Emerson Cp200 Series Pressure Loaded Reducing Regulators Data Sheet
2015-03-30
: Emerson Emerson-Cp200-Series-Pressure-Loaded-Pressure-Reducing-Regulators-Data-Sheet-681093 emerson-cp200-series-pressure-loaded-pressure-reducing-regulators-data-sheet-681093 emerson pdf
Open the PDF directly: View PDF 
.
Page Count: 28
Bulletin 71.1:CP200
December 2013
D103135X012
www.fisherregulators.com
CP200 Series Commercial / Industrial Pressure-
Loaded Pressure Reducing Regulator
• Wide Range of NPT Body Sizes
• Easy to Install and Maintain
• Highly Con gurable
• Secondary Seat™ Protection
Features and Bene ts
Figure 1. CP200 Series Pressure Loaded Regulator
• Only Standard Tools Required for Pressure
Adjustment and Ori ce Removal
• Fixed Factor / Pressure Factor
Measurement (PFM) Accuracy Capabilities
Bulletin 71.1:CP200
2
Introduction
The CP200 Series pressure loaded regulators have
been engineered to t a multitude of pressure reducing
applications including commercial and industrial
installations. The CP200 Series provides accurate
control for use in pressure factor measurement ( xed
factor billing) applications. This exibility is provided
by the various body end connection sizes, outlet
pressure settings, and ori ce sizes.
Figure 2. Typical CP200 Series Cut-away View
VALVE DISK
LOWER
CASING
TYPE 67CP PRESSURE
LOADING REGULATOR
CLOSING
SPRING
DIAPHRAGM
DIAPHRAGM
HEAD
LEVER
ORIFICE
VALVE STEM
EXTERNAL
CONTROL LINE
PLUG (DO NOT
REMOVE IF UNIT IS
PRESSURIZED)
Overpressure Protection Options
Available:
• Token Relief—Provides a small capacity or token
relief located in the Type 67CPR pressure loading
regulator that relieves minor overpressure caused by
thermal expansion or minor nicks in the ori ce or disk.
• Secondary Seat™ Protection—Provides lockup
via a secondary seating and disk surface in the
event that damage to the primary disk or ori ce
seating surface, or debris in the ow path, inhibit
primary lockup. Secondary Seat protection does
not provide additional overpressure protection in
the event the secondary seat or disk is damaged
by debris or contamination in the pipeline or from
conditions that would cause the regulator to go
wide open. See page 6 for additional information.
Bulletin 71.1:CP200
3
1. The pressure/temperature limits in this Bulletin or any applicable standard limitation should not be exceeded.
2. Product has passed Emerson Process Management Regulator Technologies, Inc. testing for lockup, relief start-to-discharge and reseal down to -40 degrees.
Available Congurations
See Table 1
Body Sizes, Material, End Connections, and
Pressure Rating(1)
See Table 2
Inlet Pressure Ratings(1)
See Table 3
Maximum Outlet Pressures(1)
Emergency Casing: 25 psig / 1.7 bar
Operating: 20 psig / 1.4 bar
Outlet Pressure Range
1 to 20 psig / 69 mbar to 1.4 bar
See Table 4
Flow Capacities
See Tables 6 through 23
Flow Coefcients and Orice Sizes
See Table 3
IEC Sizing Coefcients
See Table 3
Temperature Capabilities(1)(2)
-20 to 150°F / -29 to 66°C
Pressure Registration
Internal
Pressure Loading Regulator Spring Case Connection
1/4 NPT
Factory Setpoint Inlet Pressures for Various
Orice Sizes
1/8 inch / 3.1 mm: 80 psig / 5.5 bar
3/16 inch / 4.7 mm: 60 psig / 4.1 bar
1/4 inch / 6.4 mm: 40 psig / 2.8 bar
5/16 inch / 7.9 mm: 30 psig / 2.1 bar
3/8 inch / 9.5 mm: 25 psig / 1.7 bar
1/2 inch / 13 mm: 25 psig / 1.7 bar
Token Relief Performance
Approximate Token Relief Start-to-Discharge:
See Table 5
Approximate Weight
10 pounds / 5 kg
Construction Materials
Type CP200IN Main Valve and Actuator
Body: Gray Cast Iron
Body O-ring: Nitrile (NBR)
Closing Cap: Aluminum
Adjusting Screw: Aluminum
Diaphragm Case, Spring Case,
and Valve Stem: Aluminum
Diaphragm Plate: Steel
Orice: Aluminum
Pusher Post: Aluminum
Diaphragm and Disk: Nitrile (NBR)
Closing Spring: Stainless steel
Relief Valve Spring: Stainless steel
Relief Valve Spring Retainer: Zinc-plated steel
Relief Valve Seat: Aluminum
Lever: Zinc-plated steel
Lever Pin: Stainless steel
Spring Seat: Aluminum
67CP Series Pressure Loading Regulator
Spring: Stainless steel
Body: Aluminum
O-ring and Soft Seat: Nitrile (NBR)
Valve Stem: Aluminum
Valve Plug: Nitrile (NBR)
Diaphragm: Nitrile (NBR)
Designed, Tested, and Evaluated Consistent With:
ASME B16, ASME Section VIII DIV I, ASTM B117
(Corrosion Resistance)
Specications
The Specications section lists the specications for the CP200 Series Regulators. The following information is
stamped on the nameplate of CP200 Series: Type Number, Maximum Outlet Pressure, and Spring Range.
Bulletin 71.1:CP200
4
TYPE NUMBER OPTIONS
C P 2 0
OVERPRESSURE PROTECTION MODULE
0Without Overpressure Protection Module
5With Secondary Seat™ Protection
6With Secondary Seat Protection with bleed to indicate Secondary Seat is functioning
PRESSURE REGISTRATION
IInternal Registration
RELIEF
NNon-Relief
TToken Internal Relief
Table 1. Available Configurations
Table 3. Inlet Pressure Ratings and Flow and Sizing Coeffiecients
TYPE ORIFICE SIZE MAXIMUM OPERATING
INLET PRESSURE(1)(2)
FLOW COEFFICIENTS
(WIDE-OPEN) C1
IEC SIZING COEFFICIENTS
Inch mm psig bar CgCvXTFDFL
CP200
1/8 3.2 125 8.6 12 0.40 30 0.53 0.87
0.89
3/16 4.8 125 8.6 24 0.80 30 0.58 0.82
1/4 6.4 125 8.6 44 1.52 29 0.53 0.85
3/8 9.5 60 4.1 102 3.30 31 0.60 0.83
1/2 13 40 2.8 172 4.40 39 0.97 0.72
CP205 and
CP206
1/8 3.2 125 8.6 12 0.4 30 0.53 0.87
3/16 4.8 125 8.6 24 0.8 30 0.58 0.82
1/4 6.4 125 8.6 44 1.52 29 0.53 0.85
5/16 7.9 100 6.9 70 2.7 30 0.53 0.85
1. Inlet pressures based on lockup performance. For maximum inlet pressure values with optimum regulating performance refer to the applicable Flow Capacity table.
