Elpas Solutions 5-LFB00125 PROXIMITY BUS READER User Manual Proximity BUS Reader Wiring Guide

Elpas Solutions Ltd. PROXIMITY BUS READER Proximity BUS Reader Wiring Guide

User Manual

  www.elpas.com Page 1 of 6 V10/March 2014  Elpas Proximity BUS Reader P/N: 5-LFA00125 Installation Guide Introduction This installation guide provides basic instructions for common Proximity BUS Reader installation scenarios. For UL 294 Compliant Applications refer to page 4 of this document for a listing of applicable installation considerations.  CAUTION: It is important that you read, understand, and follow the instructions in this document. If you have questions, call your local Elpas support representative. All reasonable efforts have been made to ensure that the specifications and other information in this guide are accurate and complete at the time of its publication. Nonetheless, all information contained within this document is subject to change at any time without prior  notice.  Any  modifications  to  this  equipment  without  prior  written  consent  of  Elpas  Solutions  Ltd.  will  void  all  warranties  including  the pertinent regulatory certifications and as such revoke your authority to operate this product. Furthermore unauthorized modifications may also result in damage to this device and may cause a safety hazard to the users. Product Description The  Elpas  Proximity  BUS  Reader  is  a  125KHz,  EM4100 compatible;  indoor/outdoor  surface  mounted  proximity  reader. The reader features low power consumption, high reliability, and consistent read ranges (up to 10cm /4 inches), regardless of card or tag. Designed  for  indoor/outdoor  environments,  the  reader’s  solid state electronics  is housed in an  epoxy potted, (IP-67 rated), of thermoplastic  casing  that  ensures  years  of  maintenance  free deployments. The Proximity BUS Reader contains an onboard I/O that enables the  monitoring  of  one  alarm  sensor  and  control  of  one  digital open-collector  output.  The  proximity  reader  also  includes  a 2m/6.5ft long RS-485 power/data cable for interfacing to a Elpas BUS Master (a RF IP Reader or an ELC Controller) via a RS-485 Junction Box (P/N:5-JBA00485). Note: An Elpas RS-485 BUS may contain up to fifteen Elpas BUS devices (such as RF or IR Readers, Elpas Display Panels, LF Beacons, or other Proximity  BUS  Readers)  which  are  wired  together  using  Elpas  RS-485 Junction Boxes. \            LF Proximity BUS Reader - Network Topology   Mounting Considerations The Proximity BUS Reader should be wall mounted, adjacent to the opening side of the door (outside of the protected area), at a height of approximately 1.2m/4ft above the floor Note:  When  installing  Proximity  BUS  Readers  on  adjacent  doors, make certain that the minimum distance between readers is at least 60cm/2.0ft to ensure proper operation. Mounting Procedure 1. Insert a screwdriver into the recess at the bottom of the case, and separate the cover from the reader. 2. Place the base on the installation surface, mark two screw holes, drill  the  holes,  and  insert  the  supplied  plastic  anchors,  if necessary. 3. Fasten the  base to the mounting surface, using  the two #6 Tap screws supplied with the reader. 4. Replace the reader’s cover, ensuring that the cover is aligned with the reader. This enables the LED to be visible.        Note: Do not install the Proximity BUS Reader directly onto a metal surface, since can significantly decrease the effective read range of the device. If you have to mount the reader onto a metal surface, insert  a  RDR-BACK  (P/N:  3-6317-0)  between  the  device’s  reader base and the metal surface.
Proximity BUS Reader – Installation Guide    www.elpas.com Page 2 of 6 V10/March 2014   LED Status Indicator The Proximity BUS Reader contains a tri-colored (Red, Green and Orange) software configurable LED array that can be used to specify the status of the device. Refer to the Eiris Software (V4.7.1 or higher) or the ELC Programmer Software (V2.1 or higher) Configuration Guides for setup details. By default, the Red LED is used to indicate the following device trouble conditions: o  The reader is unregistered (flashes once/sec.) o  The reader has lost RS-485 communication (flashes once/sec.)  RS-485 Interface The  Proximity  BUS  Reader  has one 2m/6.5ft,  6-wire  AWG-26 power/data cable with a male RJ-11 connector (6P6C) for connecting to the RS-485 Junction Box. I/O Interface The  Proximity  BUS  Reader  also  has  a  2m/6.5ft,  4-wire  AWG-22 cable with ends for connecting two inputs and one digital output. Color Conductor Details Black Ground Red  Digital Output Green Input 1 (IN1) White Input 2 (IN2) IMPORTANT:  BUS  Beacons  MUST  BE  powered-down  while  wiring  the  unit’s I/Os  and  when  connecting  to  the  RS-485  BUS.  This  will  prevent  accidental shorts/spikes to cause damage to the devices.  General Purpose Inputs The  Proximity  BUS  Reader  has  two  general  purpose  analog (N.O.) dry contact inputs for monitoring alert sensors or emergency call buttons designated IN1 and IN2.  EOL supervision may be added to either of these inputs to detect: Open, Close, Line Cut and Line Short conditions using an End-of-Line Terminator (P/N: 5-IOX00001). Note: Elpas End-of-Line Terminators have not been evaluated for use in UL Applications.  Recommended Cable: 22 AWG, unshielded/twisted pair.  Digital Output The  Proximity  BUS  Reader  has  one  dry  contact  open-collector digital  output  (up  to  100mA,  28VDC)  for  actuating  an  alert response device.  Note: The output is resistive loading only, there is no power factor. Recommended Cable: 22 AWG, unshielded/twisted pair.
