Electronic Systems Technology ESTEEM192S Wireless Modem User Manual part 4

Download:
Mirror Download [FCC.gov]
Document ID	29976
Application ID	EP2oX+YpVgoKrh/wRVaKsg==
Document Description	user manual part 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.2kB (15037 bits)
Date Submitted	1999-03-31 00:00:00
Date Available	1999-05-14 00:00:00
Creation Date	2001-07-01 07:11:40
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-07-01 07:11:40
Document Title	user manual part 4

CHAPTER 4
ESTEEM APPLICATION PROGRAMS
TRANSPARENT AUTO CONNECT
TRANSPARENT AUTO CONNECT GLOBAL
INTERACTIVE TERMINAL APPLICATIONS
PROGRAMMABLE LOGIC CONTROLLERS
CHAPTER 4
ESTEEM APPLICATION PROGRAMS
Listed below are different application programs to aid the
user in programming the ESTeem.
TRANSPARENT AUTO-CONNECT
This mode is used for a dedicated point to point
application. The ESTeem will initiate the radio link when
data is received by the RS-232/422/485 port.
Perform the following prior to programming the ESTeem(s)
to initialize the unit to factory default settings:
1.
2.
3.
Turn Bit 2 OFF on the RS-232C Setup Switch.
Reset the ESTeem.
TYPE FA . Please note the characters may not be
echoed by the CRT.
ESTeem A
ESTeem B
---------------------------- -------------------------------ADD
xxx
ADD
yyy
SETC
yyy
SETC
xxx
TERMC
ON
TERMC
ON
TERMT
10
TERMT
10
XHF
ON *
XHF
ON *
DISACK
ON *
DISACK
ON *
TRANS ON
TRANS ON
SAVE
SAVE
Bit 8 ON
Bit 8 ON (RS-232 Switch)
Reset ESTeem
Reset ESTeem
1.
2.
3.
Turn Bit 2 OFF on the RS-232C Setup Switch
Reset the ESTeem.
TYPE FA . Please note the characters may not be
echoed by the crt.
ESTeem A
---------------------------------------------------ADD
xxx (xxx = ESTeem address)
SETCON
255
TERMC
ON
TERMT
10
XHF
ON *
TRANS ON
SAVE
Bit 2
ON (RS-232 Switch)
Reset ESTeem
Note:
Only hardware flow control can be used in this
mode.
Notes:
• Turn DISACK ON only if you want to defeat the
acknowledge packet.
• xxx and yyy represent an ESTeem address which is
user definable from 1 to 254.
TRANSPARENT AUTO-CONNECT
GLOBAL
This mode is usually used for a point to multi-point
applications when a customers devices include their own
addressing protocol to communicate between devices. The
ESTeem packet addressing and acknowledge protocol is
defeated. All ESTeems will receive the data transmission.
The 16 bit CRC error checking on received data is still
enabled. This program is used in all ESTeems, the only
difference is the unit addresses.
Perform the following prior to programming the ESTeem(s)
to initialize the unit to factory default settings:
Revised: 11 Feb 99
4-2
CHAPTER 4
ESTEEM APPLICATION PROGRAMS
INTERACTIVE TERMINAL APPLICATION
This program is used to connect a mainframe to a remote
terminal. This setup is a typical point to point configuration
with the AUTO-CONNECT feature enabled.
Perform the following prior to programming the ESTeem(s)
to initialize the unit to factory default settings:
1.
2.
3.
PROGRAMMABLE LOGIC
CONTROLLERS
EST has available complete Engineering Reports for each
PLC manufacturer make. These reports are available on our
web site at www.esteem.com or will be provided at no
charge by calling EST Customer Support on 509-735-9092.
Turn Bit 2 OFF on the RS-232C Setup Switch.
Reset the ESTeem.
TYPE FA . Please note the characters my not be
echoed by the crt.
ESTeem At Mainframe
---------------------------ADD
xxx
SETC
yyy
TERMC
ON
TERMT
10
XSF
OFF
XHF
ON *
DISACK
ON *
TRANS
ON
SAVE
Bit 2
ON
RESET ESTeem
ESTeem At Terminal
-------------------------ADD
yyy
SETC
xxx
TERMC
ON
TERMT
10
XSF
OFF
XHF
ON *
DISACK
ON *
TRANS
ON
SAVE
Bit 2 ON (RS-232 Switch)
RESET ESTeem
Notes:
• Turn DISACK ON only if you want to defeat the
acknowledge packet.
• Only hardware flow control can be used in this mode.
• xxx and yyy represent an ESTeem address which is
user definable from 1 to 254.
Revised: 11 Feb 99
4-3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:07:01 07:11:40
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:07:01 07:11:40+01:00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools