Electronic Warfare Associates SRCED3 Remote Control Electronic Deadbolt User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2106495
Application ID	lhqmrixY97P4zsy2SsYqyg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.37kB (629686 bits)
Date Submitted	2013-10-30 00:00:00
Date Available	2013-10-31 00:00:00
Creation Date	2013-08-29 11:46:12
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-08-29 11:55:48
Document Title	Users Manual
Document Creator	Adobe InDesign CS6 (Windows)

REMOTE CONTROL ELECTRONIC DEADBOLT
PROGRAMMING & OPERATIONS MANUAL
DO NOT THROW AWAY UNTIL YOU HAVE
SAFELY STORED YOUR ADMIN CODE
LOCK INSTALLATION INSTRUCTIONS
1. Remove Existing Deadbolt
Parts List
First things first -- make sure have all of the necessary components in your
SimpliciKey package.
1 interior lock
1 interior plate
2 short bolts
2 long
wood screws
Next, remove the interior and
exterior lock components.
Finally, take out the existing deadbolt
slide assembly.
2 long bolts
2 strike wood
screws
First, remove the two interior screws
securing the lock.
2 short wood
screws
1 exterior lock
2. Check Cutout Size
1 strike plate
1 deadbolt lock
Critical Point
Stop to measure the cutouts for the lock
components. If the main cutout is 2-1/8 inches in
diameter, and latch cutout is 1 inch, you’re ready
to go. If not, you may need to use the Advanced
Guide to help you adjust your door.
2 keys
1 reinforcement
plate
2 remote control
keyfobs
1 strike box
2” Thickness Max
2 1/8”
1”
5. Install New Deadbolt
3. Remove Existing Strike Plate
First, remove the two existing strikeplate
screws.
Remove the strike plate and any other
hardware behind the plate.
Place deadbolt into door, check to see if
cross-hairs are centered.
Strike plate
To adjust the deadbolt length, twist the
deadbolt slide assembly to extend and
center in cutout.
4. Install New Strike Plate
Install the strike plate, then tighten screws.
For added security, and greater aesthetic appeal in the
door frame, install the strike box and reinforcement
plate. This may require additional door preparation to
make sure the strike plate remains flush with the door
frame.
Place strike plate into door frame to check that the
plate sits flush with the frame. Make sure the deadbolt freely slides into the strike plate when the door is
closed by rotating the thumbturn.
Make sure cross-hairs are on the
lower part of the assembly.
Strike plate
Deadbolt
Confirm that the deadbolt is aligned properly with the
strike plate by pressing the lock button on a remote
control keyfob with the door closed.
Standard Installation
Check that the plate sits flush
with the door.
Secure the deadbolt plate to the
door with two short wood screws
Correct
Insert the flat bar horizontally into the
cross-hairs of the deadbolt slide assembly.
Enhanced Security Installation
Strike plate
18
Critical Point
If the deadbolt is not properly aligned with the strike
plate, refer to the Advanced Guide to help you adjust
the strike plate position.
Strike wood screw
Incorrect
6. Install Exterior Lock
Slide the wires above the
deadbolt slide assembly.
Strike plate
Horizontal
flat bar
Strike box
Long wood screw
Reinforcement plate
Cross-hairs
0°
Long wood screw
Optional wood
screw hole for
increased
security.
Plastic clip
7. Install Interior Plate
9. Install Interior Lock
Slide wires through wire hole of
interior lock plate. Be sure to keep
wires out of the way by sliding both
wires into the plastic clip on the
interior plate.
Guide excess wiring into cavity above the green
circuit board. Align thumbturn with flat bar to
mount to interior plate. (Thumbturn must be in
the vertical position and deadbolt must remain
retracted). Attach interior lock to interior plate
with the two short bolts through holes under
battery case. Be careful not to pinch the wires
as you install the lock.
Insert two long bolts through plate,
latch, and thread into external lock,
securing all pieces snugly.
