. The purpose of this connection is to allow any antenna ESD strikes to bypass the radio device’s internal ground path.Figure 5.1 Radio Device, viewed from underneathThe following table gives the pin assignments for the system connector interface and a short description for each signal.Pin 59 Pin 1Pin 60 Pin 2Groundconnection
5. SYSTEM CONNECTOR INTERFACE20LZT 123 7589 R1A1RWH Under the heading “Dir” in the table, radio device input and output signals are indicated by the letters I and O respectively.Pin Signal Name Dir Signal Type Description1VCC -Supply Power supply2 DGND - - Digital ground3VCC -Supply Power supply4 DGND - - Digital ground5VCC -Supply Power supply6 DGND - - Digital ground7VCC -Supply Power supply8 DGND - - Digital ground9VCC -Supply Power supply10 DGND - - Digital ground11 CHG_IN -Battery charge powerBattery charging12 DGND - - Digital ground13 IO5 ADC4I/0 IDigital 2.75V AnalogueGeneral purpose input/output 5 Analogue to digital converter 414 ON/OFF I Internal pull up, open drainTurns the radio device on and off.15 SIMVCC -Digital 3 V/5 V SIM card power supply. Power output from radio device for SIM Card16 SIMPRESENCE I Internal pull up, open drain SIM PresenceA “1” indicates that the SIM is missing; a “0” that it is inserted17 SIMRST ODigital 3 V/5 V SIM card reset18 SIMDATA I/O Digital 3 V/5 V SIM card data19 SIMCLK ODigital 3 V/5 V SIM card clock20 DAC O Analogue Digital to analogue converter21 IO1 KEYROW2I/O IDigital 2.75V General purpose input/output 1 Keyboard row 222 IO2 ADC5I/O IDigital 2.75V AnalogueGeneral purpose input/output 2 Analogue to digital converter 523 IO3 KEYROW3I/O IDigital 2.75V General purpose input/output 3 Keyboard row 324 IO4 KEYROW4I/O IDigital 2.75V General purpose input/output 4 Keyboard row 425 VRTC ISupply 1.8V Supply for real time clock26 ADC1 I Analogue Analogue to digital converter 127 ADC2 IAnalogue Analogue to digital converter 2
5. SYSTEM CONNECTOR INTERFACE21LZT 123 7589 R1A28 ADC3 I Analogue Analogue to digital converter 329 SDA I/O 2.75V, internal pull up I 2 C data30 SCL O 2.75V, internal pull up I 2 C clock31 BUZZER ODigital 2.75V Buzzer output from radio device32 OUT3 KEYCOL3 DSROO ODigital 2.75V General purpose output 3 Keyboard column 3 Data set ready (UART1)33 LED IO6O I/ODigital 2.75V Flashing LED General purpose I/O 634 VIO O Power Out 2.75 VRadio device power indication. VIO is a 2.75 V at 75 mA output supply that can be used to power external circuitry that interfaces to the radio device35 TX_ON ODigital 2.75V This output indicates when the GSM radio device is going to transmit the burst36 RI KEYCOL2 O2O O ODigital 2.75V Ring Indicator (UART1) Keyboard column 2 General purpose output 237 DTR KEYROW1 IN1I I IDigital 2.75V Data Terminal Ready (UART1) Keyboard row 1 General purpose input 138 DCD KEYCOL1 O1O O ODigital 2.75V Data Carrier Detect (UART1) Keyboard column 1 General purpose output 139 RTS IO9I I/ODigital 2.75V Request To Send (UART1) General purpose I/O 940 CTS KEYCOL4 O4OOODigital 2.75V Clear To Send (UART1)Keyboard column 4General purpose output 441 TD IDigital 2.75V Transmitted Data (UART1).Data from DTE (host) to DCE (radio device). 42 RD O Digital 2.75V Received Data (UART1).Data from DCE (radio device) to DTE (host).43 TD3I/O7II/ODigital 2.75V Transmitted data (UART3) General purpose I/O 744 RD3I/O8OI/ODigital 2.75V Received data (UART3) General purpose I/O 845 TD2 IDigital 2.75V Transmitted data (UART2). Used for flashing the memory. 46 RD2 O Digital 2.75V Received data (UART2).Used for flashing the memory. 47 PCMULD IDigital 2.75V DSP PCM digital audio input48 PCMDLD O Digital 2.75V DSP PCM digital audio outputPin Signal Name Dir Signal Type Description
5. SYSTEM CONNECTOR INTERFACE22LZT 123 7589 R1A5.2 General Electrical and Logical CharacteristicsMany of the signals, as indicated in the table above, are high-speed CMOS logic inputs or outputs powered from a 2.75 V ± 5 % internal voltage regulator, and are defined as Digital 2.75 V. Whenever a signal is defined as Digital 2.75 V, the following electrical characteristics apply.1RWH Unused pins can be left floating.5.2.1 General Protection Requirements• All 2.75 V digital inputs will continuously withstand and suffer no damage in the power-on or power-off condition when subjected to any voltage from - 0.5 V to 3.47 V (3.3 V + 5 %).• All 2.75 V digital outputs will continuously withstand a short circuit to any other voltage within the range 0 V to 3 V.• All analogue outputs will continuously withstand a short circuit to any voltage within the range 0 V to 3 V.49 PCMO ODigital 2.75V Codec PCM digital audio output50 PCMI I Digital 2.75V Codec PCM digital audio input51 PCMSYNC ODigital 2.75V DSP PCM frame sync52 PCMCLK O Digital 2.75V DSP PCM clock output53 MICP IAnalogue Microphone Input positive54 MICN I Analogue Microphone Input negative55 BEARP OAnalogue Speaker output positive 56 BEARN O Analogue Speaker output negative57 AFMS OAnalogue Audio output from radio device58 SERVICE I 2.7V Flash programming voltage for the MS. Enable logger information if not flashing.59 ATMS IAnalogue Audio input to radio device60 AGND - Analogue Analogue groundPin Signal Name Dir Signal Type DescriptionParameter Min. Max. UnitsHigh Level Output Voltage (VOH), Io = –2mA 2.2 2.75 VLow Level Output Voltage (VOL), Io = 2mA 0 0.6 VHigh Level Input Voltage (VIH)1.93 2.75 VLow Level Input voltage (VIL)00.5V
5. SYSTEM CONNECTOR INTERFACE23LZT 123 7589 R1A• The SIM output signals and the SIMVCC supply will continuously withstand a short circuit to any voltage within the range 0 V to 4.1V.5.3 GroundsThere are two ground connections in the radio device, AGND (analogue ground) and DGND (digital ground). Pin assignments are shown in the table above.1RWH AGND and DGND are connected at a single point inside the radio device. They must not be joined together in your application.5.3.1 Analogue Ground - AGNDAGND is the return signal, or analogue audio reference, for ATMS (Audio To Mobile Station) and AFMS (Audio From Mobile Station). It is connected to the DGND inside the radio device only. The application must not connect DGND and AGND. 5.3.2 Digital Ground - DGNDDGND is the reference or return signal for all system interface digital signals and is also the d.c. return for SERVICE and the power supply, VCC. Connect all DGND pins together in your application in order to carry the current drawn by the radio device.5.4 VCC - Regulated Power Supply InputPower is supplied to the radio device VCC pins, from an external source.Pin Signal Description2, 4, 6, 8, 10, 12 DGND Digital ground60 AGND Analogue groundParameter LimitImax ≅12.5 mAParameter Per Pin Total (5 Pins)Imax < 6.0A < 3.0A Iavg < 100mA < 600mAPins Signal Description1, 3, 5, 7, 9 VCC regulated power supply input
5. SYSTEM CONNECTOR INTERFACE24LZT 123 7589 R1AConnect all VCC pins together in your application in order to carry the current drawn by the radio device.The electrical characteristics for VCC are shown in the table below.1RWH The radio device has no internal capacitance to supply the large current peaks during GSM burst transmission. We recommend you follow these general guidelines:• Fit a low ESR electrolytic capacitor close to the radio device: > 1,000 µF; < 100 mΩ ESR.• Make sure power supply to radio device line resistance is < 200 mΩ.5.5 Battery Charging Input (CHG_IN)For battery powered applications, the radio device has a connection to aid and support battery charging. The typical design where this may be applicable is to power the radio device directly from a battery source connected to VCC (pins 1, 3, 5, 7, 9) and to provide a 5V dc power source (600mA max) to the CHG_IN connection (pin 11). The radio device can control an internal switching FET which creates a charging pathway to the battery. While power is provided at CHG_IN, the battery charge can be maintained. If the power should fail or be removed at CHG_IN, the application will be supported by the battery alone. When CHG_IN voltage returns, the battery charging and maintenance will commence once more.&DXWLRQ Battery charging algorithms are unique to different battery types. Sony Ericsson Mobile Communications will not accept any responsibility or liability for damage, product failures, even death or injury occurring as a result of incompatible battery and charging algorithms being applied without their prior knowledge and consent. Parameter Mode LimitVcc supply voltage Nominal 3.6 VTolerance including ripple aa. Measured at system connector pins.3.4 V - 4.0 VOver-voltage limit 5.5 VMaximum ripple < 100 mV @ <200 kHz; < 20 mV @ > 200 kHzMaximum allowable voltage dropBurst transmission 200 mVCurrent drawn, at full TX power< 500 mA (average)< 2 A (peak)
5. SYSTEM CONNECTOR INTERFACE25LZT 123 7589 R1ASafety considerations should be taken into account. For example, monitoring the temperature of the battery. If the temperature of the battery exceeds its specification limits, battery charging must be stopped immediately. If the battery temperature continues to rise the application should be suspended or the battery disconnected.1RWH When charging Lithium batteries, the battery pack must have an internal protection circuit in accordance with the manufacturer’s instructions.5.6 Turning the Radio Device ON/OFF and the External Power SignalTurning the Radio Device OnFigure 5.2 On timings and VIO performanceON/OFF pulledup internallythrough 39kΩtONtVIOtCTStPULSESoftware running…tPRSTVCCON/OFFVIOCTStOSymbol Parameters Conditions Min. Typ Max UnittReference time when VCC is within working limits (1)VCC > 3.2VON/OFF = VCC-- - -tTime after t0 when the ON/OFF pulse can beginVCC > 3.2V 0 - - ms
5. SYSTEM CONNECTOR INTERFACE26LZT 123 7589 R1A(1) The GR47 measures the voltage at VCC during the power-up sequence. It is important that both VCC and ON/OFF reach a minimum of 3.2V before the ON/OFF low pulse is initiated.(2) In SERVICE mode.tTime after start of ON/OFF pulse when VIO is activeVCC > 3.2V - 45.0 - mstApplication ON/OFF pulse widthON/OFF held low until detected by software400 500 -mstInternal Power-on reset signal initiates software100 - 200 mstTime when software controlled CTS signal indicates module READYCTS signal configured for RS232 hardware flow control, not GPIO pin-0.35 3.0(2) s