2. To comply with ANSI B109.4 relief requirements, the maximum inlet pressure may need to be reduced.
Table 2. Body Sizes, Material, End Connection, and Pressure Rating
TYPE BODY SIZE END
CONNECTION BODY MATERIAL FACE-TO-FACE DIMENSION PRESSURE RATING
Inch mm psig bar
CP200, CP205,
and CP206
3/4
NPT Gray Cast Iron 4 102 175 12.1
3/4 x 1
3/4 x 1-1/4
1
1 x 1-1/4
1-1/4
Bulletin 71.1:CP200
5
Principle of Operation
Refer to Figure 3. The CP200 Series has spring-to-
close construction and uses a 67CP Series pressure
loading regulator to supply loading pressure to the top
of the main diaphragm. Adjustment to the downstream
pressure is therefore made by adjusting the loading
pressure regulator. The load pressure supplied by the
loading regulator is constant and equal to the desired
downstream pressure plus the pressure required to
overcome the light closing spring.
Type CP200 Base Regulator
Increasing Downstream Demand
As downstream demand increases the outlet
pressure registering on the underside of the main
diaphragm decreases and the constant loading
pressure above the main diaphragm forces the
diaphragm downward. This downward diaphragm
motion is transferred through the lever causing the
main disk to move away from the orice seating
surface to supply additional ow downstream to the
required demand.
Decreasing Downstream Demand
As downstream demand decreases the outlet
pressure registering on the underside of the main
diaphragm increases forcing the main diaphragm
upward. This upward motion is transferred through
the lever causing the main disk to move toward the
orice seating surface to reduce ow to meet the
required demand.
Zero Downstream Demand (Lockup)
As downstream demand decreases further, the outlet
pressure registering under the main diaphragm
together with the closing spring act to close the
main disk against the orice seating surface. At this
point the loading regulator will continue to supply
a small amount of gas downstream that is equal to
the capacity of the bleed restriction in the diaphragm
assembly. As downstream demand decreases to zero
ow outlet pressure rises to meet the lock-up pressure
of the loading regulator. This causes the loading
regulator to lockup to stop all ow downstream.
Figure 3. Type CP200IN Pressure Loaded Pressure Reducing Regulator with Internal Registration Operational Schematic
M1129
CLOSING SPRING
DIAPHRAGM
CONTROL SPRING
VALVE DISK
ORIFICE
VALVE STEM
LEVER
PRESSURE RETAINING
PLUG (DO NOT REMOVE)
MAIN REGULATOR
TYPE 67CP PRESSURE
LOADING REGULATOR
INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE
LOADING PRESSURE
Bulletin 71.1:CP200
6
Figure 4. Type CP205IT Pressure Loaded Pressure Reducing Regulator with Internal Registration and Token Relief Operational Schematic
CLOSING SPRING
DIAPHRAGM
CONTROL SPRING
VALVE STEM
LEVER
PRESSURE RETAINING
PLUG (DO NOT REMOVE)
MAIN REGULATOR
TYPE 67CP PRESSURE
LOADING REGULATOR
SECONDARY SEAT™ DETAIL
INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE
LOADING PRESSURE
M1165
4
CP200 Series with Secondary SeatTM Protection
CONTROL SPRING
RELIEF V LVE STEM
VALVE STEM
SECONDARY SEAT DETAIL
SECONDARY SEAT DETAILED VIEW
NORMAL OPERATION NORMAL LOCKUP DEBRIS OBSTRUCTING
LOCKUP
SECONDARY SEAT
LOCKUP
TYPE CP206
SECONDARY SEAT WITH METAL
TO METAL BLEED
PRIMARY DISK PRIMARY ORIFICE
SEATING SURFACE
SECONDARY SEATING
SURFACE
SECONDARY
ORIFICE SEATING
SURFACE
Bulletin 71.1:CP200
7
Type CP205 with Secondary Seat™
Protection
Refer to Figure 4. The Type CP205 provides
Secondary Seat Protection. As downstream demand
decreases and downstream pressure rises to the
regulator pressure lock-up value, the regulator will
lockup. If, however, damage has occurred to the
primary disk, to the primary orice’s seating surface, or
debris has become lodged between the primary disk
and primary orice, the outlet pressure will continue
to rise. This additional pressure causes the primary
disk to apply additional force to the orice seating
surface, which causes the Secondary seating surface
to move toward the Secondary disk or sealing surface.
If downstream demand decreases to zero, then the
secondary seating surface will contact the sealing
surface to provide lockup.
Type CP206 with Secondary Seat
Protection with Bleed
The Type CP206 provides small bleed to the
downstream system as an indication that the
Secondary Seat is providing lockup. In the event that
the primary orice and disk cannot provide lockup, the
secondary seating surface will move into contact with
a metal disk. This metal to metal interface will allow
a small amount of gas to bleed downstream thereby
increasing outlet pressure until the internal relief valve
begins to discharge gas to the atmosphere. The
odor of this discharged gas provides an indication
that the regulator is relying on the Secondary Seat for
overpressure protection.
Types CP205 and CP206
Secondary Seat Protection Limitations
Secondary Seat Protection does not provide additional
overpressure protection in the event the secondary
seating surface or disk is damaged by debris or
contamination in the pipeline or from conditions that
would cause the regulator to go wide open. When
selecting Secondary Seat Protection option, it is
recommended that:
• Other additional overpressure protection methods
be added in the downstream system as discussed
in the section on Overpressure Protection; and
• An annual downstream lock-up pressure test be
done to determine if the Secondary Seat Protection
option is operating and functional.
