Emerson Asco 300 Series Commercial Power Control System Brochures And Data Sheets
2015-03-30
: Emerson Emerson-Asco-300-Series-Commercial-Power-Control-System-Brochures-And-Data-Sheets-680382 emerson-asco-300-series-commercial-power-control-system-brochures-and-data-sheets-680382 emerson pdf
Open the PDF directly: View PDF .
Page Count: 14
Download | |
Open PDF In Browser | View PDF |
For commercial, Healthcare, dataCenters and industrial facilities...wherever control of on site generators is needed The ASCO Series 346 Digital Power Control System is a standardized generator paralleling system offering the sophisticated functionality normally found in custom designs. • Reliably starts, synchronizes, parallels, monitors and protects engine generator sets for prime power and emergency power applications. • Smoothly integrates engine-generator sets and power transfer switches. • Automatic load management control. One priority block per generator, each handling up to eight loads per priority block, up to four generators. • Provides full, self-contained configurability. No need for a laptop. • Includes communication ports that provide internet and intranet access to system status and functions. • Easy to install, set up, commission, operate and service. 1 Series 346 Digital Power Control System The ASCO Series 346 Power Control System offers wide-ranging features that make your facility’s emergency power system more effective and efficient. Digital microprocessorbased technology streamlines and simplifies total generator load control and engine management. The entire control system fits into one enclosure. The technology is compatible with engines equipped with an electronic engine speed controller and voltage regulator. A significantly smaller footprint meets the demanding requirements of tight or unconventional floor spaces. Quicker manufacturing lead times and standardized configuration produce faster delivery. Door-mounted, software-based display screens communicate easy-to-understand information in less space. Digital metering measures voltage, amps, watts and frequency. It also includes protective relay functions as standard features. Drawout insulated-case circuit breakers that parallel the generator to the emergency bus are an integral part of the system’s design. The system is rated at 800 to 3,000 amperes per generator. It, of course, meets or exceeds the requirements of UL 891 and applicable standards of NEMA, IEEE, and ANSI. The system is labeled UL 891. 2 World-class technology for reliable power transfer Independent g e n e r ato r co n t ro l Independent Digital Generator Control Panels manage emergency standby systems comprised of up to four engine-generators Independent microprocessor-based Digital Generator Control Panels provide complete generator load control and engine management for generators ranging in capacity from 250 kW to 2 MW. Each control panel monitors an engine-generator, displays parameters for that engine-generator, annunciates generator and engine alarms, and controls engine speed and generator voltage for synchronizing and isochronous load sharing. 3 The panels automatically synchronize voltage and frequency, and match phase angles within two degrees of phase and 0.1 percent of voltage. Real (kW) load control and reactive (kVAR) controls are also included. Each control panel also operates its respective generator circuit breaker, integral to the system, for paralleling or shutdown. Safe dead bus closing ensures that only one gen- erator connects to the bus at a time. Using integrated control logic, the system transfers the highest priority block of load to the first engine-generator that produces acceptable voltage and frequency. Operator interface screens display: • System status • Engine status • Generator metering • DGCP input/output • Synchronization status • Load status • PF/kVAR status • Alarm/ Event log The control panels have five levels of built – in security to protect against configuration changes and alarm purges by unauthorized personnel. A laptop is not required to configure the system. A Modbus® RTU RS422 port enables communication to remote systems and allows those systems to access engine and generator parameters. Communication