Proximity BUS Reader – Installation Guide    www.elpas.com Page 3 of 6 V10/March 2014  RS-485 BUS/Stub Topology The RS-485  BUS MUST BE  wired using a  BUS/Stub  topology where the BUS  Master  (a  RF  IP Reader or an ELC Controller) is connected anywhere along the BUS. The topology supports data transmission between the BUS Master and up to 15 Elpas BUS Devices (such as RF or IR Readers; LF Beacons primary & secondary), Elpas Display Panels and 6x6 I/O Modules using Elpas RS-485 Junction Boxes (P/N: 5-JBA00485). IMPORTANT NOTE: Only 1 RF IP Reader/ELC Controller and up to 7 RF BUS Readers may coexist together on a single BUS. 200M/650Ft: Max. BUS length      10M/30Ft: Max. Stub length       100 Ohm Termination: Required each end of the BUS.   Recommended Cable/Power Supply Types: BUS Backbone:  CAT5 solid (4x2x26AWG). Power: Three twisted pairs  (six conductors) between junction boxes. Data: One twisted pair (two conductors) between junction boxes. Power: 16 to 28 VDC/2.5A Limited. Note: For UL installations use only UL 294 (ALVY) compliant power supplies (see page 4 for details).
Proximity BUS Reader – Installation Guide    www.elpas.com Page 4 of 6 V10/March 2014  Electrical Specifications Frequency Low frequency electromagnetic field (125 KHz) ISO Card Standard EM 4100 *Read Range Up to 10 cm/4.0 inches  (actual range depends on the proximity card or tag) RS-485 BUS 230Kbit/sec Device Supervision Lost Away, Low Voltage, RS-485 BUS Communication Problem Red LED Indicator Unregistered in Eiris/ELC Programmer - Flashes once/second Power up/RS-485 Communication Loss - Flashes once/second Status LED  Software configurable Inputs/Output Two dry contact analog inputs (N.O.)     One dry contact open collector digital output (up to 100mA) Input Supervision 4 Levels (Open, Closed, Line Short, Line Cut) using optional Elpas End-of-Line Terminator (Elpas End Of Line Terminators have not been evaluated for use in UL Applications) Power Requirements 12–28VDC, 48mA @ 24VDC General Specifications Construction White polycarbonate plastic (IP-67) Device Interfaces RS-485 Bus & Power: 2 meter/6.5ft in length, 6-wire AWG 26 cable with male RJ-11 (6P6C) connector Input/Output : 2 meter 2 meter/6.5ft in length, 4-wire AWG 22 cable with ends Dimensions (H x W x D) 116 x 70 x 16.8mm…(4.5 x 2.76 x 1.62 inches) Weight 121.5 grams (4.3 ounces) Operating Environment Temp: -20°C to 50°C (-4°F to 122°F)…...Humidity: 20% to 100% non-condensing Minimum Distance Between Readers 30cm/ 12 inches Management software Eiris 4.7.1 (or higher) Software *Actual read range depends on card/tag type, electrical environment and proximity to metal.                     Specifications are subject to change without notice.     Selected Compatible Accessories Part Number Description 3-6302-2 White proximity reader replacement cover (8 units) 3-6317-0 RDR-BACK, mounting spacer for metal surfaces 5-IOX00001 End-of-Line Terminator for Elpas & AXS Inputs (5 units) 5-JBA00485 RS-485 Junction Box, 4 RJ11 Ports 5-ERS02800 P60 Power Supply, 24VDC/2.2A
Proximity BUS Reader – Installation Guide    www.elpas.com Page 5 of 6 V10/March 2014    UL 294 Compliance Installations For all Elpas UL 294 compliant installations, the following requirements must be met:   UL installations are Controller based only and do not include an Eiris Server.   Elpas Fixed Infrastructure Products (except for Outdoor RF Readers) can only be installed in interior building locations only that do not exceed the following environmental conditions:  o Temp: 0°C to 49°C (32°F to 120°F) o Humidity: 85% non-condensing   Only 24VDC, UL 294 (ALVY) compliant power supplies such as Altronix  model AL600ULPD4 can be used to power Elpas Infrastructure Products Note: All circuits must be power limited.   Elpas Outdoor RF Readers (Elpas PNs: 5-RFB00433-6 and 5-ELC00433-4) can only be installed in exterior building locations that do not exceed the following environmental conditions:  o Temp: -35°C to 66°C (-31°F to 151°F)  o Humidity: 20% to 95% non-condensing   Only UL 294 compliant products may be connected to the outputs of any Elpas infrastructure device and may not be used for ”Burglary Applications”. Limitations Elpas Healthcare applications which are designed for hospitals assisted living and nursing care facilities for the protection of staff personnel, patients or residents are not UL 294 compliant. Specific Conditions    Elpas End-of-the Line Terminators (Elpas P/N: 5-IOX00001) are not evaluated for use in UL 294 Compliant Installations by Underwriters Laboratories. Therefore, supervised inputs are for non UL applications only.   High-Power LF Beacons need to be powered locally and should not share the same power supply with any other Elpas Fixed Infrastructure Product. Note: Applies to the following Elpas P/Ns: 5-RLF00001-3, 5-RLF00001-31 and 5-RLF00001-32.   To ensure RF detection reliability the read range installation grids for all Local Controllers and RF Readers  need to be designed so that received  messages from the Active RFID Tag does not fall below a RSSI Value  of 121 (-90dBm). Note: Applies to the following Elpas P/Ns: 5-RFB00433, 5-RFB00433-1, 5-RFB10433-2, 5-RFB10433-5,5-RFB00433-6, 5-ELC00433-1, 5-ELC10433-2,  5-ELC10433-3 and 5-ELC00433-4.
