Emerson Process Management Micro Motion 1500 Users Manual Transmitters With The Filling And Dosing Application

2015-02-06

• Contents
• Before You Begin
  • 1.1 Overview
  • 1.2 Safety
  • 1.3 Version
  • 1.4 Flowmeter documentation
  • 1.5 Communication tools
  • 1.6 Planning the configuration
  • 1.7 Pre-configuration worksheet
  • 1.8 Micro Motion customer service
• Connecting with ProLink II Software
  • 2.1 Overview
  • 2.2 Requirements
  • 2.3 ProLink II configuration upload/download
  • 2.4 Connecting from a PC to a Model 1500 transmitter
• Flowmeter Startup
  • 3.1 Overview
  • 3.2 Applying power
  • 3.3 Performing a loop test
  • 3.4 Trimming the milliamp output
  • 3.5 Zeroing the flowmeter
    • 3.5.1 Preparing for zero
    • 3.5.2 Zero procedure
• Required Transmitter Configuration
  • 4.1 Overview
  • 4.2 Characterizing the flowmeter
    • 4.2.1 When to characterize
    • 4.2.2 Characterization parameters
    • 4.2.3 How to characterize
  • 4.3 Configuring the channels
  • 4.4 Configuring the measurement units
    • 4.4.1 Mass flow units
    • 4.4.2 Volume flow units
    • 4.4.3 Density units
    • 4.4.4 Temperature units
    • 4.4.5 Pressure units
  • 4.5 Configuring the mA output
    • 4.5.1 Configuring the primary variable
    • 4.5.2 Configuring the mA output range (LRV and URV)
    • 4.5.3 Configuring the AO cutoff
    • 4.5.4 Configuring the fault action, fault value, and last measured value timeout
    • 4.5.5 Configuring added damping
  • 4.6 Configuring the discrete output(s)
  • 4.7 Configuring the discrete input
  • 4.8 Establishing a meter verification baseline
• Using the Transmitter
  • 5.1 Overview
  • 5.2 Recording process variables
  • 5.3 Viewing process variables
  • 5.4 Viewing transmitter status and alarms
    • 5.4.1 Using the status LED
    • 5.4.2 Using ProLink II software
  • 5.5 Using the totalizers and inventories
• Optional Transmitter Configuration
  • 6.1 Overview
  • 6.2 Default values
  • 6.3 Parameter location within ProLink II
  • 6.4 Creating special measurement units
    • 6.4.1 About special measurement units
    • 6.4.2 Special mass flow unit
    • 6.4.3 Special volume flow unit
    • 6.4.4 Special unit for gas
  • 6.5 Configuring cutoffs
    • 6.5.1 Cutoffs and volume flow
    • 6.5.2 Interaction with the AO cutoff
  • 6.6 Configuring the damping values
    • 6.6.1 Damping and volume measurement
    • 6.6.2 Interaction with the added damping parameter
    • 6.6.3 Interaction with the update rate
  • 6.7 Configuring the update rate
    • 6.7.1 Effects of Special mode
  • 6.8 Configuring the flow direction parameter
  • 6.9 Configuring events
  • 6.10 Configuring slug flow limits and duration
  • 6.11 Configuring fault handling
    • 6.11.1 Changing status alarm severity
    • 6.11.2 Changing the fault timeout
  • 6.12 Configuring digital communications
    • 6.12.1 Changing the digital communications fault indicator
    • 6.12.2 Changing the Modbus address
    • 6.12.3 Changing the RS-485 parameters
    • 6.12.4 Changing the floating-point byte order
    • 6.12.5 Changing the additional communications response delay
  • 6.13 Configuring variable mapping
  • 6.14 Configuring device settings
  • 6.15 Configuring sensor parameters
• Configuring the Filling and Dosing Application
  • 7.1 About this chapter
  • 7.2 User interface requirements
  • 7.3 About the filling and dosing application
    • 7.3.1 Purge
    • 7.3.2 Cleaning
  • 7.4 Configuring the filling and dosing application
    • 7.4.1 Flow source
    • 7.4.2 Filling control options
    • 7.4.3 Valve control parameters
  • 7.5 Overshoot compensation
    • 7.5.1 Configuring overshoot compensation
    • 7.5.2 Standard AOC calibration
    • 7.5.3 Rolling AOC calibration
• Using the Filling and Dosing Application
  • 8.1 About this chapter
  • 8.2 User interface requirements
  • 8.3 Operating the filling and dosing application from ProLink II
    • 8.3.1 Using the Run Filler window
    • 8.3.2 Using a discrete input
    • 8.3.3 Fill sequences with PAUSE and RESUME
• Pressure Compensation
  • 9.1 Overview
  • 9.2 Pressure compensation
    • 9.2.1 Options
    • 9.2.2 Pressure correction factors
    • 9.2.3 Pressure measurement unit
  • 9.3 Configuration
• Measurement Performance
  • 10.1 Overview
  • 10.2 Meter validation, meter verification, and calibration
    • 10.2.1 Meter verification
    • 10.2.2 Meter validation and meter factors
    • 10.2.3 Calibration
    • 10.2.4 Comparison and recommendations
  • 10.3 Performing meter verification
    • 10.3.1 Specification uncertainty limit and test results
    • 10.3.2 Additional ProLink II tools for meter verification
  • 10.4 Performing meter validation
  • 10.5 Performing density calibration
    • 10.5.1 Preparing for density calibration
    • 10.5.2 Density calibration procedures
  • 10.6 Performing temperature calibration
• Troubleshooting
  • 11.1 Overview
  • 11.2 Guide to troubleshooting topics
  • 11.3 Micro Motion customer service
  • 11.4 Transmitter does not operate
  • 11.5 Transmitter does not communicate
  • 11.6 Zero or calibration failure
  • 11.7 Fault conditions
  • 11.8 I/O problems
  • 11.9 Transmitter status LED
  • 11.10 Status alarms
  • 11.11 Checking process variables
  • 11.12 Meter fingerprinting
  • 11.13 Troubleshooting filling problems
  • 11.14 Diagnosing wiring problems
    • 11.14.1 Checking the power supply wiring
    • 11.14.2 Checking the sensor-to-transmitter wiring
    • 11.14.3 Checking grounding
    • 11.14.4 Checking for RF interference
  • 11.15 Checking ProLink II
  • 11.16 Checking the output wiring and receiving device
  • 11.17 Checking slug flow
  • 11.18 Checking output saturation
  • 11.19 Checking the flow measurement unit
  • 11.20 Checking the upper and lower range values
  • 11.21 Checking the characterization
  • 11.22 Checking the calibration
  • 11.23 Checking the test points
    • 11.23.1 Obtaining the test points
    • 11.23.2 Evaluating the test points
    • 11.23.3 Excessive drive gain
    • 11.23.4 Erratic drive gain
    • 11.23.5 Low pickoff voltage
  • 11.24 Checking the core processor
    • 11.24.1 Checking the core processor LED
    • 11.24.2 Core processor resistance test
  • 11.25 Checking sensor coils and RTD
    • 11.25.1 Remote core processor with remote transmitter installation
    • 11.25.2 4-wire remote installation
• Default Values and Ranges
  • A.1 Overview
  • A.2 Default values and ranges
• Installation Architectures and Components
  • B.1 Overview
  • B.2 Installation diagrams
  • B.3 Component diagrams
  • B.4 Wiring and terminal diagrams
• Menu Flowcharts
  • C.1 Overview
  • C.2 Version information
  • C.3 Flowcharts
• NE53 History
  • D.1 Overview
  • D.2 Software change history
• Index