Products The optional ASCO 5500 Thin Web Server provides Web-enabled control. An operator or supervisor can monitor various transfer switch, engine and generator parameters remotely using the Thin Web Server. The server provides real time access and control of critical power system performance. Generator Breakers Generator circuit breakers offer drawout convenience to simplify maintenance or replacement. Users can manage, check system status and recognize potential system failure. It requires no dedicated hardware or software to operate and can be connected to any standard PC with a Microsoft® Internet Explorer browser. E-mail and text paging features alert users of abnormal conditions. Electrically-operated front-serviceable drawout breakers are available in 800 amp to 3000 amp frame sizes.The Square D, NW, 5.0P insulated case circuit breakers are UL 489 listed and are included with an adjustable long time delay, short time delay, instantaneous overcurrent trip and ground fault alarm. Additional features include 120VAC electrical operation, 24 VDC shunt ASCO 5500 Thin Web Server. The optional ASCO 5150 Connectivity Module provides Ethernet and RS485 Communications to Asco Transfer Switch controllers and Asco Power Managers. Embedded HTML pages are provided for monitoring of electrical parameters and alarms. The communication format will support up to 8 clients simultaniously over an Ethernet Connection. An ASCO 5110 communication module also available with only RS485 communications for monitoring and control with ASCO PowerQuest® systems. ASCO 5350 Remote Annunciator. trip, bell alarm, 4a and 4b auxiliary contacts, a protective cover for the manual close pushbutton, and instantaneous and ground fault indications. Square D Micrologic 5.0P Trip units provide monitoring of electrical parameters as well as visual indication. Trip settings are adjustable from 40 % to 100% of the generator breaker frame size and a Modbus® RTU port provides communications to the Emergency Power Communication System. Generator Protection • Device 27/59- Under • • • • • and Over Voltage Device 81- Under and Over Frequency Device 32- Reverse Power (Inverse Time Delay) Device 40- Loss of Excitation Device 81U- Bus Under Frequency Over Current (Inverse Time Delay) Synchronizing • Phase Match Synchronization • 3 Mode Operation: Run, Check, Permissive • Voltage Matching • Dead Bus Closing • Synch Timer • Reclose Attempt/Timer • Manual Synchronization (Permissive Mode) Generator Voltage And Reactive Load Control • Generator breaker and bus ampacity1,3 GEN SIZE (kw @480V) 230 - 500 300 - 650 350 - 800 450 -1000 550 -1250 700 -1500 800 -2000 indicate switch status and position, while separate push buttons individually initiate transfer switch operation and testing. Transfer switch annunciators can be set up in multiple locations to monitor various transfer switches, allowing redundant and distributed annunciation. Breaker Frame (Amps) Breaker Trip (Amps)2 800 1200 1200 1600 2000 2500 3000 800 1000 1200 1600 2000 2500 3000 1. Square D MASTERPACT® NW Insulated Case Circuit Breaker 2. Adjustable Trip Settings 40% to 100% of Breaker Frame Size 3. Bus bracing level 100,000 amperes. 8 Sy s t e m F u n c t i o n s • Power Factor Sharing In ASCO 5150 Connectivity Module. The ASCO 5350 Power Transfer Switch Remote Annunciator is a standalone, industrial grade interface device providing you with the most critical transfer switch status indication and transfer/ retransfer control for up to eight switches. Ethernet technology is built in for faster and more reliable communications. LEDs Maximum Reliability & Excellent Value 9 Phase &Neutral Bus (Amps) 2500 2500 2500 4000 4000 6000 6000 Ground Bus (Amps) 1000 1000 1000 1000 1000 2000 2000 • Load Sharing Mode Externally Adjustable Var/Pf Reference Manual Voltage Control AC Metering • 3 Phase Voltage • 3 Phase Current • kWh • kW, kVA, and kVAR • Power Factor • Frequency Engine Control • Multiple Crank Cycle Timer • Crank Timer • Crank Fail Alarm/ Shutdown • Crank Cutout (Rpm) • Engine Preglow • Idle/Rated Relay Output • Engine Runtime Engine Protection • Oil Pressure -Over/ Under Alarm/Shutdown Settings • Water Temperature - Over/Under Alarm/ Shutdown Settings • Battery Voltage - Over/ Under Alarm/Shutdown Settings • Overspeed - Alarm/ Shutdown Settings 4 Priority load management One priority block per generator with eight loads per block, such as electrically operated load distribution circuit breakers or power transfer switches, can be block load controlled. A Generator Control Station includes a five-position selector switch for each engine generator. The settings are lockout/reset, off/cooldown, automatic test off line and test on line. Indicator lights signal when the generator is running and when controls are not in the automatic operation. An under frequency monitor on the main bus monitors generator loading. Lowest priority loads will be shed automatically so critical priority one loads stay energized if the generators become overloaded, if one of the running generators fails, or if one of the generators fails to start when a power outage occurs. Visual indication identifies the status of priority load blocks and a push-button allows for a manual override of shed load blocks. Network Your Emergency Power System ATS Remote Annunciator Utility Power Twisted Pair Gen Communications 5 Ethernet Building Management System ASCO - Thin Web Server with Embedded HTML Pages for Monitoring and Control ASCO 5220D Power Manager Internet HUB Remote Access PC (Accessory LD) A System Control Station includes an alarm horn with alarm silence push-button. Push-buttons are also included for resetting priority two loads and the under frequency alarm. Visual indication provides status of priority two, three or four loads and emergency mode operation. Maintenance Room PC or Facility Network RS232 Engine Generator Engine Generator ASCO 5150 Connectivity Module RS485 MODBUS If an under-frequency bus condition is detected, the system will exit load demand mode and signal all additional engines to start and come online. If an engine fails while in load demand mode, all additional generators will be signaled to start and come online, and the lowest priority loads will be shed. HUB Engine Generator Communications Module ASCO Series 346 Generator Paralleling System (up to four engines) Load demand management Available on Two Engine Systems In the optional load demand mode with more than one generator online, the system monitors total load demand. If the load falls below 80% of rated output of the highest priority generators, lower priority engines (selectable) will shut down after an adjustable time delay. If the load increases above 90% of rated output of the highest priority generators already operating, the next priority engine will be signaled to start and come online after an adjustable time delay. ASCO communications products allow for the monitoring and control of your emergency or standby power distribution system. Local area networks and remote networks are supported with either single or multiple points of access, and web-enabled communications allow access to your power system from anywhere in the world. Email Server RS422 MODBUS RS485 RS485 To Additional Automatic Transfer Switches Legend ASCO 5110 Communication Module ASCO 5110 Communication Module ASCO Series 300 Automatic Transfer Switch ASCO 5110 Communication Module ASCO 4000 Series Automatic Transfer Switch ASCO 7000 Series Bypass Isolation Transfer Switch 6 RS232 Ethernet RS485 RS485 MODBUS RS422 MODBUS Email Pager ASCO 7000 Series Closed Transition-Bypass Isolation Transfer Switch 7 Communication Products The optional ASCO 5500 Thin Web Server provides Web-enabled control. An operator or supervisor can monitor various transfer switch, engine and generator parameters remotely using the Thin Web Server. The server provides real time access and control of critical power system performance. Generator Breakers Generator circuit breakers offer drawout convenience to simplify maintenance or replacement. Users can manage, check system status and recognize potential system failure. It requires no dedicated hardware or software to operate and can be connected to any standard PC with a Microsoft® Internet Explorer browser. E-mail and text paging features alert users of abnormal conditions. Electrically-operated front-serviceable drawout breakers are available in 800 amp to 3000 amp frame sizes.The Square D, NW, 