Electronics PA-PK Self-Contained Door Lock User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	150039
Application ID	F7BT3Iq0ewRLABvLU/zBjw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	263.51kB (3293934 bits)
Date Submitted	2001-05-15 00:00:00
Date Available	2001-05-07 00:00:00
Creation Date	2001-05-15 10:04:36
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2001-05-15 10:04:54
Document Title	Manual

Installation Instructions For
Low Profile Mortise Lock
A7454A
Table of Contents
Page
1 Warning .......................................................1
2 General Description .........................................2
3 Specifications ................................................2
4 Parts Breakdown............................................3-5
5 Features .......................................................5
6 Installation Instructions...................................6-13
7 Operational Check ..........................................14
8 Basic Programming Instructions .........................14
Keypad Only (100 Users–LK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Keypad or Proximity/Keypad (500 Users–LU or PK). . . . . . . . . . . . . . . 18
Proximity Only (500 Users–PA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9 Chain Programming ........................................23
10 Transaction Log .............................................24
1 Warning
Warning: Changes or modifications to this
unit not expressly approved by the party
responsible for compliance could void the
user's authority to operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that the interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003
Cet appareil numÈrique de la classe B est
conforme ‡ la norme NMB-003 du Canada
2 General Description
The SARGENT Keypad Mortise Lock/Prox is designed for areas which require authorized entry.
It is a self-contained microprocessor-controlled keypad with non volatile solid-state memory. The
keypad will hold a total of 100(LK) / 500(LU, PK, PA) different User Codes. User Codes “01”,
“02”, and “03” are utilized for Master Code, Emergency Code, and Supervisory Code,
respectively.
This product is operated by six (6) “AA” Duracell Alkaline Batteries. SARGENT mortise locks are
designed with high quality components to provide the high security, performance and durability.
Warning
To comply with “Fire Listed” doors, the batteries must be replaced with Alkaline batteries only.
3 Specifications
• Latchbolt - Stainless Steel
• Deadbolt - Stainless Steel
• Outside lever controlled by Keypad,
Keypad/Prox or Prox only
• Handed - Easily field reversible without
disassembling the lock body
• Inside lever retracts latchbolt and deadbolt
• Locks furnished for 1 3/4" doors. Can be
furnished for other door sizes upon request.
Consult factory
• Case - 12 gauge heavy duty wrought steel
• U.L. Listed (3 hr.)
• Guardbolt - Stainless Steel, non handed
4 Parts Breakdown
’A’ DESIGN
(LH)
’A’ DESIGN
(RH)
’E’ DESIGN
’B’ DESIGN
’F’ DESIGN
’H’ DESIGN
’J’ DESIGN
’P’ DESIGN
’L’ DESIGN
’W’ DESIGN
12
13
13
26
30
21
17
33
24
16
22
11
26
15
24
25
20
23
31
14
16
21
15
17
22
18/19
20
11
29
27/28
Parts Breakdown (Continued)
Item #
Part#
Description
82-3846
82-3847
82-3848
82-3849
82-0493
82-0495
82-3837
82-3838
82-3839
82-3840
82-3841
82-3842
82-0492
82-0494
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
52-2437
01-1212
01-0297
82-0507
77-0772
01-0844
01-0543
77-0168
52-0033
01-1500
82-3088
01-1495
82-0368
82-0347
82-0081
82-0084
01-1028
01-2299
01-1019
82-0184
01-0079
82-3082
81-0723
01-1472
01-1174
81-0467
81-0468
81-0490
81-0470
81-0471
81-0447
81-0489
81-0513
81-0445
Outside Escutcheon with Cylinder Hole and Key Pad, or Key Pad / Prox
Outside Escutcheon without Cylinder Hole and Key Pad or Key Pad / Prox
Outside Escutcheon with Cylinder Hole and Prox Only
Outside Escutcheon without Cylinder Hole and Prox Only
Outside Escutcheon Housing Only with Cylinder Hole
Outside Escutcheon Housing Only without Cylinder Hole
52-2431 Proximity Circuit Board and Harness Assembly
52-2432 Key Pad / Proximity Circuit Board and Harness Assembly
Inside Escutcheon with Thumb Turn and 100 User Controller
Inside Escutcheon without Thumb Turn and 100 User Controller
Inside Escutcheon with Thumb Turn and 500 User Controller
Inside Escutcheon without Thumb Turn and 500 User Controller
Inside Escutcheon with Thumb Turn Prox / Key Pad Controller
Inside Escutcheon without Thumb Turn Prox / Key Pad Cont.