5. SYSTEM CONNECTOR INTERFACE27LZT 123 7589 R1ATurning the Radio Device OffFigure 5.3 Off timings and VIO performance(2) It is a requirement from most GSM network providers that GSM products properly detach from the network during a power-down sequence. In order to achieve this it is important that the VCC supply is not removed or turned off before VIO has been deactivated by the module.ON/OFFVIOtSPDtOFFtPULSEtSCSDVCC(Performs GSM Network detachand SIM power management)Software controlledshutdown.Symbol Parameters Conditions Min. Typ Max UnittTime for software pulse detection which initiates a software shutdown800 - - mstApplication ON/OFF pulse width1000 - - mstSoftware controlled shutdown deactivates VIO (2)-)2.5)10(3) s)tTime when VCC power supply can be disabledVIO is DISABLED0 - - ms
5. SYSTEM CONNECTOR INTERFACE28LZT 123 7589 R1AHard Shutdown SequenceFigure 5.4 Hard Shutdown Sequence(4) To implement the Hard Shutdown of the GR47, the ON/OFF pulse must be held low until the sequence is complete. Ensure that ON/OFF is not released before VIO has been deactivated by the module.5.6.1 VIO - 2.75V SupplyVIO provides an output voltage derived from an internal 2.75V regulator. Its electrical characteristics are shown below.You can use this output for the following:• to indicate that the radio device is powered;• to power interface circuits, external to the radio device.ON/OFFVIOtHSDtPULSESymbol Parameters Conditions Min. Typ Max UnittTime to complete hardware shutdown2-11stApplication ON/OFF pulse widthON/OFF low until VIO is disabledt10 - sParameter Min. Typ. Max. UnitsOutput Voltage (Iload = 50 mA) 2.70 2.75 2.85 VLoad current 75 mA
5. SYSTEM CONNECTOR INTERFACE29LZT 123 7589 R1A5.7 Analogue AudioATMS is the audio input, and AFMS is the audio output, of the radio device. These signals can be used in car kit mode.There are three factory-set audio profiles:• portable handsfree• handset• car kitPortable handsfree is the factory-set default profile. The modification, configuration, manipulation and storage of audio profiles is achieved with the AT*E2EAMS (Audio Profile Modification) and AT*E2APR (Audio Profile).5.7.1 Audio To Mobile Station - ATMSATMS is the analogue audio input to the radio device. Internally, the signal is sent to the CODEC (COder/DECoder), where it is converted to digital audio in PCM (Pulse Code Modulation) format. The encoded audio is sent to PCMOUT via the internal PCM bus.ATMS provides a DC bias when it is used as the microphone input in Portable Hands-free applications. All other sources must be a.c.-coupled to avoid attenuation of low frequencies, and to prevent incorrect biasing or damage to the ATMS input. Use a capacitor greater than the value shown in the table below.The ATMS input is a passive network followed by the transmit part of the CODEC.Pin Signal Dir Description57 AFMS OAudio from mobile station59 ATMS I Audio to mobile station60 AGND -Ground (return) for analogue audioParameter LimitApplication driving impedance (0.3 - 3.5 kHz) ≤ 300 ΩAC coupling capacitance ≥ 1 µFRadio device input impedance (0.3 - 3.5 kHz) > 50 kΩLow frequency cut-off (- 3 dB) 300 Hz ± 50 HzHigh frequency cut-off (– 3 dB) > 3500 Hz ± 50 HzOutput d.c. bias level car kit mode 0 VAdditional Gain in car kit mode 28.5 dB
5. SYSTEM CONNECTOR INTERFACE30LZT 123 7589 R1AThe following tables show the nominal PGA (programming gain settings). For more information see the relevant AT commands.Maximum input voltage limit: 245 mVrms Maximum input level at MICI, 61.4 mVrms output at PCMOUT = 3 dBm0Output at AFMS for 3 dBm0 at PCMINOutput at BEARN/BEARP for 3 dBm0 at PCMIN5.7.2 Audio From Mobile Station - AFMSAFMS is the analogue audio output from the radio device and may be used to drive a speaker or the ear-piece in a car kit.PCM digital audio signals, entering the radio device through the PCMIN pin, are translated to analogue signals by the CODEC. See 5.8 PCM Digital Audio, page 33 for further information.The table below shows the audio signal levels for AFMS.Input Input (mVrms) TXAGC (dB) AUX AMP gainPCMOUT (dBm0)ATMS 245 013 3Input Differential input (mVrms)TXAGC (dB) AUX AMP gainPCMOUT (dBm0)MICN MICP61.4 025 3Input dBm0 RXPGA Volume control (dB)AFMS (mVrms)PCMIN 3 0 0 436Input dBm0 RXPGA Volume control (dB)BEAR (mVrms)PCMIN 3 0 0 388Parameter LimitSpeaker impedance 64 Ω to 1 kΩ
5. SYSTEM CONNECTOR INTERFACE31LZT 123 7589 R1A5.7.3 Microphone SignalsMICP and MICN are balanced differential microphone input pins. These inputs are compatible with an electret microphone. The microphone contains an FET buffer with an open drain output, which is supplied with at least +2 V relative to ground by the radio device as shown below.Figure 5.5 Microphone connections to the radio deviceOutput Capacitance 2.2 µF ±10 %Levels (THD < 5 %) Drive capability into 5 kΩ (0.3 - 3.5 kHz)> 2.4 Vp-p Drive capability into 1.5 kΩ (0.3 - 3.5 kHz)> 2.2 Vp-p Drive capability into 150 Ω (at 1 kHz)> 1.3 Vp-p Parameter LimitPin Speaker signals Dir Function53 MICP IMicrophone positive input54 MICN I Microphone negative inputMICP1k1kGR47MICN68nF68nF2 - 2.5V@ 1mACODECAGND
5. SYSTEM CONNECTOR INTERFACE32LZT 123 7589 R1A5.7.4 Speaker SignalsBEARP and BEARN are the speaker output pins. These are differential-mode outputs. The electrical characteristics are given in the table below.(5) See PCMIN signal in 5.8 PCM Digital Audio, page 33.The following table shows the ear piece impedances that can be connected to BEARP and BEARN.Pin Speaker signals Dir Function55 BEARP OSpeaker positive output56 BEARN O Speaker negative outputParameter LimitOutput level (differential) ≥ 4.0 VOutput level (dynamic load = 32 Ω)≥ 2.8 VGain PCMIN(5) to BEARP/BEARN (differential) – 9 dB ± 1Distortion at 1 kHz and maximum output level ≤ 5 %Offset, BEARP to BEARN ± 30 mVEar-piece mute-switch attenuation ≥ 40 dBEar piece model Impedance ToleranceDynamic ear piece [32 Ω + 800 µH] // 100 pF ± 20 %Dynamic ear piece [150 Ω + 800 µH] // 100 pF ± 20 %Piezo ear piece 1 kΩ + 60 nF ± 20 %
5. SYSTEM CONNECTOR INTERFACE33LZT 123 7589 R1A5.8 PCM Digital AudioFigure 5.6 shows the PCM (Pulse Code Modulation) digital audio connection for external devices. These connections can be used to process PCM digital audio signals, bypassing the radio device’s internal analogue audio CODEC.Figure 5.6 Pin connections to digital audio1RWH When no external audio processing is performed, the following pins must be connected together:• PCMDLD to PCMIN• PCMULD to PCMOUTElectrical characteristicsDigital 2.75 V CMOS input/output electrical characteristics apply.Pin Signal Dir Function52 PCMCLK OPCM clock51 PCMSYNC O PCM frame sync47 PCMULD IPCM audio input to DSP48 PCMDLD O PCM audio output from DSP50 PCMIN IPCM audio input to Codec49 PCMOUT O PCM audio output to CodecDSP CODECPCMSYNC & PCMCLKAnalogueaudiosignalsPCMINPCMOUTPCMDLDPCMULDLink for internaldigital-audio processingGR47System connector
5. SYSTEM CONNECTOR INTERFACE34LZT 123 7589 R1A5.8.1 PCM Data FormatAll of the radio device’s PCM signals, including signals between its CODEC and DSP conform to the PCM data I/O format of the industry standard DSP from Texas Instruments.PCMCLK (bit clock) and PCMSYNC (frame synchronisation) are both generated by the DSP within the radio device.The DSP within the radio device is the master therefore all external PCM clocks and data from external devices must be synchronized to it13-Bit PCM ModeThe radio device implements 13-bit PCM with the 13-bit data embedded in a 16-bit word within a 24-bit frame (see Figure 5.8). Each PCM word contains 16-bits: D0 to D15. D13 to D1 is the two’s complement value of the 13-bit PCM, with D13 as the sign bit. D14 and D15 are always set to be equivalent with D13. D0, the LSB, is not used as shown in Figure 5.7 below.Figure 5.7 16-bit data word format16-Bit PCM ModeThe frame format is equal to the one shown in Figure 5.7, but with D15, D14 and D0 filled with significant bits. D15 to D0 is the two’s complement value of the 16-bit PCM with bit 15 as the sign bit.Bit ContentsD15 to D14 Equal to D13D13 to D1 Two’s complement of the 13-bit PCMD0 LSB, not usedMSB D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 LSB16 bit data word13 bit PCM=D13 D0Bit ContentsD15 - D0 Two’s complement
5. SYSTEM CONNECTOR INTERFACE35LZT 123 7589 R1APCM Timing DiagramsThe PCM timing is shown in Figure 5.8 below and it is seen that the CPU has 45 µs to serve an interrupt and setup data channels. Data is sent on the falling edge of the sync pulse. The data bits in PCMULD and PCMDLD are aligned so that the MSB in each word occurs on the same clock edge as shown in Figure 5.9.Figure 5.8 16-bit word within 24-bit framePCM signal timing is shown in Figure 5.9. The signals characteristics are described in the tables following Figure 5.9.Figure 5.9 PCM Timing DiagramClkSyncData45 µs125 µsPCMCLKPCMSYNPCMINPCMOUT XMSB D14 D13MSB D14 D13tPSStPSHtDSLtDSHtPDLPName Description Typ. UnittPSS PCMSYN (setup) to PCMCLK (fall) 2.5 µstPSH PCMSYN pulse length 5 µstDSL PCMI (setup) to PCMCLK (fall) 2.5 µstDSH PCMI (hold) from PCMCLK (fall) 2.5 µstPDLP PCMO valid from PCMCLK (rise) 2.5 µsName Description Typ. UnitFPCMCLK PCM clock frequency 200 kHzTPCMCLK PCM clock period with 50/50 mark space ratio 5 µsFPCMSYN PCM sync frequency 8kHz
5. SYSTEM CONNECTOR INTERFACE36LZT 123 7589 R1A5.9 Serial Data InterfacesThe serial channels, consisting of three UARTs, are asynchronous communication links to the application or accessory units. • UART1 has RS-232 functionality and is used for all on- and off -line communication.• UART2 behaves as a general-purpose serial data link. For example, it can be used for GPS, downloading software and receiving logging information.• UART3 behaves as a general-purpose serial data link. It can be used by an embedded application.Typical Rise/Fall times Rise Time Fall Time UnitPCMCLK 19 18 nsPCMSYN 19 15 nsPCMOUT 900 900 nsPCMDLD 20 19 nsPin Signal Dir Description RS232 CCITT Nº41 TD ISerial data to radio device (UART1) 10342 RD O Serial data from radio device (UART1) 10439 RTSIO9II/ORequest To Send (UART1)General purpose input/output 910540 CTSKeyCOL4O4OOOClear To Send (UART1)Key column 4General purpose output 410637 DTRKeyROW1IN1IIData Terminal Ready (UART1)Keyboard row 1General purpose input 1108.232 DSRKeyCOL3O3OOOData Set Ready (UART)Key column 3General purpose output 310738 DCDKeyCOL 1O1OOOData Carrier Detect (UART1)Key column 1General purpose output 110936 RIKeyCOL 2O2OOORing Indicator (UART1)Key Column 2General output 212545 TD2 ITransmitted Data (UART2)46 RD2 O Received Data (UART2)43 TD3 ITransmitted Data (UART3)44 RD3 O Received Data (UART3)