10. Test the Manual Deadbolt
J4
8. Attach Wires
Attach the black connector to the port
on the green circuit board with the
white rectangle around it labeled J4.
Attach other connector to the port on
the green circuit board just below the
top left screw. Connect Antenna is
labeled (see picture ).
Insert key into cylinder and turn to extend
deadbolt to locked position. If the deadbolt
will not extend, or there is resistance when
turning, double-check that all previous
steps have been completed successfully.
Remove key.
If the deadbolt still will not extend, call
Technical Support at 1-800-785-6595.
Critical Point
Connect Antenna Here
Critical Point
(A)
CONNECT ANTENNA
Correct
(B)
Incorrect
Do not skip this step or the lock
will not operate correctly.
Confirm that the deadbolt is retracted during the entire installation.
Thumbturn should be in a vertical
position with deadbolt retracted as
shown in (A).
Make sure the door is open and the deadbolt
is free to auto-locate. Do not press any buttons
until lock activity stops and confirmation tone
sounds.
11. Install Batteries
Install four AA batteries in the compartment
on interior lock.
Lock will automatically locate door position to
determine right-hand / left hand orientation
Slide battery cover into place, concealing the
battery compartment.
DAILY USE INSTRUCTIONS
REMOTE CONTROL KEYFOB INSTRUCTIONS
STOP! Test your keyfobs now before attempting to program.
1. Remote Control Keyfob
Critical Point
STOP! Test your keyfobs now before attempting to program.
SimpliciKey comes factory programmed with the keyfobs included
in the package. If the keyfobs are not registered with your lock, or to
add additional keyfobs (up to the maximum limit of 8), please see the
instructions on page 8.
Press to Lock
Press to Unlock
Your administration code (Admin Code) can be found on the
back of this booklet. The Admin Code can be changed by
following instructions on page 12.
The lock may time out if too much time passes between entering
commands. If this happens, you will need to start over.
Press
Command
2. Keypad Key Codes
For your security, SimpliciKey requires that you enter your own Key
Codes to activate this feature. Please see the instructions on page 9 to
add up to 16 Key Codes.
When Unlocked:
Enter your Key Code and Lock/ Unlock button (
) to lock
Key Code
When Locked:
Enter your Key Code and Lock/ Unlock button (
) to unlock
Key Code
3. Keypad Settings
For your convenience, the keypad has options for quiet operation and
faster locking, with instructions on page 10.
When simple lock is ON, pressing the Lock/Unlock button (
door.
) will lock the
When simple lock is OFF, the user will have to enter the Key Code
and press the Lock/Unlock button (
) to lock the door as shown above in
Step 2.
Add Remote Control Keyfob
1. Enter your Admin Code, press *
2. Enter “ADD FOB”, press *
3. The blue LED below the keypad
will begin to flash. You will have
nine seconds to register your keyfob.
4. While the blue light is flashing, press
both keyfob buttons for no more than 1
second. If you do not get the happy
tone, press both buttons immediately
again. If the tone is happy, then you’re
right, if it sounds like a chirp then start
over.
F -
Press and
hold
Delete an Individual Remote Control
Keyfob
1. Enter your Admin Code, press *
Test
both
Enter Admin Code
F -
2. Enter “DEL FOB”, press *
3. Press and hold either keyfob button
Delete all Remote Control Keyfobs
Enter Admin Code
1. Enter your Admin Code, press *
2. Enter “DEL FOBS”, press *
4. Manual Key Use
3. Repeat “DEL FOBS”, press *
SimpliciKey offers a bump-resistant 6-pin keyway should you choose
to use a metal key for entry.
4. Test the keyfobs to confirm
Test
both
Press and
hold either
4. Test the keyfob
When quiet lock is OFF, the keypad will emit softer tones during operation.
Enter Admin Code
F -
F -
Test
both
KEYPAD INSTRUCTIONS
KEYPAD INSTRUCTIONS
Critical Point
Critical Point
Your administration code (Admin Code) can be found on the
back of this booklet. The Admin Code can be changed by
following instructions on page 12.