Inside Escutcheon Housing Only without Thumb Turn
Inside Escutcheon Housing Only with Thumb Turn
52-2440 100 (LK) User Key Pad Controller Assembly
52-2447 500 (LU, PK) User Key Pad Controller Assembly
52-2454 Key Pad / Proximity (PK), Proximity Only (PA) Controller Assembly
Battery Cover Assembly
Security Screw
Security Tool
Thumb Turn
Spindle (Thumb Turn)
Washer (Thumb Turn)
Spring Grip Fastener (Thumb Turn)
Thru Bolts #8-32 x 1 7/8” Flat Head Screw
Fire Stop Plate
Fire Stop Screws #8 x 1/2” Type “AB” Phillips Pan Head Self Tap
Inside Spindle Adapter & Plate Assembly
Screw #8-32 x 1/2”
Inside Spindle / Outside Spindle
Inside Spring / Outside Spring
Face Plate no Dead Bolt
Face Plate with Dead Bolt
Face Plate Screws Machine 8-32 x 1/4”
Lock Body Screws / Wood Door #12 x 1 1/4”
Lock Body Screws / Metal Door 12-24 x 1/2”
Cap Nut
Washer
Plate Assembly
Post
Lever Handle Screw, A, E & F Lever
Lever Handle Screw, B, J, L, P & W Lever
Inside Lever (L.H.) "A" Design
Inside Lever (R.H.) "A" Design
Inside Lever "B" Design
Inside Lever "E" Design
Inside Lever "F" Design
Inside Lever "J" Design
Inside Lever "L" Design
Inside Lever "P" Design
Inside Lever "W" Design
# Required
Parts Breakdown (Continued)
Item #
30
31
32
33
Part#
Description
82-0151
82-3074
82-0152
82-3073
82-0153
82-0154
82-3074
82-0155
82-3076
82-3079
82-0156
82-0157
82-0158
82-0159
82-3732
82-3733
01-0803
52-0253
O/S Lever Handle R.H. "A" Design
O/S Lever Handle R.H. "A" Design Stainless Steel
O/S Lever Handle L.H. "A" Design
O/S Lever Handle L.H. "A" Design Stainless Steel
O/S Lever Handle "B" Design
O/S Lever Handle "E" Design
O/S Lever Handle "E" Design Stainless Steel
O/S Lever Handle "F" Design
O/S Lever Handle "F" Design Stainless Steel
O/S Lever Handle "H" Design
O/S Lever Handle "J" Design
O/S Lever Handle "L" Design
O/S Lever Handle "P" Design
O/S Lever Handle "W" Design
Lockbody Assembly (with deadbolt) (8276 & 8277)
Lockbody Assembly (without deadbolt) (8278 & 8279)
Battery Alkaline ("AA" cell)
Battery Keeper
# Required
5 Features
• Non volatile memory
• Cylinder override optional
• Motor driven, battery operated mortise lock
• Entry of three wrong User Codes disables
all codes for ten seconds. Yellow LED
on solid
• Battery operated with 6 each “AA” Alkaline
• Low battery alert–4 chirps after code entry
• External remote “request to exit” connector
• Piezo horn can be heard with each keystroke
or turned off by Master or Supervisory Code
• Supervisory code will unlock door when low
battery had expired
• Last 15 (LK) transactions can be output to
portable printer via infrared link
• 100 (LK) or 500 (LU, PK, PA) users total
• Last 1000 (LU, PK, PA) transactions can be
output to portable printer via infrared link or
PC via Soflink™ Plus software
• Programming done at keypad or with
Soflink™ Plus software and a PC
(LU, PA, PK). Soflink™ Plus Software User
Manual A7462
• Proximity FOB or Card optional
• Deadbolt switch inside mortise lock allows
Emergency Code and Master Code holders
to gain entry when deadbolt is thrown
• Operates utilizing any two to six digits per
code. Digits may be repeated and codes may
start with zero
6 Installation Instructions
• Verify hand and bevel of door
Right Hand
Hinges Right
Open Inward.
"RH"
Left Hand
Reverse Bevel
Hinges Left.
Open Outward
"LHRB"
Left Hand
Hinges Left.
Open inward.
"LH"
Right Hand
Reverse Bevel
Hinges Right.
Open Outward.
"RHRB"
Lock Body
Latchbolt
Right Hand
Left Hand
Reverse Bevel
Bevel
Right Hand
Reverse Bevel
• View lock body from top and from
the outside (as shown above)
Top
Connector and Wires
Front
Deadbolt
Latchbolt
Lock w/cylinder
Override
(Shown)
End Cap
Guardbolt
Installation Instructions (Continued)
Door Preparation
Thrubolt hole
Hole for ribbon
cable from
controller to
keypad
Outside of
Door
Inside of
Door
Inside
Cylinder
Hole
Thumb Turn
Lever Hole
Outside
Cylinder Hole
Mortised
area
Lever
Handle Hole
Lever Handle Hole
Thrubolt hole
Pre-drilled and /or
Tapped Holes 2 places
NOTE: Always consult the proper template prior to drilling any holes.