5.0P insulated case circuit breakers are UL 489 listed and are included with an adjustable long time delay, short time delay, instantaneous overcurrent trip and ground fault alarm. Additional features include 120VAC electrical operation, 24 VDC shunt ASCO 5500 Thin Web Server. The optional ASCO 5150 Connectivity Module provides Ethernet and RS485 Communications to Asco Transfer Switch controllers and Asco Power Managers. Embedded HTML pages are provided for monitoring of electrical parameters and alarms. The communication format will support up to 8 clients simultaniously over an Ethernet Connection. An ASCO 5110 communication module also available with only RS485 communications for monitoring and control with ASCO PowerQuest® systems. ASCO 5350 Remote Annunciator. trip, bell alarm, 4a and 4b auxiliary contacts, a protective cover for the manual close pushbutton, and instantaneous and ground fault indications. Square D Micrologic 5.0P Trip units provide monitoring of electrical parameters as well as visual indication. Trip settings are adjustable from 40 % to 100% of the generator breaker frame size and a Modbus® RTU port provides communications to the Emergency Power Communication System. Generator Protection • Device 27/59- Under • • • • • and Over Voltage Device 81- Under and Over Frequency Device 32- Reverse Power (Inverse Time Delay) Device 40- Loss of Excitation Device 81U- Bus Under Frequency Over Current (Inverse Time Delay) Synchronizing • Phase Match Synchronization • 3 Mode Operation: Run, Check, Permissive • Voltage Matching • Dead Bus Closing • Synch Timer • Reclose Attempt/Timer • Manual Synchronization (Permissive Mode) Generator Voltage And Reactive Load Control • Generator breaker and bus ampacity1,3 GEN SIZE (kw @480V) 230 - 500 300 - 650 350 - 800 450 -1000 550 -1250 700 -1500 800 -2000 indicate switch status and position, while separate push buttons individually initiate transfer switch operation and testing. Transfer switch annunciators can be set up in multiple locations to monitor various transfer switches, allowing redundant and distributed annunciation. Breaker Frame (Amps) Breaker Trip (Amps)2 800 1200 1200 1600 2000 2500 3000 800 1000 1200 1600 2000 2500 3000 1. Square D MASTERPACT® NW Insulated Case Circuit Breaker 2. Adjustable Trip Settings 40% to 100% of Breaker Frame Size 3. Bus bracing level 100,000 amperes. 8 Sy s t e m F u n c t i o n s • Power Factor Sharing In ASCO 5150 Connectivity Module. The ASCO 5350 Power Transfer Switch Remote Annunciator is a standalone, industrial grade interface device providing you with the most critical transfer switch status indication and transfer/ retransfer control for up to eight switches. Ethernet technology is built in for faster and more reliable communications. LEDs Maximum Reliability & Excellent Value 9 Phase &Neutral Bus (Amps) 2500 2500 2500 4000 4000 6000 6000 Ground Bus (Amps) 1000 1000 1000 1000 1000 2000 2000 • Load Sharing Mode Externally Adjustable Var/Pf Reference Manual Voltage Control AC Metering • 3 Phase Voltage • 3 Phase Current • kWh • kW, kVA, and kVAR • Power Factor • Frequency Engine Control • Multiple Crank Cycle Timer • Crank Timer • Crank Fail Alarm/ Shutdown • Crank Cutout (Rpm) • Engine Preglow • Idle/Rated Relay Output • Engine Runtime Engine Protection • Oil Pressure -Over/ Under Alarm/Shutdown Settings • Water Temperature - Over/Under Alarm/ Shutdown Settings • Battery Voltage - Over/ Under Alarm/Shutdown Settings • Overspeed - Alarm/ Shutdown Settings 4 Priority load management One priority block per generator with eight loads per block, such as electrically operated load distribution circuit breakers or power transfer switches, can be block load controlled. A Generator Control Station includes a five-position selector switch for each engine generator. The settings are lockout/reset, off/cooldown, automatic test off line and test on line. Indicator lights signal when the generator is running and when controls are not in the automatic operation. An under frequency monitor on the main bus monitors generator loading. Lowest priority loads will be shed automatically so critical priority one loads stay energized if the generators become overloaded, if one of the running generators