5. SYSTEM CONNECTOR INTERFACE37LZT 123 7589 R1ADigital 2.75 V CMOS input/output electrical characteristics apply.The standard character format consists of 1 start bit, 8 bit data, no parity and 1 stop bit. In all, there are 10 bits per character.5.9.1 UART1 (RS232) - RD, TD, RTS, CTS, DTR, DSR, DCD and RIUART1 signals conform to a 9-pin RS232 (V.24) serial port.1RWH UART1 signal levels do not match standard RS232 (V.28) levels. The relationship between the levels is shown in the table below. Conversion between the radio device CMOS levels and RS232 levels can be achieved using a standard interface IC, such as the Maxim Integrated Products MAX3237.5.9.2 Serial Data Signals - RD, TDThe default baud rate is 9.6 kbits/s, however higher bit rates of up to 460 kbits/s are supported, set by an AT command. UART1 starts at a rate of 9.6 kbits/s in standard AT command mode. The radio device also supports GSM 07.10 multiplexing protocol and starts when the appropriate command is sent.Serial Data From Radio Device (RD)RD is an output signal that the radio device uses to send data via UART1 to the application.Serial Data To Radio Device (TD)TD is an input signal, used by the application to send data via UART1 to the radio device.RS232 level RD, TD RTS, CTS, DTR, DSR, DCD, RI CMOS level< – 3 V 1OFF > 1.93 V> + 3 V 0 ON < 0.80 VParameter LimitApplication load resistance < 100 kΩApplication load capacitance < 100 pFParameter LimitApplication driving impedance < 100 ΩInput capacitance 1nFInput resistance 100 kΩ to 2.75 V
5. SYSTEM CONNECTOR INTERFACE38LZT 123 7589 R1A5.9.3 Control Signals - RTS, CTS, DTR, DSR, DCD, RIUART1 control signals are active low and need a standard interface IC, such as the MAX3237, to generate standard RS232 levels.UART1 converted signals, together with DGND, RD and TD form a 9-pin RS232 data port.RTS and CTS are capable of transmitting at 1/10th of the data transmission speed for data rates up to 460 kbit/s (byte-oriented flow control mechanism).1RWH When hardware flow control is not used in communications between the application and the radio device, RTS and CTS must be connected to each other at the radio device.Switching times for RTS and CTSThe table below shows the switching times.Request to Send (RTS)Used to condition the DCE for data transmission. The default level is high by internal pull up.The application must pull RTS low to enable data transmission from the radio device. Similarly, the radio device asserts CTS low, indicating it is ready to receive data transmission from the host.Clear To Send (CTS)CTS is asserted by the DCE to indicate that the host (DTE) may transmit data. When CTS is high, the host (DTE) is not permitted to transmit data.The table below shows the load characteristics for this signal. Parameter LimitTime from Low to High level < 2 µsTime from High to Low level < 2 µsParameter LimitApplication driving impedance < 100 ΩInput capacitance < 2 nFInput resistance (pull-up) 100 kΩ to DGNDParameter LimitApplication load capacitance < 500 pFApplication load resistance ≥ 1 MΩ
5. SYSTEM CONNECTOR INTERFACE39LZT 123 7589 R1AData Terminal Ready (DTR)DTR indicates that the DTE is ready to receive data. It also acts as a hardware ‘hang-up’, terminating calls when switched high. The signal is active low. You can define the exact behaviour of DTR with an AT command.Data Set Ready (DSR)DSR indicates that the DCE is ready to receive data. The signal is active low.Data Carrier Detect (DCD)DCD indicates that the DCE is receiving a valid carrier (data signal) when low.Ring Indicator (RI)RI indicates that a ringing signal is being received by the DCE when low. You can define the exact behaviour of RI with an AT command.5.9.4 UART2 - TD2, RD2UART 2 consists of a full duplex serial communication port with transmission and reception lines.This communication port works in a mode called Operation and Maintenance.Operation and Maintenance mode works in combination with the SERVICE signal. Two events are possible if the SERVICE signal is active when the radio device is turned on. These are:• the radio device is reprogrammed if UART2 is connected to a computer running Sony Ericsson update software;• the radio device enters logging mode and sends data to UART2 if no reprogramming information is received.Timing and electrical signals characteristics are the same as for UART1, TD and RD, except for maximum baud rate which could increase to 921 kbps.Transmitted Data 2 (TD2)TD2 is used by the application to send data to the radio device via UART2. It has the same electrical characteristics as TD.Received Data 2 (RD2)RD2 is used to send data to the application via UART2. It has the same electrical characteristics as RD.
5. SYSTEM CONNECTOR INTERFACE40LZT 123 7589 R1A5.9.5 UART3 - TD3, RD3UART3 is a full duplex serial communication port with transmission and reception lines. It has the same timing and electrical signal characteristics as UART1, TD and RD.Transmitted Data 3 (TD3)TD3 is used by your application to send data to the radio device via UART3.Received Data 3 (RD3)RD3 is used to send data to your application via UART3.5.10 SIM Card Related SignalsThese connections allow you to communicate with the SIM card holder in your application.1RWH The distance between the SIM card holder and the radio device can be up to 25cm.This SIM interface allows the use of 3 V and 5 V SIM cards. By default it works on 3 V levels but will automatically switch to 5 V, if a 5 V SIM card is fitted.SIM voltage levels, as shown in the following table, are dependent on the type of SIM card detected by the radio device. Pin Signal Dir Description15 SIMVCC -SIM card power supply16 SIMPRESENCE I SIM card presence17 SIMRST OSIM card reset19 SIMCLK O SIM card clock18 SIMDATA I/O SIM card dataSignal Parameter Mode Min. Typ. Max. UnitSIMVCC SIM supply voltage 3 V 2.7 3.0 3.3 V5 V 4.5 5.0 5.5 VSIMDAT High Level Input voltage (V )3 V 2.1 3.0 V5 V 3.5 5.0 VSIMDAT Low Level Input voltage (V )3 V 00.9 V5 V 0 1.5 V
5. SYSTEM CONNECTOR INTERFACE41LZT 123 7589 R1A5.10.1 SIM Detection - SIMPRESENCESIMPRESENCE is used to determine whether a SIM card has been inserted into or removed from the SIM card holder. You should normally wire it to the “card inserted switch” of the SIM card holder, but different implementations are possible.When left open, an internal pull-up resistor maintains the signal high and means “SIM card missing” to the radio device. When pulled low the radio device assumes a SIM card is inserted.SIMPRESENCE is a Digital 2.75V CMOS input with the following electrical characteristics.1RWH To meet regulatory approvals SIMPRESENCE must be implemented.5.11 Service/ProgrammingWhen the SERVICE input signal is active the radio device will:• be reprogrammed if data is received through UART2 from a computer running Sony Ericsson reprogramming software;• or it will output logging data on UART2.SIMDAT High Level Output voltage (V )3 V 2.7 3.0 V5 V 4.7 5.0 VSIMDAT Low Level Output voltage (V )3 V 00.2 V5 V 0 0.2 VSIMCLKSIMRSTHigh Level Output voltage (V )3 V 2.4 3.0 V5 V 4.4 5.0 VSIMCLKSIMRSTLow Level Output voltage (V )3 V 00.35 V5 V 0 0.3 VSignal Parameter Mode Min. Typ. Max. UnitParameter Min. Typ. Max. UnitsPull-up resistance (at 2.75 V) 100 kΩLow Level Input voltage (SIM inserted) 0.80 VHigh Level Input voltage (SIM missing) > 1.93 2.75 VPin Signal Dir Description58 SERVICE IFlash programming voltage
5. SYSTEM CONNECTOR INTERFACE42LZT 123 7589 R1AThe electrical characteristics are given below. The signal reference is DGND.5.12 BuzzerConnecting the BUZZER signal to an inverting transistor-buffer followed by a piezoelectric transducer enables the radio device to play pre-programmed melodies or sounds.5.13 LEDThe LED states shown below, are hard coded.Mode SERVICE Voltage (V) Drive CapacityMin. Typ. Max.Normal Operation 0.8 -Service/enable programming1.9 2.75V 3.6 > 1 mAAbsolute maximum voltage13.5Pin Signal Dir Description31 BUZZER OBuzzer output from radio devicePin Signal Dir Description33 LED OLED Output from radio deviceLED indication Operational statusNo indication No power or in the OFF stateGreen, steady Power on, not connected to a networkGreen, blinking Power on, connected to a network
5. SYSTEM CONNECTOR INTERFACE43LZT 123 7589 R1AThe following circuit can be used to connect an LED.Figure 5.10 Electrical connections for the LED5.14 General Purpose Digital I/O PortsSignals which have an entry in the Default Signal column in the above table are multiplexed. LED10k33010kBC817GR47/48DGNDVCCPin I/O port signalDefault signalDescription21 IO1 IO1 Programmable Input/Output 1KEYRow222 IO2 IO2 Programmable Input/Output 2ADC523 IO3 IO3 Programmable Input/Output 3KEYRow324 IO4 IO4 Programmable Input/Output 4KEYRow413 IO5 IO5 Programmable Input/Output 5ADC433 IO6 LED Programmable Input/Output 6/LED43 IO7 TD3 Programmable Input/Output 7/TD344 IO8 RD3 Programmable Input/Output 8/RD339 IO9 RTS Programmable Input/Output 9/RTS37 IN1 DTR Programmable Input 1Data Terminal Ready32 OUT3 DSR Programmable Output 3/DSR36 OUT2 RI Programmable Output 2/RIRing Indicator38 OUT1 DCD Programmable Output 1/DCDData Carrier Detect40 OUT4 CTS Programmable Input/Output 4/CTS