Installation
The CP200 Series regulators may be installed in
any position. However, the spring case vent of the
Type 67CP loading regulator should be pointed
downward. If gas escaping through Type 67CPR
pressure loading regulator token internal relief valve
could constitute a hazard, the spring case vent must
be piped to a location where escaping gas will not be
hazardous. If the vented gas will be piped to another
location, obstruction-free tubing or piping at least
equal to the vent, and the end of the vent pipe must
be protected from anything that might clog it.
Overpressure Protection
The CP200 Series is an internally registered pressure
reducing regulator and has outlet pressure ratings
lower than the inlet pressure ratings. Complete
downstream overpressure protection is needed if the
actual inlet pressure exceeds the outlet pressure rating.
Token Relief
Types with a “T” in the type number, e.g., Type CP200IT
provide an optional small capacity or token relief located
in the Type 67CPR to relieve minor overpressure
caused by thermal expansion or minor nicks in the
orice or disk. Refer to Table 5 for Start-to-Discharge
Pressure Above Setpoint values.
Secondary Seat™ Protection
This overpressure protection provides lockup via a
secondary seating and disk surface in the event that
damage to the primary disk or orice seating surface,
or debris in the ow path, inhibit primary lockup.
Overpressuring any portion of a regulator or
associated equipment may cause personal injury,
leakage, or property damage due to bursting of
pressure-containing parts or explosion of accumulated
gas. Provide appropriate pressure relieving or
pressure limiting devices to ensure that the limits in
the Specications section is not exceeded. Regulator
operation within ratings does not prevent the possibility
of damage from external sources or from debris in the
pipeline. Refer to the relief sizing coefcients and the
Capacity Information section to determine the required
relief valve capacity.
Bulletin 71.1:CP200
8
Capacity Information
Tables 6 through 23 give the CP200 Series natural
gas regulating capacities at selected inlet pressures,
outlet pressure settings and body outlet sizes. Flows
are in SCFH (60°F and 14.7 psia) and Nm³/h (0°C and
1.01325 bar) of 0.6 speci c gravity gas. To determine
equivalent capacities for air, propane, butane, or
nitrogen, multiply the capacity number in the tables by
the following appropriate conversion factor: 0.775 for
air, 0.628 for propane, 0.548 for butane, or 0.789 for
nitrogen. For gases of other speci c gravities, multiply
the given capacity by 0.775 and divide by the square
root of the appropriate speci c gravity.
The published capacities were obtained using inlet
and outlet piping the same size as the regulator
body size.
Relief Sizing
For critical fl ow:
To determine wide-open ow capacities for relief sizing
of 0.6 speci c gravity natural gas at 60°F at critical
pressure drops (absolute outlet pressure equal to
approximately one-half or less than one-half of the
absolute inlet pressure), use the following formula:
Q= P1abs(Cg)(1.29)
Table 4. Outlet Pressure Ranges
OUTLET PRESSURE RANGE(1)
PART NUMBER SPRING COLOR SPRING WIRE DIAMETER SPRING FREE LENGTH
psig bar Inch mm Inch mm
1 to 2 69 mbar to 0.14 bar GE30199X012 Yellow Stripe 0.078 2.0 1.35 34.3
2 to 5 0.14 to 0.34 GE27213X012 Orange Stripe 0.100 2.5 1.47 37.3
5 to 10 0.34 to 0.69 GE39890X012 Black Stripe 0.114 2.9 1.47 37.3
10 to 20 0.69 to 1.4 GE30200X012 Purple Stripe 0.137 3.5 1.42 36.1
1. Oulet pressure range is controlled by 67CP Series pressure loading regulator spring.
SPRING RANGE(1)
PART NUMBER SPRING COLOR
START-TO-DISCHARGE PRESSURE
RANGE ABOVE SETPOINT
psig bar psig mbar
1 to 2 69 mbar to 0.14 bar GE30199X012 Yellow Stripe 1 to 3.5 69 to 241
2 to 5 0.14 to 0.34 GE27213X012 Orange Stripe 1.75 to 5.5 121 to 379
5 to 10 0.34 to 0.69 GE39890X012 Black Stripe 2.5 to 6.75 172 to 465
1. Outlet pressure range is controlled by 67CP Series pressure loading regulator spring. Only the 1 to 2, 2 to 5, and 5 to 10 psig / 0.07 to 0.14; 0.14 to 0.34; and 0.34 to 0.69 bar
spring ranges are available with Token Relief.
Table 5. Token Relief Valve Start-to-Discharge Pressure Above Setpoint
For subcritical fl ow:
If pressure drops are lower than critical (absolute
outlet pressure greater than approximately one-half
the absolute inlet pressure), use the following formula
and convert according to the factors in the preceding
paragraph if necessary:
520
GT
3417
C1
P
P1
CgP1SIN DEG
P
Q =
where:
C1= Cg/Cv (see Table 3)
Cg=Gas sizing coef cient (see Table 3)
G = Gas speci c gravity (air = 1.0)
P1=Regulator inlet pressure, psia
ΔP =Pressure drop across regulator, psig
Q = Gas ow rate, SCFH
T = Absolute temperature of gas at inlet, °Rankine
Bulletin 71.1:CP200
9
Table 6. CP200 Series Flow Capacities for 1 psig / 69 mbar Setpoint
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Sizes: 3/4 and 1 NPT
3 0.21 160 4.2 310 8.3 460 12.3 850 22.8 1300 34.8
50.34 210 5.6 440 11.8 760 20.4 1200 32.2 1500 40.2
10 0.69 320 8.5 730 19.5 1100 29.5 2100 56.3 2100 56.3
15 1.0 410 11.0 890 23.8 1500 40.2 2500 67.1 2500 67.1
20 1.4 490 13.1 1000 26.8 1800 48.3 2800 75.1 2700 72.4
30 2.1 630 16.9 1400 37.5 2400 64.4 3000 80.5 2800 75.1
40 2.8 740 19.8 1700 45.6 2800 75.1 3000 80.5
50 3.4 920 24.6 2000 53.6 3100 83.2 3100 83.2
60 4.1 1000 26.8 2300 61.7 3300 88.5 3100 83.2
80 5.5 1300 34.8 3000 80.5 3300 88.5
100 6.9 1600 42.9 3100 83.2 3300 88.5
125 8.6 2000 53.6 3100 83.2 1300 34.8
psig bar Body Size: 1-1/4 NPT
3 0.21 160 4.2 310 8.3 460 12.3 850 22.8 1400 37.5
50.34 210 5.6 440 11.8 800 21.4 1600 42.9 2100 56.3
10 0.69 320 8.5 730 19.5 1300 34.8 2500 67.1 2800 75.1
15 1.0 410 11.0 890 23.8 1600 42.9 3000 80.5 3000 80.5
20 1.4 490 13.1 1000 26.8 1900 51.0 3000 80.5 3000 80.5
30 2.1 630 16.9 1400 37.5 2500 67.1 3000 80.5 3000 80.5
40 2.8 740 19.8 1700 45.6 3000 80.5 3000 80.5
50 3.4 920 24.6 2000 53.6 3200 85.9 3200 85.9
60 4.1 1000 26.8 2300 61.7 3200 85.9 3200 85.9
80 5.5 1300 34.8 3000 80.5 4200 113
100 6.9 1600 42.9 3300 88.5 4200 113
125 8.6 2000 53.6 3300 88.5 4200 113
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Shaded areas indicate values that are limited due to boost effects.