Your administration code (Admin Code) can be found on the
back of this booklet. The Admin Code can be changed by
following instructions on page 12.
Press
Command
Add Key Code
Enter Admin Code
1. Enter your Admin Code, press *
C -
2. Enter “ADD CODE”, press *
NOTE: Code can be 4-7 digits
New Key Code
Test
5. Test the new Key Code, press
New Key Code
C -
2. Enter “DEL CODE”, press *
Key Code to Delete
Repeat
Key Code to Delete
Test
Enter Admin Code
1. Enter your Admin Code, press *
- L
C -
- L -
C -
2. Enter “DL CODES”, press *
3. Repeat “DL CODES”, press *
4. Test the deleted Key Codes,
press
Test
Delete Key Code
10
To turn on simple lock
To turn off simple lock
Enter Admin Code
1. Enter your Admin Code, press *
To turn sound ON, press 1, *
and repeat
To turn on sound
To turn sound OFF, press 2, *
To turn off sound
Master Reset Feature
Delete Key Code
Delete all Key Codes
2. Enter “SOUND” and press *
Enter
3. Enter the Key Code to be deleted,
press *
4. Repeat the Key Code to be deleted,
press *
5. Test the deleted Key Code,
press
Quiet Lock Feature
Turn on / off keypad sounds
Enter Admin Code
Delete a Key Code
1. Enter your Admin Code, press *
Enter Admin Code
To turn simple lock ON, press 1, *
and repeat
To turn simple lock OFF, press 2, *
and repeat
Repeat
*If error tone, start over
L/ UL Button (used for locking only)
2. Enter “LOCK” and press *
New Key Code
4. Repeat the new Key Code, press *
Simple Lock Feature
Enables
to lock
without entering a Key Code
1. Enter your Admin Code, press *
Enter
3. Enter the new Key Code, press *
Press
Command
Clears all stored codes, settings,
and remote control keyfobs.
All codes and keyfobs will need to
be reprogrammed after performing
this feature.
Critical Point
Remove one battery
Press and hold any
button and re-insert the
4th battery. Continue
holding button for about
5 seconds after battery
has been inserted
If the keypad flashes and a multi-tone alert
goes off at any point while in admin mode, you
have taken too long and will have to start over
from the first step.
11
CHANGING YOUR USER ADMIN CODE
Enter your Default Admin Code (see below) or the existing User Admin
Code and press the * key to begin Admin mode.
Default Admin Code
LOW BATTERY INDICATOR
When the 4 (AA) batteries get low, SimpliciKey will emit an alert tone and the low
battery indicator LED and exterior LED will flash for approximately 15 seconds.
Please be sure to replace your batteries at this time in order to ensure proper
operation of SimpliciKey.
Critical Point
If the keypad flashes and a multi-tone alert
goes off at any point in admin mode, you have
taken too long and will have to start over from
the first step.
Next, enter ADMIN (23646) on the keypad and press the * key.
Next, enter a new 4–6 digit Admin Code and then press the * key.
New Admin Code
Finally, repeat your entry of your new 4–6 digit Admin Code and then
press the * key.
New Admin Code
You will then receive the final confirmation tone and the keypad will flash
twice to let you know that the User Admin Code has been changed.
New Admin Code
We recommend that you write down
your new Admin Code here and keep
this manual in a safe place.
New Admin Code
WARNING: SimpliciKey submits that no lock,
by itself, can provide complete security. As
with other mechanical and electronic
locking devices, the security of this lock has
the potential to be compromised. We remind
all our customers to exercise good safety
procedures as part of your home security
plan. SimpliciKey locks are manufactured to
ANSI Grade 2 specifications. For added levels
of security, consult a qualified locksmith or
security expert.