Proximity BUS Reader – Installation Guide   Page 6 of 6 V10/March 2014  W.E.E.E. Product Recycling Declaration For  information regarding the recycling  of this product  you must contact the  company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier.  This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment.    Regulatory EU Declaration of Conformity This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. FCC & IC Compliance StandardsThis device (FCC #:04X5-LFA00125 and IC #:1467G-5LFA00125) complies with FCC Rules Part 15 and with industry Canada license exempt RSS. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)  This  device  must  accept  any  interference  received,  or  that  may  cause undesired operation. For  industry  Canada:  Le  présent  appareil  est  conforme  aux  CNR  d'Industrie Canada  applicables  aux  appareils  radio  exempts  de  licence.  L'exploitation  est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,  et  (2)  l'utilisateur  de  l'appareil  doit  accepter  tout  brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Note: This equipment has been tested and found to comply with the limits for a Class B  digital  device, pursuant to part 15 of the FCC Rules.  These limits are designed  to  provide  reasonable  protection  against  harmful  interface  in  a residential  installation.  This  equipment  generates;  uses  and  can  radiate  radio frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the instructions, may cause harmful interference to radio communications. However, there is  no guarantee that interference will not occur in a particular installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:    Reorient or relocate the receiving antenna.   Increase the separation between the equipment and receiver.   Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to which the receiver is connected.   Consult the dealer or an experienced radio/TV technician for help.  Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Elpas Solutions Ltd.) could void the user’s authority to operate the equipment. Company Contact Elpas, Inc. Westford, Massachusetts (USA) -Tel: 1-800-223-0020 . Product Warranty Elpas  Solutions,  Ltd.  (the  Company),  and  its  affiliates,  warrants  its  products (hereinafter  referred  to  as  "the  Product”)  to  be  free  of  defects  in  materials  and workmanship under  normal  operating  conditions and  use for  a  period  of one year from  the  date  of  shipment  by  Elpas.  The  Company’s  obligations  shall  be  limited within the warranty period, at its option, to repair or to replace the defective Product or any defective  component or part thereof. To  exercise this warranty, the product must be returned to the manufacturer freight prepaid and insured. This  warranty  does  not  apply  to  repairs  or  replacement  caused  by  improper installation,  Product  misuse,  failure  to  follow  installation  or  operating  instructions, alteration, abuse, accident, tampering, repair by anyone other than Elpas, external causes, and failure to perform required preventive maintenance. This warranty also does not apply to any products, accessories, or attachments used in conjunction with the  Product,  including  batteries,  which  shall  be  covered  solely  by  their  own warranties,  if  any.  Elpas  shall  not  be  liable  for  any  damage  or  loss  whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, resulting from a malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in conjunction with the Product. ELPAS MAKES NO EXPRESS WARRANTIES EXCEPT THOSE STATED IN THIS STATEMENT.  ELPAS  DISCLAIMS  ALL  OTHER  WARRANTIES,  EXPRESS  OR IMPLIED,  INCLUDING  WITHOUT  LIMITATION  IMPLIED  WARRANTIES  OF MERCHANTABILITY  AND  FITNESS  FOR  A  PARTICULAR  PURPOSE.  