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
1 psig -0.16 psi 0.16 psi 1 to 2 psig GE30199X012 /
Yellow Stripe
69 mbar -11 mbar 11 mbar 69 mbar to 0.14 bar
Bulletin 71.1:CP200
10
Table 7. CP200 Series Flow Capacities for 2 psig / 0.14 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
2 psig -0.17 psi 0.17 psi 1 to 2 psig GE30199X012 /
Yellow Stripe
0.14 bar -12 mbar 12 mbar 69 mbar to 0.14 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Sizes: 3/4 and 1 NPT
50.34 190 5.1 410 11.0 780 20.9 1400 37.5 1900 51.0
10 0.69 330 8.8 580 15.5 1200 32.2 2600 69.7 2900 77.8
15 1.0 420 11.2 770 20.6 1600 42.9 3200 85.9 3200 85.9
20 1.4 500 13.4 1000 26.8 1900 51.0 3200 85.9 3200 85.9
30 2.1 630 16.9 1300 34.8 2500 67.1 3200 85.9 3200 85.9
40 2.8 790 21.2 1600 42.9 3100 83.2 4200 113
50 3.4 930 24.9 1800 48.3 3700 99.3 4200 113
60 4.1 1000 26.8 1800 48.3 4200 113 4200 113
80 5.5 1300 34.8 1800 48.3 4200 113
100 6.9 1600 42.9 1800 48.3 4200 113
125 8.6 1800 48.3 1800 48.3
psig bar Body Size: 1-1/4 NPT
50.34 190 5.1 420 11.2 780 20.9 1400 37.5 1900 51.0
10 0.69 330 8.8 580 15.5 1200 32.2 2600 69.7 2900 77.8
15 1.0 420 11.2 770 20.6 1600 42.9 3200 85.9 3200 85.9
20 1.4 500 13.4 1000 26.8 1900 51.0 3200 85.9 3200 85.9
30 2.1 630 16.9 1300 34.8 2500 67.1 3200 85.9 3200 85.9
40 2.8 790 21.2 1600 42.9 3100 83.2 4200 113
50 3.4 930 24.9 1800 48.3 3700 99.3 4200 113
60 4.1 1000 26.8 1800 48.3 4200 113 4200 113
80 5.5 1300 34.8 1800 48.3 4200 113
100 6.9 1600 42.9 1800 48.3 4200 113
125 8.6 1800 48.3 1800 48.3
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
11
Table 8. CP200 Series Flow Capacities for 5 psig / 0.34 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
5 psig -0.2 psi 0.2 psi 2 to 5 psig GE27213X012 /
Orange Stripe
0.34 bar -14 mbar 14 mbar 0.14 to 0.34 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Sizes: 3/4 and 1 NPT
10 0.69 270 7.2 560 15.0 960 25.7 2000 53.6 2900 77.8
15 1.0 370 9.9 870 23.3 1500 40.2 3100 83.2 3800 102
20 1.4 470 12.6 1000 26.8 1900 51.0 3900 105 3900 105
30 2.1 620 16.6 1400 37.5 2400 64.4 4300 115 4300 115
40 2.8 770 20.6 1700 45.6 3000 80.5 4300 115
50 3.4 940 25.2 1900 51.0 3600 96.6 4300 115
60 4.1 1000 26.8 2000 53.6 4300 115 4300 115
80 5.5 1300 34.8 2000 53.6 4300 115
100 6.9 1600 42.9 2000 53.6 4300 115
125 8.6 2000 53.6 2000 53.6
psig bar Body Size: 1-1/4 NPT
10 0.69 270 7.2 560 15.0 1000 26.8 2000 53.6 3000 80.5
15 1.0 370 9.9 870 23.3 1500 40.2 3200 85.9 3800 102
20 1.4 470 12.6 1000 26.8 1900 51.0 4000 107 3900 105
30 2.1 620 16.6 1400 37.5 2600 69.7 4300 115 4300 115
40 2.8 770 20.6 1700 45.6 3000 80.5 5300 142
50 3.4 940 25.2 1900 51.0 3700 99.3 5300 142
60 4.1 1000 26.8 2000 53.6 4300 115 5300 142
80 5.5 1300 34.8 2000 53.6 4300 115
100 6.9 1600 42.9 2000 53.6 4300 115
125 8.6 2000 53.6 2000 53.6
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
12
Table 9. CP200 Series Flow Capacities for 10 psig / 0.69 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
10 psig -0.25 psi 0.25 psi 5 to 10 psig GE39890X012 /
Black Stripe
0.69 bar -17 mbar 17 mbar 0.34 to 0.69 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Sizes: 3/4 and 1 NPT
15 1.0 260 6.9 580 15.5 1000 26.8 1600 42.9 2500 67.1
20 1.4 410 11.0 880 23.6 1500 40.2 2900 77.8 3100 83.2
30 2.1 590 15.8 1200 32.2 2200 59.0 3800 102 4100 110
40 2.8 760 20.4 1500 40.2 2900 77.8 4200 113
50 3.4 900 24.1 1900 51.0 3600 96.6 4700 126
60 4.1 990 26.5 2300 61.7 4000 107 4700 126
80 5.5 1300 34.8 2900 77.8 5200 139
100 6.9 1600 42.9 3500 93.9 5200 139
125 8.6 1900 51.0 4500 121 5200 139
psig bar Body Size: 1-1/4 NPT
15 1.0 260 6.9 580 15.5 1000 26.8 2500 67.1 3400 91.2
20 1.4 410 11.0 880 23.6 1700 45.6 3200 85.9 4400 118
30 2.1 590 15.8 1200 32.2 2200 59.0 5000 134 5000 134
40 2.8 760 20.4 1500 40.2 3100 83.2 6100 164
50 3.4 900 24.1 1900 51.0 3700 99.3 6900 185
60 4.1 990 26.5 2300 61.7 4300 115 8000 215
80 5.5 1300 34.8 2900 77.8 5200 139
100 6.9 1600 42.9 3500 93.9 5200 139
125 8.6 1900 51.0 4500 121 5200 139
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
13
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
15 psig -0.3 psi 0.3 psi 10 to 20 psig GE30200X012 /
Purple Stripe
1.0 bar -20 mbar 20 mbar 0.69 to 1.4 bar
