Elpas Solutions 5-RRB00880 ELPAS IR READER RS-485 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1163220
Application ID	R5wIlCWZ2jAc3uqZlZf72w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.27kB (353428 bits)
Date Submitted	2009-09-02 00:00:00
Date Available	2009-09-04 00:00:00
Creation Date	2009-08-27 10:38:03
Producing Software	Acrobat Distiller 8.0.0 (Windows)
Document Lastmod	2009-08-27 11:11:16
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 8.0 for Word
Document Author:	David F

Elpas
Gen-2 IR Location Reader
Wiring Guide - For P/N: 5-IRB00880
Active RFID/RTLS Solutions
Introduction
This wiring guide provides basic instructions for common installation scenarios. For advanced functionality, this document should
also be used in conjunction with the Elpas Gen-2 IR Reader Installation & Configuration Guide.
Download from the EIRIS Software Download Page (http://www.visonictech.com/Eiris.html) of the VT Website the Elpas 4.6.3
Installer file, which contains all the necessary software extensions and updates for enrolling and configuring Gen-2 IR Location
Readers into existing or new EIRIS installations. It is highly recommended that you ensure that the EIRIS installation on the host
machine has been properly updated before wiring the readers.
Note: VT is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
Product Description
The Gen-2 IR Location Reader is a
supervised; fixed receiving device that detects
and relays ‘State’ and sub-room ‘Location’
data from Elpas Active RFID IR-enabled tags
to host applications over wired or wireless
Ethernet/Wi-Fi networks in real-time.
The reader’s onboard I/O enables the local
monitoring of one general purpose analogue
input and control of one open-collector digital
switched device. The reader also supports
RS-485 data transmission to fourteen other
Elpas RS-485 BUS devices plus to one Elpas
RF Ethernet Reader.
FCC Compliance: PART 15, Sub-part B, Class B FCC ID: O4X5-IRB0088
CE Compliance: EN300220-1, EN300220-2, EN60950-1, ICES-003, CAN/CSA-CEI/ICE CISPR 22
IC Compliance: 1467G IRB00880
Circuit Board Terminal Blocks
Power
The Gen-2 IR Location Reader has one analogue input (J2) and
one digital open-collector output (J1) located on the right-hand
side of the board. The reader also includes a four position colorcoded removable RS-485 terminal block (J3) for date and power
connections (see page 2 for details).
Ensure that the Gen-2 IR Location Reader is connected to the
power source. Then switch off the device till you have wired the
I/O and the RS-485 BUS terminal blocks to prevent accidental
shorts or power spikes from causing damage to the reader.
Power Requirements: 100mA/24Vdc
Recommended Cable: CAT5 Stranded (4x2x26AWG)
Max Distance: Refer to wiring topologies on page 2
Analogue Input
The Gen-IR Location Reader is equipped with one general
purpose analogue input (Terminal Block J2). The input is a
two-wired supervised circuit for monitoring alarm detection
devices such as ultrasonic motion detectors and door contacts.
Recommended Cable: 22 AWG, unshielded/twisted pair
Digital Outputs
The Gen-IR Location Reader has a general purpose digital
output (Terminal Block J1) that provides open-collector
switching (up to 100mA, 28Vdc).
The Gen-2 IR Location Reader has a Service Pin/Tamper
Switch that generates service messages when pressed to aide
device registration. The Service Pin/Tamper Switch is also used
to indicate attempts to remove the device’s cover after the
device has been enrolled in EIRIS.
Page 1 of 2
D-302086_V5/Aug. 09
Recommended Cable: 22 AWG, unshielded/twisted pair
Elpas Gen-2 IR Location Reader – Wiring Guide
RS-485 BUS/Stub Topology
The Elpas-2 RS-485 BUS may be wired using a BUS/Stub topology using 4-port EJB boxes (P/N: 5-EJB00001). This topology
supports data transmission between 1 RF Ethernet Reader (BUS-Master) and up to 15 BUS Slaves (IR Readers, I/Os,
RDUs…etc). Additionally the reader may be connected at any location along the RS-485 data BUS.
200M/650Ft: Max. BUS length
10M/30Ft: Max. Stub length
100 Ohm Termination: Required each end of the BUS
Recommended Cable Type: CAT5 Stranded (4x2x26AWG)
For Power: Use three twisted pairs (six conductors) between EJBs
For Data: Use one-twisted pair (two conductors)
Use one twisted pair (two conductors) between each EJB and Reader.
RS-485 Daisy Chain Topology
The Elpas-2 RS-485 BUS may be wired using a Daisy Chain topology. This configuration supports data transmission between
1 RF Ethernet Reader (BUS-Master) and up to 7 BUS Slaves (IR Readers, I/Os, RDUs...etc).
The RF Ethernet Reader may be connected at any location on the RS-485 data chain as long as the power supply is connected
to the power BUS in close proximity to the RF reader.
100M/325 Ft: Maximum cable length
100 Ohm Termination: Required at each end of the daisy chain
Recommended Cable Type: CAT5 Stranded (4x2x26AWG)
For Power: Use one twisted pair (two conductors)
Page 2 of 27
D-302086_V5/Aug. 09
For Data: Use one-twisted pair (two conductors)
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it.
If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier.
This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Company                         :  Visonic Ltd.
Source Modified                 : D:20090827073733
Create Date                     : 2009:08:27 10:38:03+03:00
Creator Tool                    : Acrobat PDFMaker 8.0 for Word
Modify Date                     : 2009:08:27 11:11:16-04:00
Metadata Date                   : 2009:08:27 11:11:16-04:00
Document ID                     : uuid:4180d95a-4d79-465d-8cee-9dcce67d6be7
Instance ID                     : uuid:07ba5c4f-b347-4636-9285-a3a666404881
Subject                         : 5
Format                          : application/pdf
Creator                         : David F
Title                           : 
Page Count                      : 2
Page Layout                     : OneColumn
Author                          : David F

EXIF Metadata provided by EXIF.tools