Installation Instructions (Continued)
How to Reverse Lock Hand
If it is necessary to change hand of locking piece :
1. Turn lockbody to side NOT marked with
RED locking piece.
Connector
2. Insert blade of common screwdriver into locking piece slot.
3. Push locking piece toward front of
lockbody and rotate until RED shows.
4. RED indicates locked (outside) side.
5. Wire harness
MUST exit thru non-cylinder side.
End Cap
Locking
RED color
guide slot
locking piece
Push in
indicates locked side
Right Hand
Shown
If it is necessary to change hand Latchbolt :
1. Insert blade of common screwdriver into oval slot behind latchbolt.
2. Push latchbolt out until back of bolt
clears lockbody front.
3. Rotate latchbolt 180¡ until the latchbolt
drops back into the lockbody.
End Cap
Oval slot
Push
out
Push
out
Rotate
Latchbolt
Outside of
Door
Installation Instructions (Continued)
Step #1 Installation of Lockbody/Attaching Lockbody Screws
• Wires and Connector go into the mortised
area and out of the inside cylinder hole
Inside of
Door
MUST feed
Connector
& Wires thru
non-cylinder
side.
(2) #12-24 x 1/2" long
Flat Head Screw
for metal doors
(2) #12 x 1 1/4" long
Flat Head Wood Screw
for wood doors
• Insert Lockbody in mortised cutout
• Hold loosely in place with (2) Lockbody screws
• DO NOT TIGHTEN SCREWS AT THIS TIME
Installation Instructions (Continued)
Step #2 Attaching of Fire Stop Plate
NOTE: Fire stop plate is required
on all fire rated doors
(2) 1/8" Dia holes required
CL Of 1 1/2" Dia
7"
Slot
11"
(2) Self Tapping
Screws #8 x 1/2"
long for wood
& metal doors
Outside of
Door
10
Installation Instructions (Continued)
Step #3 Installation of Outside/Inside Escutcheon & Lever Assembly
To secure the adapter and plate
assembly to the inside of the door,
thread the screws mounting posts
of the outside lever assembly.
From the outside of the door, feed wires and
connector through fire stop plate
Keypad/prox connector
and cable
Mortise lockbody
connector and wire
Tighten retaining nut by hand.
Back off retaining nut slightly
until star pattern lines up with
square lever assembly corners
Insert Spindle into square
hole on inside
of door.
With outside lever horizontal, carefully insert the mounting
posts through the door and lockbody. Make sure the spindle
is properly engaged in the lock.
NOTE: For installation of optional gasket
Part #82-0500 see Gasket Installation
Plug Keypad Connector
into inside Escutcheon
as shown. Place excessive
wire in hole.
Plug smaller Connector
as shown into the inside
Escutcheon. Place
excessive wire in inside
escutcheon assembly.
Keep excessive wires
away from cylinder hole.
NOTE:
Both connectors go on
only one way. Do not
offset the connectors.
Be sure connectors are
seated completely.
If not seated, Keypad
will not function properly.
*8-32
Flat Head
Screw
Outside of
Door
Locate (2) #8-32 Flat Head Screw and insert through the
escutcheon into the outside escutcheon. Tighten firmly.
11
Installation Instructions (Continued)
Step #4 Installation of Inside Lever/Outside Cylinder
• Align cylinder
• Put the turn lever
in the up position
• Screw cylinder
lockbody unit
Type 43 Mortise
Cylinder ONLY
Inside Lever
Key
•
Inside of
Door
Outside of Door
Set
Screw
• Slide lever handle onto spindle until fully seated.
Be sure handle is horizontal and facing to the rear of door
• Tighten the set screw securely with
1/8" hex wrench
• Tighten the set
screw to prevent
unscrewing of the
cylinder
• Turn the key way in
the cylinder to make
certain that the locking
or latching mechanism
function correclly.
Set screw
NT
SARGENT
RG
Note: Key and the
cylinder must be
rotated as shown
Very Important
SA
Phillips
screwdriver
Correct
Wrong
12

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:05:15 10:04:54-07:00
Create Date                     : 2001:05:15 10:04:36-07:00
Producer                        : Acrobat Distiller 4.0 for Macintosh
Page Count                      : 14

EXIF Metadata provided by EXIF.tools