fails, or if one of the generators fails to start when a power outage occurs. Visual indication identifies the status of priority load blocks and a push-button allows for a manual override of shed load blocks. Network Your Emergency Power System ATS Remote Annunciator Utility Power Twisted Pair Gen Communications 5 Ethernet Building Management System ASCO - Thin Web Server with Embedded HTML Pages for Monitoring and Control ASCO 5220D Power Manager Internet HUB Remote Access PC (Accessory LD) A System Control Station includes an alarm horn with alarm silence push-button. Push-buttons are also included for resetting priority two loads and the under frequency alarm. Visual indication provides status of priority two, three or four loads and emergency mode operation. Maintenance Room PC or Facility Network RS232 Engine Generator Engine Generator ASCO 5150 Connectivity Module RS485 MODBUS If an under-frequency bus condition is detected, the system will exit load demand mode and signal all additional engines to start and come online. If an engine fails while in load demand mode, all additional generators will be signaled to start and come online, and the lowest priority loads will be shed. HUB Engine Generator Communications Module ASCO Series 346 Generator Paralleling System (up to four engines) Load demand management Available on Two Engine Systems In the optional load demand mode with more than one generator online, the system monitors total load demand. If the load falls below 80% of rated output of the highest priority generators, lower priority engines (selectable) will shut down after an adjustable time delay. If the load increases above 90% of rated output of the highest priority generators already operating, the next priority engine will be signaled to start and come online after an adjustable time delay. ASCO communications products allow for the monitoring and control of your emergency or standby power distribution system. Local area networks and remote networks are supported with either single or multiple points of access, and web-enabled communications allow access to your power system from anywhere in the world. Email Server RS422 MODBUS RS485 RS485 To Additional Automatic Transfer Switches Legend ASCO 5110 Communication Module ASCO 5110 Communication Module ASCO Series 300 Automatic Transfer Switch ASCO 5110 Communication Module ASCO 4000 Series Automatic Transfer Switch ASCO 7000 Series Bypass Isolation Transfer Switch 6 RS232 Ethernet RS485 RS485 MODBUS RS422 MODBUS Email Pager ASCO 7000 Series Closed Transition-Bypass Isolation Transfer Switch 7 Priority load management One priority block per generator with eight loads per block, such as electrically operated load distribution circuit breakers or power transfer switches, can be block load controlled. A Generator Control Station includes a five-position selector switch for each engine generator. The settings are lockout/reset, off/cooldown, automatic test off line and test on line. Indicator lights signal when the generator is running and when controls are not in the automatic operation. An under frequency monitor on the main bus monitors generator loading. Lowest priority loads will be shed automatically so critical priority one loads stay energized if the generators become overloaded, if one of the running generators fails, or if one of the generators fails to start when a power outage occurs. Visual indication identifies the status of priority load blocks and a push-button allows for a manual override of shed load blocks. Network Your Emergency Power System ATS Remote Annunciator Utility Power Twisted Pair Gen Communications 5 Ethernet Building Management System ASCO - Thin Web Server with Embedded HTML Pages for Monitoring and Control ASCO 5220D Power Manager Internet HUB Remote Access PC (Accessory LD) A System Control Station includes an alarm horn with alarm silence push-button. Push-buttons are also included for resetting priority two loads and the under frequency alarm. Visual indication provides status of priority two, three or four loads and emergency mode operation. Maintenance Room PC or Facility Network RS232 Engine Generator Engine Generator ASCO 5150 Connectivity Module RS485 MODBUS If an under-frequency