5. SYSTEM CONNECTOR INTERFACE44LZT 123 7589 R1AThe operational modes of multiplexed signals are controlled by AT commands and also by intrinsic functions available to an embeddedThe following table gives you the input impedance. These values only apply when the ports are configured as input signals. 1RWHV I/O6 (LED) doesn’t have an internal pull up. If this pin is configured as an input, it should not be left floating. I/O7 (TD3) has a pull down instead of a pull up.5.15 Extended I/O capabilitiesTo increase flexibility and variety of radio device peripherals, the RS232 hardware flow control shares its physical interface with the keypad scanning interface and the extended general purpose I/O capability. This sharing means that it is not feasible to operate all these features concurrently, however, with care, dynamic switching from one feature to another is possible.Using Embedded ApplicationsWhen a particular I/O feature is required, the user sets the state of the relevant I/O blocks by disabling one set before enabling others. The radio device checks the state of the I/O when the user requests a new function. The new function is rejected if the current function is not released first.1RWH Only the states of I/O1 - I/O5 are retained for the next power up. For example, inputs remain as inputs and outputs remain as outputs. The voltage of a defined output pin will still drop to 0 Volts in the radio device power down state.5.15.1 LED/IO6 CapabilitiesThe LED function pin can be used as a general purpose digital I/O when the flashing LED function is not required. However, this pin does not have an on-board pull-up resistor. It is required that an external pull-up or pull-down resistor be provided by the host circuitry when either not used or when used as a digital input.Parameter Min. Typ. Max. UnitsInput impedance (pull-up) 50 100 120 kΩ
5. SYSTEM CONNECTOR INTERFACE45LZT 123 7589 R1A5.15.2 I#/O#If pins labelled I# and O# are not being used for an alternative function they may be used for general purpose inputs or outputs respectively. The inputs have an on-board 100k pull-up resistor and the outputs are driven rail-to-rail at 2.75V levels.5.15.3 UART3/IO#The UART3 pins have been given alternative functions as general purpose I/O, both pins may be used for either input or output. However, the TX pin has a 100kΩ pull-down resistor to ground and the RX pin has a 100kΩ pull-up resistor to 2.75V. This must be taken into consideration when designing the host circuit.5.15.4 IO#/ADC#To increase analog input capabilities, the radio device optimises the I/O by multiplexing or sharing different features on single pins. There are two digital I/O pins which now have an additional ADC input. When configured as digital I/O, the software will not read the voltages at the two new ADC inputs. When configured as ADC inputs the software will configure the digital I/O pins as input or high impedance tri-state. In this state any applied voltage between 0V and 2.75V can be read as an 8 bit value.Because the additional ADC inputs (ADC4 and ADC5) are common with digital I/O, the input circuit of the ADC is not the same as for the original circuits ADC1-3. It is important to understand the input structure of the pin so that the correct analog voltage is read by the application.5.16 General Purpose Analogue I/O PortsThe radio device is able to convert digital to analogue signals and vice versa.Pin Signal Dir Description20 DAC ODigital to analogue conversion output26 ADC1 I Analogue to digital conversion input 127 ADC2 IAnalogue to digital conversion input 228 ADC3 I Analogue to digital conversion input 313 ADC4 (I/O5) I (I/O) Analogue to digital conversion input 422 ADC5 (I/O2) I (I/O) Analogue to digital conversion input 5
5. SYSTEM CONNECTOR INTERFACE46LZT 123 7589 R1A5.16.1 Digital to Analogue Converter - DACThe DAC is an 8-bit converter. Conversion takes place when an AT command is sent to the radio device. The radio device sends the resulting analogue value to the DAC pin.Tolerance on this internal voltage is ± 5 %DAC output electrical characteristics are given in the following table.(6)Tolerance on this internal voltage is ± 5 %(7)Referred to the ideal conversion characteristic.(8)See Figure 5.11, page 46Figure 5.11 DAC loadsParameter Limit UnitsResolution 8BitsOutput voltage for code = 0 (2.75(6) x 0.05) ± 0.05 VOutput voltage for code = 255 (2.75(6) x 0.95) ± 0.05 VNominal step size (2.75(6) x 0.9)/256 mVAbsolute error(7) ≤ ± 0.5 mVOutput wide-band noise and clock feed-through 0 - 1.1 MHz ≤ 0.5 mVrmsPower-supply rejection ratio 50 Hz - 10 kHz ≥ 40 dBConversion rate ± 0.5 LSB ≤ 2 (Load A)(8) ms≤ 50 (Load B)(8) msOutput buffer impedance when disabled ≥ 50 kΩOutput current source or sink ≥ 1mACurrent consumption (active) ≤ 1.0 mA1kDGNDDAC1nF10nFLoad B100kDGNDDAC100 - 200pF Load A
5. SYSTEM CONNECTOR INTERFACE47LZT 123 7589 R1A5.16.2 Analogue to Digital Converters 1, 2 and 3 - ADCxThe ADC is an 8-bit converter. An analogue value applied to any of the ADC pins is converted and stored in a register inside the radio device. When the appropriate AT command is received by the radio device, the digital value stored in the register is read.ADC electrical characteristics are shown in the table below.(9) Tolerance on this internal voltage is ±5%5.16.3 Analogue to Digital Converters 4 and 5 - IOx/ADCxTo increase analog input capabilities, the GR47 optimises the I/O by multiplexing or sharing different features on single pins. There are two ADC inputs which share system connector pins with digital I/O signals. When configured as digital I/O, the software will not read the voltages at the two new ADC inputs. When configured as ADC inputs the software will configure the digital I/O pins as input or high impedance tri-state. In this state any applied voltage between 0V and 2.75V can be read as an 8 bit value.Because the ADC inputs, ADC4 and ADC5, are common with digital I/O, the input circuit of these Adds is not the same as for the circuits ADC1, ADC2 and ADC3. It is important to understand the input structure of the pin so that the correct analog voltage is read by the application (at position ’A’ in Figure 5.12 below). The input structure is provided in Figure 5.12. It consists of a 100kΩ pull-up to 2.75V followed by a series 10kΩ and 1nF capacitor to ground which make a low pass filter with a 3dB roll-off at about 16kHz. The input impedance of the analog IC is 1MΩ minimum. At position ’A’ in Figure 5.12 below, the input characteristics are the same as for the table above.Parameter Min. Max. UnitsResolution 88BitsInput voltage for 0000 0000 word 0 0.01 x 2.75(9) VInput voltage for 1111 1111 word 0.99 x 2.75(9) 2.75(9) VDifferential Non-Linearity (DNL) ± 0.75 LSBOverall Non-Linearity (INL) ± 0.60 LSBAbsolute accuracy ± 1.5 LSBInput impedance 1 MΩAverage supply current (continuous conversion)1mAExternal source impedance 50 kΩ
5. SYSTEM CONNECTOR INTERFACE48LZT 123 7589 R1A1RWH If the voltage of the signal to be measured may be altered by the internal circuitry of this shared signal, then the application should use ADC1, ADC2 or ADC3 instead.Figure 5.12 Input circuit for combined digital I/O and ADC pins5.17 External I 2C Serial Control BusThe I 2 C bus is controlled by embedded application script commands. The external I 2 C bus consists of two signals, SDA and SCL. This bus is isolated from the radio device’s internal I 2 C bus to ensure proper operation of the radio device, in the event of the external I 2 C bus being damaged.The electrical characteristics are shown below.2.75VADC100kΩ10kΩA2.75VAnalog IC10#/ADC#1MΩ1nFPin Signal Dir Description29 SDA I/O I 2 C serial data30 SCL O I 2 C serial clockParameter Min. Typ. Max. UnitsTransmitoperationFrequency I 2 C CLK 81.25 400 kHzHigh or low I 2 C CLK 1.2 µsDelay time after falling edge of I 2 C CLK308 308-1230nsHold time after falling edge of I 2 C CLK0ns
5. SYSTEM CONNECTOR INTERFACE49LZT 123 7589 R1A5.18 TX_ON - Burst TransmissionBurst transmission is the time when a GSM transceiver unit is transmitting RF signals. TX_ON indicates the radio device is going into transmission mode. 5.19 Real Time ClockThe Real Time Clock (RTC) provides the main microprocessor with a time-of-day calendar and alarm, and a one-hundred-year calendar. Its accuracy is shown in the table belowThe Real Time Clock operates in two modes when connected to a separate power supply:• RTC normal mode: the radio device is in ON or OFF mode and it is supplied with power (VCC is applied).• RTC back-up mode: VCC is disconnected and the RTC is maintained by a separate backup power supply connected to the VRTC input (see Figure 5.13 below).Backup power is provided by a capacitor, golden-capacitor or battery in your application and must be connected to the VRTC pin. During RTC normal operation, the back up source will be charged.ReceiveoperationFrequency I 2 C CLK 400 kHzHigh or low I 2 C CLK 1.2 µsDelay time after falling edge of I 2 C CLK100 nsHold time after falling edge of I 2 C CLK0nsParameter Min. Typ. Max. UnitsPin Signal Dir Description35 TX_ON OGSM radio device to transmitPin Signal Dir Description25 VRTC -Voltage for the Real Time ClockParameter Min. Typ. Max. UnitsRTC accuracy 25°C 8 (21) 20 (52) ppm (s/month)RTC accuracy extreme temperatures89 (231) 101 (262) ppm (s/month)
5. SYSTEM CONNECTOR INTERFACE50LZT 123 7589 R1AIn back-up mode, the back-up source must provide enough power for RTC operation. Refer to the table for the amount of current required.The following table shows voltage characteristics for both modes.If the voltage drops below 1.0 V in back-up mode, the RTC will stop working. The following diagram shows the RTC connections.Figure 5.13 RTC connectionsParameter Min. Typ. Max. UnitsSupply Voltage RTC (normal mode - charging the capacitor)1.6 1.8 2.0 VSupply Voltage RTC (back-up mode - Capacitor provides the current)1.0 1.8 2.0 VCurrent drawn 5.0 10.0 µABackupsupplyVRTC+GR47DGND
6. ANTENNA CONNECTOR51LZT 123 7589 R1A6. Antenna ConnectorThe radio device’s antenna connector allows transmission of the radio frequency (RF) signals from the radio device to an external customer-supplied antenna. The connector is a micro-miniature coaxial MMCX surface mounted component. A number of suitable MMCX type, mating plugs are available from the following manufacturers;• Amphenol;• Suhner;• IMS Connector Systems.The nominal impedance of the antenna interface is 50Ω.