Table 10. CP200 Series Flow Capacities for 15 psig / 1.0 bar Setpoint
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Sizes: 3/4 and 1 NPT
20 1.4 360 9.6 460 12.3 1200 32.2 2300 61.7 2800 75.1
30 2.1 580 15.5 1200 32.2 2200 59.0 4000 107 4200 113
40 2.8 690 18.5 1600 42.9 2900 77.8 4900 131
50 3.4 890 23.8 2000 53.6 3500 93.9 5100 137
60 4.1 1000 26.8 2300 61.7 4000 107 5900 158
80 5.5 1300 34.8 2900 77.8 5100 137
100 6.9 1500 40.2 3600 96.6 6200 166
125 8.6 1800 48.3 4400 118 7500 201
psig bar Body Size: 1-1/4 NPT
20 1.4 360 9.6 460 12.3 1200 32.2 2700 72.4 4100 110
30 2.1 580 15.5 1200 32.2 2200 59.0 4900 131 6000 161
40 2.8 690 18.5 1600 42.9 2900 77.8 6300 169
50 3.4 890 23.8 2000 53.6 3500 93.9 7500 201
60 4.1 1000 26.8 2300 61.7 4000 107 8200 220
80 5.5 1300 34.8 2900 77.8 5100 137
100 6.9 1500 40.2 3600 96.6 6200 166
125 8.6 1800 48.3 4400 118 7500 201
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Table 11. CP200 Series Flow Capacities for 20 psig / 1.4 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
20 psig -0.35 psi 0.35 psi 10 to 20 psig GE30200X012 /
Purple Stripe
1.4 bar -24 mbar 24 mbar 0.69 to 1.4 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Sizes: 3/4 and 1 NPT
30 2.1 560 15.0 1100 29.5 1900 51.0 3800 102 4100 110
40 2.8 740 19.8 1600 42.9 2700 72.4 4800 129
50 3.4 840 22.5 1900 51.0 3300 88.5 5900 158
60 4.1 1000 26.8 2300 61.7 4000 107 6700 180
80 5.5 1300 34.8 2900 77.8 5200 139
100 6.9 1600 42.9 3600 96.6 6300 169
125 8.6 2000 53.6 4400 118 7700 207
psig bar Body Size: 1-1/4 NPT
30 2.1 560 15.0 1100 29.5 1900 51.0 4100 110 5600 150
40 2.8 740 19.8 1600 42.9 2700 72.4 6400 172
50 3.4 840 22.5 1900 51.0 3300 88.5 7300 196
60 4.1 1000 26.8 2300 61.7 4000 107 8800 236
80 5.5 1300 34.8 2900 77.8 5200 139
100 6.9 1600 42.9 3600 96.6 6300 169
125 8.6 2000 53.6 4400 118 7700 207
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
14
Table 12. CP205 and CP206 Series Flow Capacities for 1 psig / 69 mbar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
1 psig -0.16 psi 0.16 psi 1 to 2 psig GE30199X012 /
Yellow Stripe
69 mbar -11 mbar 11 mbar 69 mbar to 0.14 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 5/16 / 7.9
SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h
psig bar Body Size: 3/4 NPT
3 0.21 155 4.2 295 7.9 420 11.3 570 15.3
50.34 200 5.4 460 12.3 670 18.0 775 20.8
10 0.69 345 9.2 780 20.9 1100 29.5 1240 33.2
15 1.0 425 11.4 1000 26.8 1390 37.3 1540 41.3
20 1.4 525 14.1 1140 30.6 1610 43.2 1780 47.7
30 2.1 710 19.0 1500 40.2 1860 49.9 1960 52.5
40 2.8 875 23.5 1890 50.7 1980 53.1 1930 51.7
50 3.4 1010 27.1 2010 53.9 1960 52.5 1960 52.5
60 4.1 1180 31.6 2000 53.6 1970 52.8 2040 54.7
80 5.5 1450 38.9 2070 55.5 1990 53.4 2290 61.4
90 6.2 1630 43.7 2210 59.2 2170 58.2 2390 64.1
100 6.9 1810 48.5 1130 30.3 2340 62.7 2440 65.4
125 8.6 1060 28.4 1130 30.3 2670 71.6 2440 65.4
psig bar Body Size: 1 NPT
3 0.21 165 4.4 345 9.2 480 12.9 480 12.9
50.34 230 6.2 490 13.1 685 18.4 695 18.6
10 0.69 355 9.5 765 20.5 1020 27.3 1160 31.1
15 1.0 470 12.6 995 26.7 1240 33.2 1360 36.5
20 1.4 560 15.0 1190 31.9 1400 37.5 1520 40.8
30 2.1 735 19.7 1530 41.0 1620 43.4 1740 46.6
40 2.8 905 24.3 1810 48.5 1820 48.8 1800 48.3
50 3.4 1060 28.4 1970 52.8 1980 53.1 1970 52.8
60 4.1 1250 33.5 1990 53.4 2030 54.4 2040 54.7
80 5.5 1580 42.4 2210 59.2 2340 62.7 2720 72.9
90 6.2 1730 46.4 2400 64.3 2510 67.3 2720 72.9
100 6.9 1930 51.7 1290 34.6 2730 73.2 2870 76.9
125 8.6 1400 37.5 1290 34.6 2760 74.0 2870 76.9
psig bar Body Size: 1-1/4 NPT
3 0.21 175 4.7 280 7.5 395 10.6 460 12.3
50.34 185 5.0 435 11.7 585 15.7 720 19.3
10 0.69 355 9.5 720 19.3 875 23.5 1120 30.0
15 1.0 390 10.5 1010 27.1 1190 31.9 1310 35.1
20 1.4 520 13.9 1180 31.6 1440 38.6 1370 36.7
30 2.1 725 19.4 1420 38.1 1440 38.6 1460 39.1
40 2.8 810 21.7 1840 49.3 1570 42.1 1720 46.1
50 3.4 955 25.6 1850 49.6 1570 42.1 1730 46.4
60 4.1 965 25.9 1950 52.3 1640 44.0 1830 49.1
80 5.5 1370 36.7 2000 53.6 2020 54.2 2240 60.1
90 6.2 1610 43.2 2000 53.6 2130 57.1 2430 65.1
100 6.9 1720 46.1 1400 37.5 2270 60.9 2720 72.9
125 8.6 1750 46.9 1400 37.5 2690 72.1 3040 81.5
Shaded areas indicate values that are limited due to boost effects.