ELPAS’S SOLE RESPONSIBILITY FOR WARRANTY CLAIMS IS LIMITED TO REPAIR OR TO REPLACE AS SET FORTH IN THIS STATEMENT. Elpas shall have no liability for any death, personal injury, property damage, or other loss  whether  direct,  indirect,  incidental,  consequential,  or  otherwise,  based  on  a claim  that the  Product failed  to function. However, if Elpas is  held liable, whether directly  or  indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless  of cause or  origin, the company's maximum liability shall be limited  to  the  purchase  price  of  the  Product,  which  shall  be  fixed  as  liquidated damages and not as a penalty, and shall be the complete and exclusive liability of Elpas. Elpas shall not, under any circumstances whatsoever, be liable for any inaccuracy, error of judgment, default, or negligence of Elpas, its employees, officers, agents, or any  other  party,  or  of  the  purchaser  or  user,  arising  from  any  assistance  or communication  of  any  kind  regarding  the  configuration,  design,  installation,  or creation of security system involving the Product, that being the responsibility of the purchaser  or  user.  If  Elpas  is  unable  to  make  such  repair  or  replacement,  the company’s  entire  liability  shall  be  limited  to  the  cost  of  a  reasonable  substitute product.  Elpas  shall  not  be  responsible  for  any  dismantling,  installation, reinstallation, purchasing, shipping, insurance, or any similar charges.  Elpas shall have no liability for any damages, including without limitation, any direct, indirect, incidental, special, or consequential damages, expenses, costs, profits, lost savings or earnings, or other damages arising out of the use of the Product or the removal,  installation,  reinstallation,  repair  or  replacement  of  the  Product  or  any related events. In the event that there is any liability against Elpas, such liability shall be  limited  to  the  purchase  price  of  the  Product  which  amount  shall  be  fixed  as liquidated damages. The  purchaser  and  user  understand  that  this  Product  may  be  compromised  or circumvented by intentional acts; that the Product will not in all cases prevent death, personal injury, property damage, or other loss resulting from burglary, robbery, fire or other causes; and that the Product will not in all cases provide adequate warning or protection. The purchaser and user also understand that a properly installed and maintained alarm may reduce the risk of events such as burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such events will not occur or that there will be no death, personal injury, property damage, or other loss as a result of such events. By purchasing the Product, the purchaser and user shall defend, indemnify and hold Elpas, its officers, directors, affiliates, subsidiaries, agents, servants, employees, and authorized  representatives  harmless  from  and  against  any  and  all  claims,  suits, costs, damages,  and judgments incurred, claimed,  or  sustained whether for death, personal injury, property damage, or otherwise, because of or in any way related to the configuration, design, installation, or creation of a security system involving the Product,  and  the  use,  sale,  distribution,  and  installation  of  the  Product,  including payment of any and  all attorney’s fees, costs, and expenses incurred as a result of any such events. The  purchaser  or  user  should  follow  the  Product  installation  and  operation instructions and test the Product and the entire system at least once each week. For various  reasons,  including  but  not  limited  to  changes in  environmental  conditions, electric,  electronic, or electromagnetic disruptions, and tampering, the Product may not perform as expected. The purchaser and user are advised to take all necessary precautions for the protection and safety of persons and property. This  statement  provides  certain  legal  rights.  Other  rights  may  vary  by  state  or country.  Under  certain  circumstances,  some  states  or  countries  may  not  allow exclusion or limitation of incidental or consequential damages or implied warranties, so  the  above  exclusions  may  not  apply  under  those  circumstances  and  in  those states or countries. Elpas  reserves the right to  modify this  statement at any time, in its sole discretion without  notice  to  any  purchaser  or  user.  However,  this  statement  shall  not  be modified  or  varied  except  by  Elpas  in  writing,  and  Elpas  does  not  authorize  any single individual to act on its behalf to modify or vary this statement. Any questions about this statement should be directed to Elpas.

Navigation menu