7. KEYBOARD INTERFACE52LZT 123 7589 R1A7. Keyboard InterfaceTo increase I/O capabilities, the radio device optimises the I/O by multiplexing or sharing different features on single pins. The I/O has been extended to allow simple interfacing of a matrix keypad.7.1 IO#/KEYROW#When configured for keypad operation the software will configure the dig-ital I/O pins as input or high impedance tri-state. In this state, the keypad matrix row can be read from the KEYROW# inputs. These pins have a 100kΩ pull-up to 2.75V and the rows are considered activated when the voltage is pulled low by the external keypad switches.7.2 KEYCOL#The keypad matrix column drivers share functionality with the RS232 hardware flow control signals. In addition to the keypad column outputs it is possible to use a direct ground connection as an additional column driver, which is interpreted as column zero.Simply connect one keypad column directly to ground. When a key in this column is depressed KEYROW# is activated.Thus it is possible to create a variety of keypad matrix sizes from single column to five columns wide.Finally, a standard keypad matrix directly connects the rows to the columns whenever a key is depressed. In order to avoid short circuits if multiple keys are pressed simultaneously, the column drivers must be open-collector. This must be achieved with external transistors as the logic drive from the radio device is rail-to-rail. Suitable transistors for this interface are of the type with built in bias resistors between base and emitter.
7. KEYBOARD INTERFACE53LZT 123 7589 R1AThe method of connection is shown below.Figure 7.1 Keyboard matrix connections1RWH This matrix pattern may be repeated up to 5 columns and 4 rows (one column will use a ground connection as a virtual column driver).Examples of suitable transistors are:6KEYCOL#KEYROW#4321RN1107RN1107RN11075GR47Brand Part NumberToshiba RN1107 (as shown)On SEMI DTC114YET1Philips PDTC114YEROHM DTC114YETL
8. HINTS FOR INTEGRATING THE RADIO DEVICE54LZT 123 7589 R1A8. Hints for Integrating the Radio DeviceThis chapter gives you advice and helpful hints on how to integrate the radio device into your application from a hardware perspective.Please read and consider the information under the following headings before starting your integration work:• Safety advice and precautions.• Installation of the radio device.• Antenna.8.1 Safety Advice and Precautions8.1.1 General• Always ensure that use of the radio device is permitted. The radio device may present a hazard if used in proximity to personal medical electronic devices. As a rule, the radio device must not be used in hospitals, airports or planes.• You are responsible for observing your country’s safety standards, and where applicable the relevant wiring rules.• Never use the radio device at a gas station, refuelling point, blasting area or in any other environment where explosives may be present.• Operating the radio device close to other electronic devices, such as antennas, television sets, and radios may cause electromagnetic interference.• Never try to dismantle the radio device yourself. There are no components inside the radio device that can be serviced by the user. If you attempt to dismantle the radio device, you may invalidate the warranty.• To protect the power supply cables and meet the fire safety requirements, it is recommended that the electrical circuits are supplied with a power regulator. The power regulator should be placed as close to the terminals of the power supply as possible.• Do not connect any incompatible component or product to the radio device. 1RWH Sony Ericsson does not warrant against defects, non-conformities or deviations caused thereby.• The connection/disconnection method for the development board is by means of the DC power jack. For this reason, the mains supply should be situated close to the development board and be easily accessible.
8. HINTS FOR INTEGRATING THE RADIO DEVICE55LZT 123 7589 R1A8.1.2 SIM Card• Before handling the SIM card in your application, ensure that you are not charged with static electricity. Use proper precautions to avoid electrostatic discharges. The radio device must be switched off before the SIM card is installed in your application.• When the SIM card hatch is opened, the SIM card connectors lie exposed under the SIM card holder. CAUTION: Do not touch these connectors! If you do, you may release an electrical discharge that could damage the radio device or the SIM card.• When designing your application, the SIM card’s accessibility should be taken into account. We always recommend that you have the SIM card protected by a PIN code. This will ensure that the SIM card cannot be used by an unauthorized person.8.1.3 Antenna• If the antenna is to be mounted outside, consider the risk of lightning. Follow the instructions provided by the antenna manufacturer.• Never connect more than one radio device to a single antenna. The radio device can be damaged by radio frequency energy from the transmitter of another radio device.• Like any mobile station, the antenna of the radio device emits radio frequency energy. To avoid EMI (electromagnetic interference), you must determine whether the application itself, or equipment in the application’s proximity, needs further protection against radio emission and the disturbances it might cause. Protection is secured either by shielding the surrounding electronics or by moving the antenna away from the electronics and the external signals cable.• The radio device and antenna may be damaged if either come into contact with ground potentials other than the one in your application. Beware, ground potential are not always what they appear to be.• In the final application, the antenna must be positioned more than 20 cm away from human bodies. When this rule cannot be applied, the application designer is responsible for providing the SAR measurement test report and declaration.• Even if SAR measurements are not required, it is considered good practice to insert a warning in any manual produced, indicating it is a radio product and that care should be taken.
8. HINTS FOR INTEGRATING THE RADIO DEVICE56LZT 123 7589 R1A8.2 Installation of the Radio Device8.2.1 Where to Install the Radio DeviceThere are several conditions which need to be taken into consideration when designing your application as they might affect the radio device and its function. They are:Environmental ConditionsThe radio device must be installed so that the environmental conditions stated in the Technical Data chapter, such as temperature, humidity and vibration are satisfied. Additionally, the electrical specifications in the Technical Data section must not be exceeded.Signal StrengthThe radio device has to be placed in a way that ensures sufficient signal strength. To improve signal strength, the antenna can be moved to another position. Signal strength may depend on how close the radio device is to a radio base station. You must ensure that the location at which you intend to use the radio device, is within the network coverage area. Degradation in signal strength can be the result of a disturbance from another source, for example an electronic device in the immediate vicinity. More information about possible communication disturbances can be found in section 8.3.5, page 59.When an application is completed, you can verify signal strength by issuing the AT command AT+CSQ. See the AT Commands Manual for further details.7LS Before installing the radio device, use an ordinary mobile telephone to check a possible location for it. In determining the location for the radio device and antenna, you should consider signal strength as well as cable lengthConnection of Components to Radio DeviceThe integrator is responsible for the final integrated system. Incorrectly designed or installed, external components may cause radiation limits to be exceeded. For instance, improperly made connections or improperly installed antennas can disturb the network and lead to malfunctions in the radio device or equipment.Network and Subscription• Before your application is used, you must ensure that your chosen network provides the necessary telecommunication services. Contact your service provider to obtain the necessary information.
8. HINTS FOR INTEGRATING THE RADIO DEVICE57LZT 123 7589 R1A• If you intend to use SMS in the application, ensure this is included in your (voice) subscription.• Consider the choice of the supplementary services described in section 2.3.2 Short Message Service, page 10.8.2.2 How to Install the Radio DevicePower Supply• Use a high-quality power supply cable with low resistance. This ensures that the voltages at the connector pins are within the allowed range, even during the maximum peak current. An electrolytic capacitor should be placed close to the power supply pins of the radio device to supply the peak currents during burst transmission. See 5.4 VCC - Regulated Power Supply Input, page 23.• See section 5.2.1 General Protection Requirements, page 22.GroundsA ground connection is provided at the mounting hole next to the RF connector on the radio device (see Figure 5.1, page 19). Connect this ground point to the DGND pins of the radio device by the shortest, low-impedance path possible. The purpose of this connection is to allow any ESD picked up by the antenna to bypass the radio device’s internal ground path.1RWH It is recommended that you use a cable with a maximum resistance of 5 mΩ for the ground connection.1RWH AGND and DGND are connected at a single point inside the radio device. They must not be joined together in your application.AudioUse a coupling capacitor in ATMS line if the application does not use the radio device’s bias voltage. See also Figure 5.5 Microphone connections to the radio device, page 31.Software UpgradeTo upgrade the software, the system connector must be accessible in your application. The pins SERVICE, TD2, RD2 and the power signals are used for this purpose. Please contact customer support for more details.