bus condition is detected, the system will exit load demand mode and signal all additional engines to start and come online. If an engine fails while in load demand mode, all additional generators will be signaled to start and come online, and the lowest priority loads will be shed. HUB Engine Generator Communications Module ASCO Series 346 Generator Paralleling System (up to four engines) Load demand management Available on Two Engine Systems In the optional load demand mode with more than one generator online, the system monitors total load demand. If the load falls below 80% of rated output of the highest priority generators, lower priority engines (selectable) will shut down after an adjustable time delay. If the load increases above 90% of rated output of the highest priority generators already operating, the next priority engine will be signaled to start and come online after an adjustable time delay. ASCO communications products allow for the monitoring and control of your emergency or standby power distribution system. Local area networks and remote networks are supported with either single or multiple points of access, and web-enabled communications allow access to your power system from anywhere in the world. Email Server RS422 MODBUS RS485 RS485 To Additional Automatic Transfer Switches Legend ASCO 5110 Communication Module ASCO 5110 Communication Module ASCO Series 300 Automatic Transfer Switch ASCO 5110 Communication Module ASCO 4000 Series Automatic Transfer Switch ASCO 7000 Series Bypass Isolation Transfer Switch 6 RS232 Ethernet RS485 RS485 MODBUS RS422 MODBUS Email Pager ASCO 7000 Series Closed Transition-Bypass Isolation Transfer Switch 7 Communication Products The optional ASCO 5500 Thin Web Server provides Web-enabled control. An operator or supervisor can monitor various transfer switch, engine and generator parameters remotely using the Thin Web Server. The server provides real time access and control of critical power system performance. Generator Breakers Generator circuit breakers offer drawout convenience to simplify maintenance or replacement. Users can manage, check system status and recognize potential system failure. It requires no dedicated hardware or software to operate and can be connected to any standard PC with a Microsoft® Internet Explorer browser. E-mail and text paging features alert users of abnormal conditions. Electrically-operated front-serviceable drawout breakers are available in 800 amp to 3000 amp frame sizes.The Square D, NW, 5.0P insulated case circuit breakers are UL 489 listed and are included with an adjustable long time delay, short time delay, instantaneous overcurrent trip and ground fault alarm. Additional features include 120VAC electrical operation, 24 VDC shunt ASCO 5500 Thin Web Server. The optional ASCO 5150 Connectivity Module provides Ethernet and RS485 Communications to Asco Transfer Switch controllers and Asco Power Managers. Embedded HTML pages are provided for monitoring of electrical parameters and alarms. The communication format will support up to 8 clients simultaniously over an Ethernet Connection. An ASCO 5110 communication module also available with only RS485 communications for monitoring and control with ASCO PowerQuest® systems. ASCO 5350 Remote Annunciator. trip, bell alarm, 4a and 4b auxiliary contacts, a protective cover for the manual close pushbutton, and instantaneous and ground fault indications. Square D Micrologic 5.0P Trip units provide monitoring of electrical parameters as well as visual indication. Trip settings are adjustable from 40 % to 100% of the generator breaker frame size and a Modbus® RTU port provides communications to the Emergency Power Communication System. Generator Protection • Device 27/59- Under • • • • • and Over Voltage Device 81- Under and Over Frequency Device 32- Reverse Power (Inverse Time Delay) Device 40- Loss of Excitation Device 81U- Bus Under Frequency Over Current (Inverse Time Delay) Synchronizing • Phase Match Synchronization • 3 Mode Operation: Run, Check, Permissive • Voltage Matching • Dead Bus Closing • Synch Timer • Reclose Attempt/Timer • Manual Synchronization (Permissive Mode) Generator Voltage And Reactive Load Control • Generator breaker and