Bulletin 71.1:CP200
15
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
18 / 3.2 3/16 / 4.8 1/4 / 6.4 5/16 / 7.9
SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h
psig bar Body Size: 3/4 NPT
50.34 180 4.8 390 10.5 570 15.3 715 19.2
10 0.69 290 7.8 750 20.1 1070 28.7 1220 32.7
15 1.0 430 11.5 945 25.3 1420 38.1 1500 40.2
20 1.4 525 14.1 1120 30.0 1680 45.0 1860 49.9
30 2.1 670 18.0 1560 41.8 2010 53.9 2090 56.0
40 2.8 820 22.0 1900 50.9 2140 57.4 2110 56.6
50 3.4 950 25.5 2080 55.8 2140 57.4 2190 58.7
60 4.1 1130 30.3 2240 60.1 2270 60.9 2290 61.4
80 5.5 1470 39.4 2320 62.2 2290 61.4 2330 62.5
90 6.2 1630 43.7 2310 61.9 2320 62.2 2410 64.6
100 6.9 1730 46.4 1280 34.3 2420 64.9 2530 67.8
125 8.6 2070 55.5 1280 34.3 2690 72.1 2730 73.2
psig bar Body Size: 1 NPT
50.34 160 4.3 380 10.2 540 14.5 545 14.6
10 0.69 355 9.5 765 20.5 900 24.1 985 26.4
15 1.0 475 12.7 985 26.4 1360 36.5 1350 36.2
20 1.4 555 14.9 1150 30.8 1450 38.9 1510 40.5
30 2.1 730 19.6 1490 39.9 1820 48.8 1720 46.1
40 2.8 905 24.3 1850 49.6 1810 48.5 1880 50.4
50 3.4 1050 28.2 1920 51.5 2010 53.9 2010 53.9
60 4.1 1210 32.4 2090 56.0 2100 56.3 2160 57.9
80 5.5 1460 39.1 2290 61.4 2530 67.8 2560 68.6
90 6.2 1710 45.8 2400 64.3 2660 71.3 2740 73.5
100 6.9 1940 52.0 2220 59.5 2860 76.7 2860 76.7
125 8.6 2320 62.2 2020 54.2 2860 76.7 2970 79.6
psig bar Body Size: 1-1/4 NPT
50.34 135 3.6 275 7.4 485 13.0 570 15.3
10 0.69 270 7.2 595 16.0 1030 27.6 1200 32.2
15 1.0 355 9.5 945 25.3 1400 37.5 1980 53.1
20 1.4 420 11.3 1090 29.2 1930 51.7 2560 68.6
30 2.1 610 16.4 1570 42.1 2670 71.6 3580 96.0
40 2.8 820 22.0 1930 51.7 3370 90.3 4590 123
50 3.4 980 26.3 2270 60.9 4040 108 5500 147
60 4.1 1160 31.1 2680 71.8 4750 127 6400 172
80 5.5 1490 39.9 3430 92.0 3220 86.3 7830 210
90 6.2 1600 42.9 3850 103 3070 82.3 2620 70.2
100 6.9 1820 48.8 4230 113 3070 82.3 2620 70.2
125 8.6 2270 60.9 2130 57.1 3070 82.3 2620 70.2
Shaded areas indicate values that are limited due to boost effects.