8. HINTS FOR INTEGRATING THE RADIO DEVICE58LZT 123 7589 R1A8.3 Antenna8.3.1 GeneralThe antenna is the component in your system that maintains the radio link between the network and the radio device. Since the antenna transmits and receives electromagnetic energy, its efficient function will depend on:• the type of antenna (for example, circular or directional);• the placement of the antenna;• communication disturbances in the vicinity in which the antenna operates.In the sections below, issues concerning antenna type, antenna placement, antenna cable, and possible communication disturbances are addressed.In any event, you should contact your local antenna manufacturer for additional information concerning antenna type, cables, connectors, antenna placement, and the surrounding area. You should also determine whether the antenna needs to be grounded or not. Your local antenna manufacturer might be able to design a special antenna suitable for your the application.8.3.2 Antenna TypeMake sure that you choose the right type of antenna for the radio device. Consider the following requirements:• the antenna must be designed for the dual frequency bands in use: E-GSM900/GSM1800 for the GR47 and GSM 850/GSM1900 for the GR48;• the impedance of the antenna and antenna cable must be 50 Ω;• the antenna output-power handling must be a minimum of 2 W;• the VSWR value should be less than 3:1 to avoid damage to the radio device.8.3.3 Antenna PlacementThe antenna should be placed away from electronic devices or other antennas. The recommended minimum distance between adjacent antennas, operating in a similar radio frequency band, is at least 50 cm.If signal strength is weak, it is useful to face a directional antenna at the closest radio base station. This can increase the strength of the signal received by the radio device.The radio device’s peak output power can reach 2 W. RF field strength varies with antenna type and distance. At 10 cm from the antenna the field strength may be up to 70 V/m and at 1m it will have reduced to 7 V/m.
8. HINTS FOR INTEGRATING THE RADIO DEVICE59LZT 123 7589 R1AIn general, CE-marked products for residential and commercial areas, and light industry can withstand a minimum of 3 V/m.8.3.4 The Antenna CableUse 50 Ω impedance low-loss cable and high-quality 50 Ω impedance connectors (frequency range up to 2 GHz) to avoid RF losses. Ensure that the antenna cable is as short as possible.The Voltage Standing-Wave Ratio (VSWR) may depend on the effectiveness of the antenna, cable and connectors. In addition, if you use an adapter between the antenna cable and the antenna connector, it is crucial that the antenna cable is a high-quality, low-loss cable.Minimize the use of extension cables, connectors and adapters. Each additional cable, connector or adapter causes a loss of signal power.8.3.5 Possible Communication DisturbancesPossible communication disturbances include the following:•Noise can be caused by electronic devices and radio transmitters.•Path-loss occurs as the strength of the received signal steadily decreases in proportion to the distance from the transmitter.•Shadowing is a form of environmental attenuation of radio signals caused by hills, buildings, trees or even vehicles. This can be a particular problem inside buildings, especially if the walls are thick and reinforced.•Multi-path fading is a sudden decrease or increase in the signal strength. This is the result of interference caused when direct and reflected signals reach the antenna simultaneously. Surfaces such as buildings, streets, vehicles, etc., can reflect signals.•Hand-over occurs as you move from one cell to another in the GSM network. Your mobile application call is transferred from one cell to the next. Hand-over can briefly interfere with communication and may cause a delay, or at worst, a disruption.
9. EMBEDDED APPLICATIONS60LZT 123 7589 R1A9. Embedded ApplicationsThe radio device has the capability to store and run customer written code in the form of a script during the processor’s idle time, through the use of an on board interpreter.9.1 FeaturesMain features of embedded applications are as follows.• C based scripting language (Sony Ericsson specific);• Over the air upgrade of scripts (NOT GSM software);• Library of intrinsic functions;• 2 scripts can be stored in the memory at any time but only 1 can be active.9.2 ImplementationThe radio device has up to 44k of space available for storage of two scripts in the scripting language and 25k of operating RAM. Structures included in this language are:• If - then - else statements• While loops• For loopsAll hardware interfaces that are normally available to the radio device through the AT commands are available to the embedded application. Further drivers have been written such as M bus, keypad, SPI and I2C for use by the embedded application (EA) through the use of the I/O pins.9.2.1 LimitationsSince the radio device is processing the script using its own memory, limitations are placed onto the scripts that are run.• A direct comparison cannot be made to a fully compiled C program in terms of size but a gauge of script size is that if each line were 128 characters long in the script then the script could be 350 lines long. • Processing power is something that needs to be considered as the script is run as a low priority process within the software. However, controller mode stops GSM operation and provides all the processing power for the script to be run. See the M2mpower Application Guide for more details.• Code cannot be ported directly from an existing application and loaded directly onto the radio device. It must be re written in the Sony Ericsson Mobile script language so that the radio device interpreter can function correctly.
9. EMBEDDED APPLICATIONS61LZT 123 7589 R1A9.2.2 M2mpower IDE (Integrated Development Environment)The IDE is a Windows based package which allows the user to write, simulate, debug and download the application into a radio device with the embedded application (EA) software. The standard version is designed to run on Windows XP and 2000, other versions are available for 98 if required.The M2mpower Application Guide is available for implementing applications using the developer’s kit and the embedded application (EA) functionality.This is a required package to be able to implement an embedded application (EA).For further information please contact Sony Ericsson Mobile Communications customer support.
10. TCP/IP STACK62LZT 123 7589 R1A10. TCP/IP StackAn on board IP/TCP/UDP stack has been integrated into the software negating the need for the customer to implement one in their own code base.This is only accessible by using an embedded applications (see section 9) using intrinsic functions.10.1 ImplementationThe following types of commands allow various functions:• Open/closing IP connection - Negotiates/closes a dynamic IP address with the web server.• Send/Receive TCP packets - Performs all TCP operations to send and receive packets.• Send/Receive UDP packets - Performs all UDP operations to send and receive packets.• Resolve URL to an IP address - Similar to nslookup command in DOSWhen the unit is set up and controlled using the embedded applications either the embedded applications or an external application can generate data to be sent and pass it to the radio device for transmission.This effectively provides a transparent communication link from the application to an internet server over GPRS.
11. TECHNICAL DATA63LZT 123 7589 R1A11. Technical DataMechanical SpecificationsPower supply voltage, normal operationRadio specificationsSIM cardMaximum length 50 mmMaximum width 33 mmMaximum thickness 6.82 mm(excluding connector pins and top of antenna connector)Weight 18.5 gVolt age 3.6 V nominal (3.4 V - 4.0 V)Ripple < 100 mV @ <200 kHz; < 20 mV @ > 200 kHzVoltage must always stay within a normal operating range, ripple includedPower consumption Voice/CSD: < 250 mA (< 2 A peak)Data (GPRS 4+1); < 350 mA (< 2 A peak)Idle mode: < 5 mASwitched off: < 100 µAFrequency range GR47: E-GSM 900 MHz and GSM 1800 MHz (dual band) GR48: GSM 850 MHz and GSM 1900 MHz (dual band)Maximum RF output powerGR47: 900 MHz, Class 4, 2 W; 1800 MHz Class 1, 1 W GR48: 850 MHz, Class 4, 2W; 1900 MHz Class 1, 1 WAntenna impedance 50 Ω 3 V or 5 V Support of external SIM card
11. TECHNICAL DATA64LZT 123 7589 R1AEnvironmental specificationsData StorageOperating temperature range (full specification)-10 °C to +55 °COperating temperature range (working)-30 °C to +75 °CStorage temperature range-40 °C to +85 °CMaximum relative humidity95 % at +40 °CStationary vibration, sinusoidalDisplacement: 7.5 mmAcceleration amplitude: 20 m/s² and 40 m/s²Frequency range: 2-8 Hz, 8-200 Hz, 200-500 HzStationary vibration, randomAcceleration spectral density (m²/s²): 0.96, 2.88, 0.96Frequency range: 5-10 Hz, 10-200 Hz, 200-500 Hz, 60 min/axisNon-stationary vibration, including shockShock response spectrum I, peak acceleration: 3 shocks in each axis and direction; 300 m/s², 11 msShock response spectrum II, peak acceleration: 3 shocks in each axis and direction; 1000 m/s², 6 msBump Acceleration: 250 m/s²Free fall transportation 1.2 mRolling pitching transportationAngle: ±35 degrees; period: 8 sStatic load 10 kPaLow air pressure/high air pressure70 kPa/106 kPaSMS storage capacity 40 in ME In addition, the unit can handle as many SMS as the SIM can storePhone book capacity 100
12. DECLARATION OF CONFORMITY65LZT 123 7589 R1A12. Declaration of Conformity
Product Photo/Illustration Developer’s Kit
DRAFT 67LZT 123 7589 R1A13. Introduction to the Developer’s KitThe developer’s kit for the radio devices is designed to get you started quickly. It contains all the hardware you will need to begin the development of an application. The only items you need to provide are; a computer, a SIM card and network subscription, and a knowledge of programming with AT commands.1RWH Before connecting up and using the developer’s kit, we strongly recommend you read “Integrating the Radio Device”, page 16 and all of this section. There are many switches, jumpers and connector options in the developer’s kit. A knowledge of the functionality of the radio device is therefore essential before you start altering the hardware settings.The main hardware in the developer’s kit is a box, containing a board onto which you plug the radio device. Connectors, switches, jumpers and SIM card holder are provided to allow you to configure and access all the functions of the radio device.13.1 Contents of the KitPlease take the time to check the contents of your kit against the list shown below. If any of the items are missing contact your supplier immediately.Developer’s kit - Part Number DPY 102 225Description Product Number QtyRadio Device:GR47 orGR48DPY 102 220DPY 102 2221GR47/GR48 developer’s kit (box and development board)KRY 101 1919 1Switched mode PSU 12 V d.c. BML 161 1014 1UK mains plug KRY 111 087 1European mains plug KRY 111 086 1USA mains plug KRY 111 088 19 pin serial connector cable RPM 113 7796 1Headset RLF 501 40 1Quad band antenna KRE 101 1970 1Data carrier/CD-ROM containing:Software Manual;Integrator’s ManualLZY 214 2583 1
13. INTRODUCTION TO THE DEVELOPER’S KIT68LZT 123 7589 R1A13.2 General Functioning of the KitThe following block diagrams are provided to help you understand the general principles of operation of the developer’s kit.You can use the kit’s connectors to access and control the radio device (all switches and jumpers in their default positions).Figure 13.1 shows the various on-board voltages and how they are fed to the radio device and other circuitry. The developer’s board is powered by an external power supply connected to Vcc, see below. The power to the developer’s board circurity is selectable from internal or external 3V6 source.Figure 13.1 Power supply connection and the on-board voltagesVIOLEDVIOGR47orGR48VCCDGNDVCCSwitchn/c5V? 32VDC JackExternal3.6VTo Development board andinterface circuitsINT EXT3V6Reg
13. INTRODUCTION TO THE DEVELOPER’S KIT69LZT 123 7589 R1AFigure 13.2, Figure 13.3 and Figure 13.4 show how various signals are routed on the developer’s board. Thicker lines indicate multiple signals.Figure 13.2 Miscellaneous signals, connection and routingFigure 13.3 Audio signals, connection and routingX3X2X1Status LEDOn/OffSIMSIMHeaderI2CGPIO3V6VIOOn/Off &PSU ControlGPIOLEDDAC/ADC1-5I2CTX_ONSIMVRTCAFMSEAR3.5mm socketATMSMIC3.5mm socketPCMPCM6 pin headerBUZZERBuzzerMICN, MICP, BEARN, BEARPRJ9 connectorHandsetX1
13. INTRODUCTION TO THE DEVELOPER’S KIT70LZT 123 7589 R1AFigure 13.4 Comms signals, connection and routingX3X2UART1FlowControlDSR, RI, DTR,CTS, RTS, DCDTD, RDTD2, RD2TD3, RD3UARTSERVICE LEDSERVICEX1
14. USING THE DEVELOPER’S KIT71LZT 123 7589 R1A14. Using the Developer’s KitThis section provides you with the information needed to setup and use the developer’s kit. Before changing switch and jumper settings, refer to “14.3 Jumpers”, page 74.Front and rear views of the developer’s kit are shown below. Use a flat blade screwdriver to unhinge the side clips of the kit and lift the plastic lid off to access the inside. Figure 14.1 Front viewFigure 14.2 Rear viewEXT VCC RFGR47 / GR48 Developer's KitSony EricssonHANDSETOnOffStatusVIOMIC EAR5 - 32V DCVCCEXTN/CINTUART
14. USING THE DEVELOPER’S KIT72LZT 123 7589 R1A14.1 Start up Check ListTo use the developer’s kit in standard format check the following:• With the case lid removed, make sure the radio device is plugged into X1 and the RF lead is connected to the MMCX socket of the radio device;• Add your SIM card;• Check the jumpers are in their default positions. Refer to Figure 14.3;• Connect the serial cable between your computer and the UART connector on the rear panel;• Connect the antenna to the RF connector on the front panel;• Connect the audio equipment if required;• Plug the external power supply into the socket marked 5-32V DC on the rear panel;• Switch Vcc to INT;• Push ON/OFF for at least 2 seconds until the yellow VIO LED is on.Your developer’s kit should now be operational and ready to receive AT commands.