bus ampacity1,3 GEN SIZE (kw @480V) 230 - 500 300 - 650 350 - 800 450 -1000 550 -1250 700 -1500 800 -2000 indicate switch status and position, while separate push buttons individually initiate transfer switch operation and testing. Transfer switch annunciators can be set up in multiple locations to monitor various transfer switches, allowing redundant and distributed annunciation. Breaker Frame (Amps) Breaker Trip (Amps)2 800 1200 1200 1600 2000 2500 3000 800 1000 1200 1600 2000 2500 3000 1. Square D MASTERPACT® NW Insulated Case Circuit Breaker 2. Adjustable Trip Settings 40% to 100% of Breaker Frame Size 3. Bus bracing level 100,000 amperes. 8 Sy s t e m F u n c t i o n s • Power Factor Sharing In ASCO 5150 Connectivity Module. The ASCO 5350 Power Transfer Switch Remote Annunciator is a standalone, industrial grade interface device providing you with the most critical transfer switch status indication and transfer/ retransfer control for up to eight switches. Ethernet technology is built in for faster and more reliable communications. LEDs Maximum Reliability & Excellent Value 9 Phase &Neutral Bus (Amps) 2500 2500 2500 4000 4000 6000 6000 Ground Bus (Amps) 1000 1000 1000 1000 1000 2000 2000 • Load Sharing Mode Externally Adjustable Var/Pf Reference Manual Voltage Control AC Metering • 3 Phase Voltage • 3 Phase Current • kWh • kW, kVA, and kVAR • Power Factor • Frequency Engine Control • Multiple Crank Cycle Timer • Crank Timer • Crank Fail Alarm/ Shutdown • Crank Cutout (Rpm) • Engine Preglow • Idle/Rated Relay Output • Engine Runtime Engine Protection • Oil Pressure -Over/ Under Alarm/Shutdown Settings • Water Temperature - Over/Under Alarm/ Shutdown Settings • Battery Voltage - Over/ Under Alarm/Shutdown Settings • Overspeed - Alarm/ Shutdown Settings 4 Ordering i n fo r m at i o n To order an ASCO 346 Series Generator Paralleling System, complete the following catalog number. 346 0800 M N 6 Product Amperes Lug Type Voltage Code1 Frequency Code 346 (2 Gens) 347 (4 Gens) 0800 1000 M C Mechanical Compression 1200 1600 2000 2500 3000 A B C D E F H J K L M N P Q R 115 120 208 220 230 240 380 400 415 440 460 480 550 575 600 5 6 50 Hz 60 Hz 4 C1 Enclosure Depth2 4 6 7 8 Enclosure3 C1 NEMA Type 1 ANSI 61 Gray F1 NEMA Type 3R ANSI 61 Gray C2 NEMA Type 1 ANSI 49 Gray F2 NEMA Type 3R ANSI 49 Gray 48” 60” 72” 84” 1. Consult the factory for systems other than 3 phase, 4 wire 2. Nema 1 systems 1200 amps and below are provided at 48” deep standard with an option to increase the depth to 60” or 72”. Nema 1 systems 1600 amps and above are provided 60” deep as standard with an option to increase the depth to 72”. Nema 3R systems 1200 amps and below are provided 60” deep standard with an option to increase the depth to 72” or 84”. Nema 3R systems 1600 amps are provided 72” deep standard with an option to increase the depth to 84”. 3. ANSI 61 Gray Standard. The Example Catalog Number Above is 3460800MN64C Sizes of UL-Listed Solderless Screw-Type Terminals for External Power Connections Max # of Max # of Generator Breaker Conductors per Conductors per Rating amps Gen Terminal Load Terminal 800 1000 1200 1600 2000 2500 3000 4 5 5 6 7 8 9 8 10 10 12 14 16 18 Range of CU Range of AL Max # of Ground Bus Conductors Conductor Sizes Conductor Sizes 2 3 3 3 4 4 5 3/0 to 800 MCM 3/0 to 800 MCM 3/0 to 800 MCM 3/0 to 800 MCM 3/0 to 800 MCM 3/0 to 800 MCM 3/0 to 800 MCM 250 to 800 MCM 250 to 800 MCM 250 to 800 MCM 250 to 800 MCM 250 to 800 MCM 250 to 800 MCM 250 to 800 MCM Pull Box Options3 Pull Box with out provisions for overhead lifting device1 Enclosure Depth in (mm) 48 (1219) 60 (1524) 72 (1829) Accessory Height in (mm) Depth Accessory Height in (mm) Depth in (mm) 42A1 42A2 42A3 12 (305) 12 (305) 12 (305) 48 (1219) 60 (1524) 72 (1829) 42A4 42A5 42A6 24 (610) 24 (610) 24 (610) 48 (1219) 60 (1524) 72 (1829) Pull Box with provisions for overhead lifting device 1,2 Enclosure Depth in (mm) 48 (1219) 60 (1524) 72 (1829) Accessory Height in (mm) Depth Accessory Height in (mm) Depth in (mm) 42B1 42B2 42B3 12 (305) 12 (305) 12 (305) 24 (610) 36 (914) 48 (1219) 42B4 42B5 42B6 24 (610) 24 (610) 24 (610) 24 (610) 36 (914) 48 (1219) 1. All pull boxes are Nema 1, top mounted 36” wide. 2. An overhead circuit breaker lifting device with trolley, rails and mounting rails is available.Order as accessory 82. 