Table 13. CP205 and CP206 Series Flow Capacities for 2 psig / 0.14 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
2 psig -0.17 psi 0.17 psi 1 to 2 psig GE30199X012 /
Yellow Stripe
0.14 bar -12 mbar 12 mbar 69 mbar to 0.14 bar
Bulletin 71.1:CP200
16
Table 14. CP205 and CP206 Series Flow Capacities for 5 psig / 0.34 bar Setpoint
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 5/16 / 7.9
SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h
psig bar Body Size: 3/4 NPT
10 0.69 230 6.2 535 14.3 855 22.9 870 23.3
15 1.0 405 10.9 890 23.9 1390 37.3 1620 43.4
20 1.4 525 14.1 990 26.5 1680 45.0 1860 49.9
30 2.1 705 18.9 1530 41.0 2380 63.8 2590 69.4
40 2.8 870 23.3 1960 52.5 2640 70.8 2660 71.3
50 3.4 1010 27.1 2200 59.0 2810 75.3 2880 77.2
60 4.1 1180 31.6 2520 67.6 2810 75.3 2880 77.2
80 5.5 1510 40.5 2940 78.8 2810 75.3 2880 77.2
90 6.2 1700 45.6 2950 79.1 2810 75.3 2880 77.2
100 6.9 1860 49.9 2970 79.6 2810 75.3 2880 77.2
125 8.6 2280 61.1 1590 42.6 2810 75.3 2880 77.2
psig bar Body Size: 1 NPT
10 0.69 320 8.6 630 16.9 750 20.1 915 24.5
15 1.0 405 10.9 930 24.9 1360 36.5 1400 37.5
20 1.4 550 14.7 1170 31.4 1650 44.2 1790 48.0
30 2.1 725 19.4 1550 41.6 2090 56.0 2060 55.2
40 2.8 905 24.3 1900 50.9 2240 60.1 2090 56.0
50 3.4 1050 28.2 2020 54.2 2330 62.5 2440 65.4
60 4.1 1230 33.0 2520 67.6 2470 66.2 2490 66.8
80 5.5 1530 41.0 2800 75.1 2940 78.8 2730 73.2
90 6.2 1690 45.3 2800 75.1 3190 85.5 2910 78.0
100 6.9 1840 49.3 2740 73.5 3340 89.5 2990 80.2
125 8.6 2240 60.1 1770 47.5 3820 102 3420 91.7
psig bar Body Size: 1-1/4 NPT
10 0.69 215 5.8 440 11.8 845 22.7 930 24.9
15 1.0 350 9.4 835 22.4 1340 35.9 1540 41.3
20 1.4 465 12.5 1100 29.5 1780 47.7 2380 63.8
30 2.1 675 18.1 1510 40.5 2650 71.0 3400 91.2
40 2.8 740 19.8 1860 49.9 3360 90.1 4640 124
50 3.4 930 24.9 2180 58.4 4090 110 5580 150
60 4.1 1150 30.8 2150 57.6 4640 124 3130 83.9
80 5.5 1400 37.5 2470 66.2 4150 111 2620 70.2
90 6.2 1570 42.1 2540 68.1 3640 97.6 2620 70.2
100 6.9 1730 46.4 2560 68.6 3120 83.6 2620 70.2
125 8.6 2030 54.4 1780 47.7 2990 80.2 1360 36.5
Shaded areas indicate values that are limited due to boost effects.
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
5 psig -0.2 psi 0.2 psi 2 to 5 psig GE27213X012 /
Orange Stripe
0.34 bar -14 mbar 14 mbar 0.14 to 0.34 bar
Bulletin 71.1:CP200
17
Table 15. CP205 and CP206 Series Flow Capacities for 10 psig / 0.69 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
10 psig -0.25 psi 0.25 psi 5 to 10 psig GE39890X012 /
Black Stripe
0.69 bar -17 mbar 17 mbar 0.34 to 0.69 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 5/16 / 7.9
SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h SCFH Nm³/h
psig bar Body Size: 3/4 NPT
15 1.0 270 7.2 730 19.6 1030 27.6 1180 31.6
20 1.4 415 11.1 995 26.7 1500 40.2 1660 44.5
30 2.1 515 13.8 1530 41.0 2190 58.7 2530 67.8
40 2.8 765 20.5 1860 49.9 2900 77.7 2860 76.7
50 3.4 915 24.5 2230 59.8 3050 81.8 3130 83.9
60 4.1 1120 30.0 2360 63.3 3280 87.9 3290 88.2
80 5.5 1460 39.1 2920 78.3 3330 89.3 3490 93.6
90 6.2 1610 43.2 3570 95.7 3520 94.4 3490 93.6
100 6.9 1620 43.4 3710 99.5 3370 90.3 3490 93.6
125 8.6 2050 55.0 3870 104 3370 90.3 3490 93.6
psig bar Body Size: 1 NPT
15 1.0 215 5.8 660 17.7 1050 28.2 870 23.3
20 1.4 370 9.9 830 22.3 1490 39.9 1790 48.0
30 2.1 600 16.1 1310 35.1 2000 53.6 2470 66.2
40 2.8 775 20.8 1740 46.6 2420 64.9 2770 74.3
50 3.4 965 25.9 2140 57.4 2590 69.4 2920 78.3
60 4.1 1110 29.8 2530 67.8 2800 75.1 2920 78.3
80 5.5 1430 38.3 3020 81.0 3150 84.5 3400 91.2
90 6.2 1610 43.2 3520 94.4 3510 94.1 3590 96.2
100 6.9 1750 46.9 3590 96.2 3800 110 4060 109
125 8.6 2240 60.1 3700 99.2 3940 106 4330 116
psig bar Body Size: 1-1/4 NPT
15 1.0 260 7.0 625 16.8 1150 30.8 1170 31.4
20 1.4 380 10.2 1000 26.8 1590 42.6 1700 45.6
30 2.1 635 17.0 1280 34.3 2210 59.2 2610 70.0
40 2.8 800 21.4 1690 45.3 2700 72.4 3290 88.2
50 3.4 935 25.1 2250 60.3 3390 90.9 3840 103
60 4.1 1070 28.7 2490 66.8 3850 103 3890 104
80 5.5 1480 39.7 3220 86.3 4180 112 4750 127
90 6.2 1630 43.7 3370 90.3 4780 128 5000 134
100 6.9 1700 45.6 4090 110 5400 145 5000 134
125 8.6 2210 59.2 4420 118 5400 145 5000 134
Shaded areas indicate values that are limited due to boost effects.
