Electronic Systems Technology ESTEEM192S Wireless Modem User Manual appendix b

Electronic Systems Technology Wireless Modem appendix b

user manual appendix b

Download: Electronic Systems Technology ESTEEM192S Wireless Modem User Manual appendix b
Mirror Download [FCC.gov]Electronic Systems Technology ESTEEM192S Wireless Modem User Manual appendix b
Document ID30225
Application IDEP2oX+YpVgoKrh/wRVaKsg==
Document Descriptionuser manual appendix b
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize13.68kB (170961 bits)
Date Submitted1999-04-01 00:00:00
Date Available1999-05-14 00:00:00
Creation Date2001-06-29 16:41:34
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-06-29 16:41:35
Document Titleuser manual appendix b

APPENDIX B
SPECIFICATIONS
Model 192S Specifications
LED INDICATORS
•
•
•
•
•
•
Power On
Receiver Carrier Detect
Transmitter Enable
Link Connect/Disconnect
Auto Connect Enable
RS-232/422/485 Framing Error
I/O – CONNECTORS
•
•
•
•
•
RS-232C/422/485 - 25 Pin Sub D
Female
Infrared Programming Port
RJ 11 Phone Interface (optional)
Antenna Output – TNC-R
Input Power - 2 Pin Molex
Female
DATA TRANSMISSION
PROTOCOL
•
ERROR CHECKING
•
1 to 254
DATA INPUT
•
•
•
•
•
RS-232/422/485 Asynchronous
Selectable 1,200 to 57,600 baud
7 to 8 data bits
Even, Odd or no parity
One or Two Stop Bits
DATA BUFFERS
•
•
16 Bit Cyclic Redundancy check
(CRC) with Packet Acknowledge
and Retry
FREQUENCY OF
OPERATION
•
•
ADDRESSING RANGE
•
Carrier Sensed Multiple Access
with Collision Detection (CSMACD)
2.4 to 2.462 GHz.
Frequency selectable in 11
frequency zones
RF DATA RATE
•
85.5K, 171K, 344K, or 688K bps
RF data rate (user selectable)
1 Watt RF output
100% duty cycle
50 ohms output impedance
Protocol activated keying
<1 ms typical latency
Direct sequence spread spectrum
Transmit 4000 bytes
Receive 4000 bytes
Hardware or Software
Revised: 11 Feb 99
•
Double conversion superheterodyne
-93 dBm 8E-2 Frame Error Rate
80 dB Image Rejection
> 35 dBm Adjacent Channel
Rejection
Four levels of squelch (software
programmable)
POWER REQUIREMENTS
•
11-16 VDC @ 700 ma Transmit
290 ma Receive
SIZE
•
2.45 in. Height
8.16 in. Width
9.37 in. Length
•
•
5 lbs.
Rugged die cast aluminum case
ENVIRONMENT
FLOW CONTROL
•
•
•
•
•
WEIGHT:
TRANSMITTER
•
•
•
•
•
•
RECEIVER
APX B-1
•
•
-30° to 50° C
95% Non-condensing
WARRANTY
1 Year
APPENDIX B
SPECIFICATIONS
Model 192S Antennas
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front To Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Antenna Envelope:
Weight:
AA01S
Omni-Directional, right angle rubber duck, ½ wave
Back of ESTeem Model 192S mount.
2400 to 24825 MHz
Vertical
50 ohms
3 dBd
< 1.5
n/a
n/a
n/a
Rubber duct whip.
n/a
TNC-R Male
4 in. length by 1.5 in width
.08 lbs.
4 in.
1.5 in.
Model AA01S
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front To Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Antenna Envelope:
Weight:
AA20S
Omni Directional, 5/8 Wave over 5/8 Wave over ¼ Wave.
Fixed base or mobile mount.
2400 to 2485 MHz
Vertical
50 ohms
5 dBd
< 1.5
n/a
n/a
n/a
Stainless steel whip. All other hardware anodized metal.
Stainless steel clamps for mounting to ¾ in. to 1½ in. pipe
with right angle mount of direct panel mount..
N Female.
9 in. length by 3.5 in. width
.4 lbs.
9 in.
3.5 in. Dia.
Right Angle
Mounting
Bracket
Stanless
Steel
Clamps
Model AA20S
Revised: 11 Feb 99
APX B-2
APPENDIX B
SPECIFICATIONS
Model 192S Antennas
Model No:
Antenna Type:
Applications:
Frequency:
Polarization:
Impedance:
Gain:
VSWR:
Front To Back Ratio:
Horizontal Beamwidth:
Vertical Beamwidth:
Antenna Material:
Mounting Hardware:
Antenna Connector:
Maximum Power Input:
Antenna Envelope:
Windload (RWV):
Wind Load ½ in. Ice:
Wind Surface Area:
Weight:
Revised: 11 Feb 99
AA202S
Directional, 15 element yagi in sealed UV
stable radome
Fixed base.
2400 to 2500 MHz
Linear
50 ohms
13.9 dBd
< 1.5
18 dB
34 degrees
30 degrees
Stainless hardware with one piece copper
radiating element. Advanced microwave
substrate. All other hardware anodized
metal.
Stainless steel U bolts for mounting to 1.5
in. to 2.2 in. diameter pipe.
N Female on UltraLink® Pigtail
50 Watts
26 in. length by 4.0 in. height by 1.5 in. width
125 mph
100 mph
0.4 ft
1.25 lbs.
APX B-3
Model AA202S

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:06:29 16:41:34
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:06:29 16:41:35+01:00
Page Count                      : 3
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ENPESTEEM192S

Navigation menu