14. USING THE DEVELOPER’S KIT73LZT 123 7589 R1A14.2 Developer’s Board OverlayFigure 14.3 shows the developer’s board, including the position of all the connectors, switches and jumpers (default positions). Figure 14.3 Developer’s board overlayPCMATMSGNDSIM+U7INTSCLP2P0P4P6U5VRTCLEDSRVC2PORTTD1SHDNBAUDU4X4DTRBUZZERX7OUTULDSYNGND40DATCLKVCCSERIAL NUMBERA1A0A2SonyEricssonX9C15DATAU1P1P3P7P5SW1SHDNGNDCHG EXTGNDTO_INEXTSW2INTR1R3U8R2R4C2C0C4D21C1C3TD3RD3TD2RD2WAKEDIS12DCDRTSCTSX83V6LS1RIINDSRDLDCLKX63940PR#39VPPX5X2X3RST
14. USING THE DEVELOPER’S KIT74LZT 123 7589 R1A14.3 JumpersAll jumpers are located on the developer’s board (see “Developer’s board overlay”, page 73).3RZHUDQG&RQWURO8$57Jumper Default DescriptionINT/EXT INT Selects which voltage path supplies the DK support circuitry (not the supply to the radio device).INT selects power from the internal +3.6V DC supply.EXT selects power from the EXT VCC connector.TO_IN - With jumper TO_IN fitted, the DK and the radio device will automatically power-up as soon as power is applied to DC Jack X9.SHDN -With jumper SHDN fitted, the internal +3.6V power supply will be disabled.Note: There is a second jumper labelled ’SHDN’ which is in the UART area (by X4).VRTC Fitted This jumper connects the DK real-time-clock backup capacitor to the VRTC pin of the radio device.Jumper Default DescriptionSRVC -When fitted, the module will be operated in ’Service’ mode enabling system-status logging from the radio device.The red ‘Service’ LED will be illuminated.PORT - When fitted, switches the serial port from the 'AT' command port UART1 to UART2/UART3. Note: Use the PORT jumper link in conjunction with links “TD2/TD3” and “RD2/RD3” to select between UART2/UART3.TD2/TD3 -This dual jumper selects the TD (Transmit Data) line for either UART2 or UART3 as the alternative serial port when jumper 'PORT' is fitted. The jumper connects TD2 or TD3 to the centre pin to make the selection. See “Connectors”, page 80 for more details.Note: When UART2 or UART3 is used via the application connector, the TD2 or TD3 jumper must be removed to avoid circuit conflicts within the DK.RD2/RD3 - This dual jumper selects the RD (Receive Data) line for either UART2 or UART3 as the alternative serial port when jumper 'PORT' is fitted. The jumper connects RD2 or RD3 to the centre pin to make the selection. See “Connectors”, page 80 for more details.Note: When UART2 or UART3 is used via the application connector, the RD2 or RD3 jumper must be removed to avoid circuit conflicts within the DK.
14. USING THE DEVELOPER’S KIT75LZT 123 7589 R1ADIS -When fitted, the serial port driver IC disables the receiver buffers that normally drive UART signals into the radio device. This will prevent the radio device from receiving data through the serial port.WAKE - When fitted, the radio device will automatically power-up when the UART DTR signal is driven high. This allows a convenient mechanism for an external host computer to switch on the module. The DTR signal must be driven low or negative before the module can be switched off under software command.Note: If DTR is not driven low or negative and the host computer commands the module to shut-down, the DTR signal in its high state will immediately indicate that the module is to switch back on.BAUD -When fitted, this jumper allows the serial port driver IC to operate at baud rates in excess of 250 kbps and up to 1 Mbps.Note: There will be an increase in current consumption with this option selected.SHDN - When fitted, the serial port IC is forced into a low power state with the internal transmitters disabled. In the shut-down state the radio device will still receive commands but any transmission attempts from the radio device will be blocked by the serial port IC.Notes: In the shut-down state all the hardware flow control transmitters will be switched off. In order to send commands to the radio device in this state, the host computer must also have hardware flow control switched off.There is a second jumper labelled ’SHDN’ which is in the Power Supply area (adjacent to U7).Jumper Default Description
14. USING THE DEVELOPER’S KIT76LZT 123 7589 R1A$XGLRDQG3&00LVFHOODQHRXVJumper Default DescriptionULD To OUT To enable analog audio microphone path ULD must be connected to OUT using the jumper.OUT To ULD To enable analog audio microphone path OUT must be connected to ULD using the jumper.DLD To IN To enable analog audio earpiece path DLD must be connected to IN using the jumper.In To DLD To enable analog audio earpiece path IN must be connected to DLD using the jumper.SYN - This is an output connection for the PCM synchronisation signal from the radio device.CLK -This is an output connection for the PCM clock signal from the radio device.BUZZER Fitted When fitted, this link enables the DK buzzer driver circuitry.Jumper Default DescriptionDSR Fitted Connects serial port flow control signal DSR between UART connector X4 and radio device.Note: DSR is a dual function signal from the radio device. When this signal is being used for any other purpose (e.g. Keypad or application specific through X2 or X3), this jumper must be removed.RI Fitted Connects serial port control signal RI between UART connector X4 and radio device.Note: RI is a dual function signal from the radio device. When this signal is being used for any other purpose (e.g. Keypad or application specific through X2 or X3), this jumper must be removed.DTR Fitted Connects serial port flow control signal DTR between UART connector X4 and radio device.Note: DTR is a dual function signal from the radio device. When this signal is being used for any other purpose (e.g. Keypad or application specific through X2 or X3), this jumper must be removed.CTS Fitted Connects serial port flow control signal CTS between UART connector X4 and radio device.Note: CTS is a dual function signal from the radio device. When this signal is being used for any other purpose (e.g. Keypad or application specific through X2 or X3), this jumper must be removed.RTS Fitted Connects serial port flow control signal RTS between UART connector X4 and radio device.Note: RTS is a dual function signal from the radio device. When this signal is being used for any other purpose (e.g. application specific I/O through X2 or X3), this jumper must be removed.
14. USING THE DEVELOPER’S KIT77LZT 123 7589 R1ADCD Fitted Connects serial port control signal DCD between UART connector X4 and radio device.Note: DCD is a dual function signal from the radio device. When this signal is being used for any other purpose (e.g. Keypad or application specific through X2 or X3), this jumper must be removed.TD Fitted Connects serial port Transmit Data signal TD between UART connector X4 and radio device.Note: It is only valid to have one Transmit Data buffer in the circuit. If TD is driven by the application through connector X2 or X3, this jumper must be removed to avoid circuit conflicts.LED Fitted When fitted, this enables the STATUS LED to be illuminated by signal LED from the radio device.Note: LED is a dual function signal in the radio device. When this signal is being used for any other purpose (e.g. application specific I/O through X2 or X3), it is recommended that this jumper is removed to avoid circuit conflicts or unexpected circuit behavior.SCL - When fitted, connects the I2C clock signal from the radio device to the GPIO interface IC, U5. Note: Use the address selectors A0-A2 to set GPIO interface I2C address. Ensure that the selected address is unique to all I2C devices using SCL and SDA from radio device.DATA -When fitted, connects the I2C data signal from the radio device to the GPIO interface IC, U5. Note: Use the address selectors A0-A2 to set GPIO interface I2C address. Ensure that the selected address is unique to all I2C devices using SCL and SDA from radio device.A0 - When fitted, connects address pin A0 of IC U5 to logic high. When the jumper is not fitted, address A0 is held to logic low by the DK. Note: IC U5 address range is 0x70 to 0x7F.A1 -When fitted, connects address pin A1 of IC U5 to logic high. When the jumper is not fitted, address A1 is held to logic low by the DK. Note: IC U5 address range is 0x70 to 0x7F.A2 - When fitted, connects address pin A2 of IC U5 to logic high. When the jumper is not fitted, address A2 is held to logic low by the DK. Note: IC U5 address range is 0x70 to 0x7F.