12
DO NOT THROW AWAY UNTIL YOU HAVE SAFELY STORED YOUR ADMIN CODE
Exterior LED
Low Battery Indicator LED
13
INSTRUCTIONS FOR USE:
Always purchase the correct size and grade of battery
most suitable for the intended use.
Clean the battery contacts and also those of the device
prior to battery installation.
Ensure the batteries are installed correctly with regard
to polarity (+ and - ).
Remove batteries from equipment which is not to be
used for an extended period of time.
Remove used batteries promptly.
INSTRUCCIONES DE USO:
Compre siempre el tamaño y grado correcto de la batería
más adecuado para el uso previsto.
Changes or modifications not expressly approved by
SimpliciKey could void the user’s authority to operate the
equipment.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1)this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes : (1) l’appareil ne doit
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le
fonctionnement.
Limpie los contactos de la batería y también los del dispositivo
antes de la instalación de la batería.
Asegúrese que las baterías están instaladas correctamente
en relación con la polaridad (+ y -).
Retire las pilas del equipo que no va a ser utilizado durante
un período prolongado de tiempo.
Retire las pilas usadas.
14
15
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Notes:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
16
17
Troubleshooting Tips:
For additional tips and troubleshooting, please visit
Question
Solution
Why are the keyfob buttons
reversed? (lock button unlocks,
unlock button locks.)
Check to make sure the flat bar is horizontal through the cross-hairs during
installation. (page 5)
Why doesn’t the latch fully extend
when I rotate the thumbturn?
Check to make sure the flat bar is
horizontal through the cross-hairs
during installation. (page 5)
Why doesn’t the keypad respond
when I press the buttons?
Check to make sure the batteries
are charged and installed
properly.
Why doesn’t my pre-programmed
keyfob get a response from the
lock?
Check to make sure
the wires are inside
the clip and not
pinched during
installation. (page 6)
Why doesn’t the keypad respond
when I press the buttons?
Check to make sure both wires are
connected. (page 5)
Check that the batteries are installed
correctly.(page 6)
Why doesn’t my pre-programmed
keyfob get a response from the
lock?
Check to make sure both wires are
connected. (page 5)
Check that the batteries are installed
correctly.(page 6)
Why does the auto-locate feature
keep giving me an error tone
during installation?
Check that the deadbolt is retracted and
the thumbturn is vertical during
installation. (page 5)
Why does the lock give an error
tone when the door is closed and
lock button is pressed?
Manually check the deadbolt to make
sure it is aligned with the strike plate.
(pages 4, 6)
www.SimpliciKey.com
1 (800) 785-6595
Keep this code safe
Mantén este código
en un lugar seguro
Place Label Here
Coloca la etiqueta Aquí
Default Admin Code/Código Predeterminado de Administrador
Lifetime limited finish and mechanical warranty
2-year electronic warranty
Garantía limitada de por vida para el acabado y el
sistema mecánico
Garantía de 2 años para el sistema electrónico
This device complies with Part 15 of the FCC Rules.
operation is subject to the following two conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received,
including interference that may cause undesired
operations
© SimpliciKey 2013
18
DO NOT THROW AWAY UNTIL YOU HAVE
SAFELY STORED YOUR ADMIN CODE
Revision 3-2
19

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Create Date                     : 2013:08:29 11:46:12-04:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2013:08:29 11:55:48-04:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2013:08:29 11:55:48-04:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:21aa8f48-c79b-4c0b-b8c8-a6e4ad0c2a8c
Original Document ID            : xmp.did:5FE202D0787FE211B5D8AF3C548EA310
Document ID                     : xmp.id:5E9502F0C110E311AE24B74D825E4537
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:5D9502F0C110E311AE24B74D825E4537
Derived From Document ID        : xmp.did:68510C55BC10E311AE24B74D825E4537
Derived From Original Document ID: xmp.did:5FE202D0787FE211B5D8AF3C548EA310
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2013:08:29 11:46:12-04:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 10

EXIF Metadata provided by EXIF.tools