3. Shipped separately, must be installed by contractor. 10 Dimensions and Shipping Weights NEMA 1 (per section)** 800-1200 Amp * Optional Enclosure Depths Code, 6 - 60 Inches Code, 7 - 72 Inches Shipping Weights** Amps 800 - 1200 800 - 1200 800 - 1200 * Depth in(mm) Enclosed Weight lb(kg) 48 (1219) 60 (1524) 72 (1829) 1964 (892) 2024 (920) 2085 (948) Dimensions and Shipping Weights NEMA 1 (per section)** 1600-3000 Amp * Optional Enclosure Depths Code, 7 - 72 Inches Shipping Weights** Amps 1600 - 2000 1600 - 2000 2500 - 3000 2500 - 3000 * Enclosed Depth in(mm) Weight lb(kg) 60 (1524) 72 (1829) 60 (1524) 72 (1829) 2085 (947) 2206 (1003) 2385 (1084) 2506 (1139) **Single section for two-generator systems; second section required for four generator systems 11 Dimensions and Shipping Weights NEMA 3R (per section)** 800-1200 Amp * Optional Enclosure Depths Code, 7 - 72 Inches Code, 8 - 84 Inches Shipping Weights** Amps 800 - 1200 800 - 1200 800 - 1200 Depth in(mm) 60 (1524) 72 (1829) 84 (2134) * Enclosed Weight lb(kg) 2274 (1034) 2334 (1061) 2395 (1089) Dimensions and Shipping Weights NEMA 3R (per section)** 1600-3000 Amp * Optional Enclosure Depths Code, 8 - 84 Inches Shipping Weights** Amps 1600 - 2000 1600 - 2000 2500 - 3000 2500 - 3000 Depth in(mm) 72 (1829) 84 (2134) 72 (1829) 84 (2134) Enclosed Weight lb(kg) * 2395 (1089) 2516 (1144) 2695 (1225) 2739 (1245) **Single section for two-generator systems; second section required for four generator systems 12 A SCO Power Te chnologies 50 Hanover Road F l o r ham Park, NJ 07932 USA 8 0 0 8 0 0 A SCO w w w. ascopower.com w w w. ascoapu. co m Emerson Network Power. The global leader in enabling Business-Critical ContinuityTM. EmersonNetworkPower.com Outside Plant AC Power Connectivity Embedded Computing Embedded Power DC Power Infrastructure Management & Monitoring Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2009 Emerson Electric Co. Publication 3121 R4 © May, 2009 Printed in the U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2009:05:14 11:10:40-04:00 Creator : Adobe InDesign CS2 (4.0) Modify Date : 2009:06:01 10:15:21-04:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2009:06:01 10:15:21-04:00 Creator Tool : Adobe InDesign CS2 (4.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 13027 bytes, use -b option to extract) Instance ID : uuid:35a85aea-c363-484b-ba3b-655cbd43c0d6 Document ID : adobe:docid:indd:a700e34e-3a50-11de-ad7d-8aff8c6e0cfe Rendition Class : proof:pdf Derived From Instance ID : 5b862372-499c-11dc-a897-c8243c5f3317 Derived From Document ID : adobe:docid:indd:5b862370-499c-11dc-a897-c8243c5f3317 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 300.00, 350.00, 300.00, 300.00, 300.00, 300.00, 300.00, 450.00, 300.00, 200.00, 200.00, 200.00, 200.00, 72.00 Manifest Placed Y Resolution : 72.00, 300.00, 350.00, 300.00, 300.00, 300.00, 300.00, 300.00, 450.00, 300.00, 200.00, 200.00, 200.00, 200.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:C912A87C9A49DC11ADECF0F401536A36, uuid:632AB7B647BCDB11BC51D5DFA55AA735, uuid:E5E85F1B9BC6DB119406EC7F964BD071, uuid:66BD3FFCBC3FDE118BCCAA2BD33FD877, uuid:0A5A43A92B9CDC11879AFB5AC9368B44, uuid:2D39B111D5F9DC11A77BC68E13D5FC57, uuid:80BBB44EC43FDE11BA8EC0CF35B54D74 Manifest Reference Document ID : uuid:6799b69b-2671-4a38-949d-8f3305e3ca78, adobe:docid:photoshop:11703520-bee7-11d8-9e19-cfc3423ee14a, adobe:docid:photoshop:f4bd2034-5f08-11d8-b674-adbb4a4a0d86, adobe:docid:photoshop:d5dea711-e358-11d9-bc34-da7556b1a1e3, uuid:ACFDF2E27EBBDB11A58180E253D4A507, adobe:docid:photoshop:11703520-bee7-11d8-9e19-cfc3423ee14a, adobe:docid:photoshop:0254ed42-6170-11d8-bbf7-aae341192b55, uuid:38214DF32A9CDC11879AFB5AC9368B44, adobe:docid:photoshop:3a255a4a-619b-11d8-9355-c93e506c7e4b, uuid:2839B111D5F9DC11A77BC68E13D5FC57, adobe:docid:photoshop:7fdb6b63-4233-11d8-932c-eb76de485d1a, adobe:docid:photoshop:4a90e34a-42d5-11d8-99a5-be069b179ad6, adobe:docid:photoshop:bc38efe0-42e7-11d8-99a5-be069b179ad6, adobe:docid:photoshop:c0865192-4236-11d8-aca9-bb5f2ae6175c, uuid:7FBBB44EC43FDE11BA8EC0CF35B54D74 Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 14EXIF Metadata provided by EXIF.tools