14. USING THE DEVELOPER’S KIT78LZT 123 7589 R1A14.4 SwitchesAll switches are mounted on the front panel of the developer’s box.Switch Default DescriptionVcc(SW1)N/C This switch chooses the voltage source that the radio device will use. The default state N/C makes the voltage path to the radio device open circuit. Choosing INT connects the internal +3.6V DC supply to the VCC pins of the radio device. Choosing EXT connects the external +3.6V DC supply to the VCC pins of the radio device.Note: The external +3.6V DC supply is a user provided source through the EXT VCC connector.ON/OFF(SW2)- This is a momentary push-button switch to enable the user to manually turn the module on and off. The radio device is turned on by pressing and holding the ON/OFF switch for at least 1 second before releasing.The radio device is turned off by pressing and holding the ON/OFF switch for at least 2 second before releasing. The module will detect the OFF request and the software will perform all the necessary shutdown tasks (e.g. SIM power management and network detach) before the VIO LED is extinguished.Note: In the event of the radio device locking up and being unrecoverable under software control, the ON/OFF switch provides an alternative HARD SHUTDOWN control. To initiate the HARD SHUTDOWN feature press and hold the ON/OFF switch for at least 10 seconds or until the module powers down and VIO LED is no longer illuminated.
14. USING THE DEVELOPER’S KIT79LZT 123 7589 R1A14.5 HeadersHeader Connections DescriptionPCM ULD, DLD, OUT, IN, SYN, CLKCarries digital audio PCM signals for access by user application.Note: In order for analog audio to be created internally by the radio device, signal ULD must be connected to OUT for the MIC path and signal DLD must be connected to IN for the EAR path.SIM VCC, RST, CLK, VPP, DAT, PR#, GNDThis connector allows access to the SIM interface signals. These test points are connected in parallel with SIM connector ’X5’.Note: If this header is used to attach to an external SIM, an internal SIM fitted into connector ’X5’ must be removed.KEYPAD C0, C1, C2, C3, C4, R1, R2, R3, R4This header provides all the connections required to connect to a standard 20 key (5 columns x 4 rows) keypad matrix. ’C#’ are output drivers to connect to keypad columns. ’R#’ are input receivers to connect to keypad rows.Note: C0 is a virtual keypad column driver and is simply a connection to ground. C0 therefore does not appear on the radio device as a keypad driver output. The keypad interface recognises when the rows (R1-R4) are connected logic ’low’. If this is registered while the columns (C1-C4) are idle then it is accepted that the ’active’ column is C0 (column zero).I2C GPIO P0, P1, P2, P3, P4, P5, P6, P7, INTThis header provides a general purpose I/O port from the I2C to GPIO interface. P0-P7 are the 8 bits of the data port. INT is the interrupt output of the interface. The interface IC which drives these signals is part number PCF8574AT from Philips Semiconductor.ATMS ATMS In addition to being able to feed in a microphone signal from an alternative source, this pin can be used to answer an incoming telephone call. By momentarily connecting this signal to GND when an incoming call is ’ringing’, the radio device will ’answer’ the call.GND GND These two headers can be used as the signal reference ground for test and measurement.
14. USING THE DEVELOPER’S KIT80LZT 123 7589 R1A14.6 ConnectorsConnector Type DescriptionRADIO DEVICE ‘X1’60 PinDual Row0.05” pitchThe radio device is 'plugged-in' to the development kit. This allows direct connection of the module to the development board.APPLICATION‘X2’40 PinDual Row0.1” pitchThis 40-pin connector is compatible with standard 0.1" pitch mating connectors and with 0.05" pitch IDC ribbon cable connectors. This allows the user a range of connection methods to interface to the application. This connector is wired in parallel with application connector 'X3', which can be used for test probing or to wire patch alternative signals into the four 'N/C' pins.APPLICATION’X3’40 PinDual Row0.1” pitchThis 40-pin connector is compatible with standard 0.1" pitch mating connectors and with 0.05" pitch IDC ribbon cable connectors. This allows the user a range of connection methods to interface to the application. This connector is wired in parallel with application connector 'X2', which can be used for test probing or to wire patch alternative signals into the four 'N/C' pins.UART'X4’9-pin D Female SocketThis is a full 9-pin RS232 compatible communication port. Using jumpers on the DK, this connector may be used for UART1, UART2 or UART3 of the radio device.Note: UART2 and UART3 of the radio device are considered 3-wire interface only. The hardware flow and other control signals which are passed through this connector are only relevant when used with UART1.SIM'X5’Latch and lift style holder with integral SIM detect contactThis is a standard holder for a GSM SIM card. The top piece slides towards “Open” and then lifts to release or insert the SIM card using the integral guide rails. To close, lower the pivoting top piece flush with the bottom piece and slide the top towards “Lock”.DCDRDRTSTDCTSDTR127384659RIDSR
14. USING THE DEVELOPER’S KIT81LZT 123 7589 R1AHandset ‘X6’RJ9 socket Connector for a standard telephone handset. Carries signals from the balanced outputs BEARN and BEARP and to the balanced inputs MICN and MICP. To enable an analog audio link it is necessary to link PCM signals “ULD to OUT” and “DLD to IN” using jumper links on the PCM header.Note: The PCM links to enable analog audio are fitted by default but may have been removed during customer development. There will be no analog audio without these links. Please check carefully.EAR'X7'3.5mm Stereo JackSocketThis is a standard unbalanced audio output (AFMS) which is compatible with a standard PC-style stereo headset.Note: This MONO audio signal is fed to both left and right channels of the stereo connector. To enable this analog audio link it is necessary to link PCM signal DLD to signal IN using a jumper link on the PCM header.Note: The PCM links to enable analog audio are fitted by default but may have been removed during customer development. There will be no analog audio without these links. Please check carefully.MIC'X8'3.5mm Stereo JackSocketThis is a standard unbalanced audio input (ATMS) which is compatible with a standard PC-style microphone.Note: Microphone bias voltage is provided through this connector in the range 2.0VDC to 2.5VDC.To enable this analog audio link it is necessary to link PCM signal ULD to signal IN using a jumper link on the PCM header.Note: The PCM links to enable analog audio are fitted by default but may have been removed during customer development. There will be no analog audio without these links. Please check carefully.5 - 32V DC'X9'2.1mm DC Jack SocketAllows connection of an external power supply in the voltage range +5.0VDC to +32.0VDC at 4 Watts.Connector Type Description1234ground earearground micmic
14. USING THE DEVELOPER’S KIT82LZT 123 7589 R1A14.7 LED IndicatorsEXT VCC 3 pin CircularThis connector carries three signals: EXT VCC (1); CHG_IN (3); GND (2). (These signals are wired into PCB holes labelled EXT, CHG, GND respectively).EXT VCC must be a +3.6VDC source capable of supplying up to 2.0A. This can be a battery source.CHG_IN can be a +5.0VDC source capable of supplying 600mA maximum.GND is the ground reference to be used by the external supplies.Note: If battery charging is enabled the charging source must be capable of supplying the required charging current but the charging current must not exceed 500mA.RF SMA Panel SocketConnect the supplied antenna.LED (Colour)Location DescriptionStatus(Green)Front Panel This LED is enabled by fitting the “LED” jumper link (located between the internal power supply and the keypad header).The LED is driven on by a signal from the radio device pin 33 (LED/IO6).When the radio device connection “LED/IO6” is configured as the LED driver this LED signifies the module and network status as follows; ON - Module cannot connect to a network.FLASHING - MODULE has SIM fitted and is locked onto a valid GSM network. VIO(Yellow)Front Panel This LED is illuminated when the radio device is switched on. The module outputs +2.75VDC on signal VIO (pin 34).SRVC(Red)PCB When the SRVC jumper link is fitted and the DK has +3.6VDC power, this LED illuminates to indicate that SERVICE mode is activated.3V6(Green)PCB When the DK has +3.6VDC power, this LED will illuminate.Note: The DK +3.6V and the radio device VCC inputs are connected through switch VCC (SW1) on the front panel. The 3V6 LED does NOT indicate that the module has power applied to its VCC connections.Connector Type Description213
14. USING THE DEVELOPER’S KIT83LZT 123 7589 R1A14.8 System Connector Pin AssignmentsRefer to the table below when monitoring signals on, or connecting to, X1. The table shows the system-connector pin assignments for the radio devices. See “System Connector Interface”, page 19for more details.Figure 14.4 System connector pin assignments1VCC DGND 23VCC DGND 45VCC DGND 67VCC DGND 89VCC DGND 1011 CHG_IN DGND 1213 IO5/ADC4 ON/OFF 1415 SIMVCC SIMPRESENCE 1617 SIMRST SIMDAT 1819 SIMCLK DAC 2021 IO1/KEYROW2 IO2/ADC5 2223 IO3/KEYROW3 IO4/KEYROW4 2425 VRTC ADC1 2627 ADC2 ADC3 2829 SDA SCL 3031 BUZZER DSR/O3/KEYCOL3 3233 LED/IO6 VIO 3435 TX_ON RI/O2/KEYCOL2 3637 DTR/IN1/KEYROW1 DCD/O1/KEYCOL1 3839 RTS/IO9 CTS/O4/KEYCOL4 4041 TD RD 4243 TD3/IO7 RD3/IO8 4445 TD2 RD2 4647 PCMULD PCMDLD 4849 PCMOUT PCMIN 5051 PCMSYNC PCMCLK 5253 MICP MICN 5455 BEARP BEARN 5657 AFMS SERVICE 5859 ATMS AGND 60
14. USING THE DEVELOPER’S KIT84LZT 123 7589 R1AFigure 14.5 Pin Orientation and Board assignmentsFigure 14.6 Application Interface Connector (X2 and X3) - Pin AssignmentPCMSIMINTP2P0LEDTDDTRBUZZEROUTULDSYNGNDDATCLKVCCA1A0A2X9P1P3SW1GNDCHG EXTGNDEXTSW2INTR3U8R4C2C4D21C31DCDRTSCTSRIINDSRDLDCLK39PR#VPPX5X2X3RSTAudioUART+3.6V internalpower supplyKeypadinterfaceApplicationinterfaceBuzzerSIMICtoGPIO2125960X1 pin numbering viewed from the front of the developer's kit.VCCDGNDON/OFFHR_INIO1 / KEYROW2IO3 / KEYROW3VIOIO5 / ADC4ADC2DACLED / IO6SDADGNDRXRTS / IO9DSR / KEYCOL3 / OUT3DCD / KEYCOL1 / OUT1TX2TX3n/cVCCDGNDTO INn/cIO2 / ADC5IO4 / KEYROW4DGNDADC1ADC3DGNDTXONSCLn/cTXCTS / KEYCOL4 / OUT4RI / KEYCOL2 / OUT2DTR / KEYROW1RX2RX3n/c13579111315171921232527293133353739246810121416182022242628303234363840

Navigation menu