Bulletin 71.1:CP200
18
Table 16. CP205 and CP206 Series Flow Capacities for 15 psig / 1.0 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
15 psig -0.3 psi 0.3 psi 10 to 20 psig GE30200X012 /
Purple Stripe
1.0 bar -20 mbar 20 mbar 0.69 to 1.4 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 5/16 / 7.9
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
20 1.4 355 9.5 775 20.8 1280 34.3 1380 37.0
30 2.1 680 18.2 1330 35.7 1970 52.8 2640 70.8
40 2.8 725 19.4 1920 51.5 2610 70.0 3200 85.8
50 3.4 1010 27.1 2260 60.6 3530 94.6 3830 103
60 4.1 1230 33.0 2570 68.9 3870 104 3930 105
80 5.5 1480 39.7 3290 88.2 4410 118 4990 134
90 6.2 1660 44.5 3690 98.9 4800 129 5070 136
100 6.9 1820 48.8 4040 108 4800 129 5200 139
125 8.6 2390 64.1 4600 123 4800 129 5200 139
psig bar Body Size: 1 NPT
20 1.4 290 7.8 660 17.7 1280 34.3 1490 39.9
30 2.1 655 17.6 1590 42.6 2160 57.9 2610 70.0
40 2.8 790 21.2 2000 53.6 2910 78.0 3140 84.2
50 3.4 1070 28.7 2370 63.5 3260 87.4 3450 92.5
60 4.1 1170 31.4 2600 69.7 3680 98.7 3700 99.2
80 5.5 1320 35.4 3480 93.3 4050 109 4010 107
90 6.2 1640 44.0 3690 98.9 4080 109 4010 107
100 6.9 1790 48.0 3990 107 4440 119 4130 111
125 8.6 2300 61.7 4520 121 4470 120 5250 141
psig bar Body Size: 1-1/4 NPT
20 1.4 190 5.1 580 15.5 1010 27.1 930 24.9
30 2.1 465 12.5 1300 34.9 2200 59.0 2720 72.9
40 2.8 730 19.6 1770 47.5 3160 84.7 4050 109
50 3.4 870 23.3 1930 51.7 3740 100 5050 135
60 4.1 1050 28.2 2620 70.2 4380 117 5860 157
80 5.5 1220 32.7 3250 87.1 5980 160 7980 214
90 6.2 1650 44.2 3500 93.8 6610 177 8540 229
100 6.9 1710 45.8 3810 102 7220 194 9730 261
125 8.6 2210 59.2 5100 137 4030 108 7370 198
Shaded areas indicate values that are limited due to boost effects.
Bulletin 71.1:CP200
19
Table 17. CP205 and CP206 Series Flow Capacities for 20 psig / 1.4 bar Setpoint
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
20 psig -0.35 psi 0.35 psi 10 to 20 psig GE30200X012 /
Purple Stripe
1.4 bar -24 mbar 24 mbar 0.69 to 1.4 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
1/8 / 3.2 3/16 / 4.8 1/4 / 6.4 5/16 / 7.9
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
30 2.1 550 14.7 1240 33.2 1890 50.7 2080 55.8
40 2.8 795 21.3 1540 41.3 2730 73.2 3160 84.7
50 3.4 935 25.1 2160 57.9 3610 96.8 3710 99.5
60 4.1 1080 29.0 2530 67.8 4180 112 4050 109
80 5.5 1460 39.1 3240 86.9 4750 127 4820 129
90 6.2 1580 42.4 3670 98.4 5300 142 4870 131
100 6.9 1770 47.5 3950 106 5500 147 5130 137
125 8.6 2260 60.6 4710 126 5650 151 5190 139
psig bar Body Size: 1 NPT
30 2.1 570 15.3 1380 37.0 1920 51.5 2190 58.7
40 2.8 835 22.4 1900 50.9 2700 72.4 3140 84.2
50 3.4 1030 27.6 2340 62.7 3340 89.5 3990 107
60 4.1 1230 33.0 2590 69.4 3500 93.8 4130 111
80 5.5 1560 41.8 3390 90.9 4140 111 4290 115
90 6.2 1700 45.6 3710 99.5 4340 116 4640 124
100 6.9 1890 50.7 4120 110 4520 121 5030 135
125 8.6 2250 60.3 4770 128 4850 130 5710 153
psig bar Body Size: 1-1/4 NPT
30 2.1 515 13.8 1030 27.6 1810 48.5 2360 63.3
40 2.8 795 21.3 1660 44.5 2850 76.4 3700 99.2
50 3.4 925 24.8 1750 46.9 4020 108 4960 133
60 4.1 1160 31.1 2470 66.2 4510 121 6120 164
80 5.5 1380 37.0 3310 88.7 5770 155 7870 211
90 6.2 1650 44.2 3660 98.1 6580 176 9070 243
100 6.9 1790 48.0 4020 108 7220 194 9860 264
125 8.6 2270 60.9 5110 137 8610 231 9860 264
Bulletin 71.1:CP200
20
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
2 psig -0.17 psi 0.17 psi 1 to 2 psig GE30199X012 /
Yellow Stripe
0.14 bar -12 mbar 12 mbar 0.07 to 0.14 bar
Table 18. CP200 Series Internal Registration Flow Capacities for 2 psig / 0.14 bar Setpoint
with 1% ABS Pressure Factor Accuracy (PFM Approved)
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
10 0.69 580 15.5 1100 29.5 2000 53.6 2900 77.7
15 1.0 770 20.6 1500 40.2 2500 67.0 3200 85.8
20 1.4 970 26.0 1800 48.2 2800 75.0 3200 85.8
25 1.7 1100 29.5 2100 56.3 3000 80.4 3200 85.8
30 2.1 1300 34.8 2300 61.6 3100 83.1 3200 85.8
40 2.8 1600 42.9 2900 77.7 3100 83.1
50 3.4 1800 48.2 3300 88.4 3100 83.1
60 4.1 1800 48.2 3400 91.1 2600 69.7
80 5.5 1800 48.2 3500 93.8
100 6.9 1800 48.2
125 8.6
psig bar Body Size: 1 NPT
10 0.69 580 15.5 1200 32.2 1800 48.2 2500 67.0
15 1.0 770 20.6 1500 40.2 2800 75.0 3200 85.8
20 1.4 1000 26.8 1900 50.9 2900 77.7 3200 85.8
25 1.7 1200 32.2 2200 59.0 3200 85.8 3200 85.8
30 2.1 1300 34.8 2500 67.0 3200 85.8 3200 85.8
40 2.8 1600 42.9 3100 83.1 4200 113
50 3.4 1800 48.2 3700 99.2 4200 113
60 4.1 1800 48.2 3900 105 4200 113
80 5.5 1800 48.2 3900 105
100 6.9 3900 105
125 8.6
psig bar Body Size: 1-1/4 NPT
10 0.69 580 15.5 1100 29.5 2400 64.3 2900 77.7
15 1.0 770 20.6 1600 42.9 3200 85.8 3200 85.8
20 1.4 1000 26.8 1900 50.9 3200 85.8 3200 85.8
25 1.7 1200 32.2 2200 59.0 3200 85.8 3200 85.8
30 2.1 1300 34.8 2400 64.3 3200 85.8 3200 85.8
40 2.8 1600 42.9 3000 80.4 4200 113
50 3.4 1800 48.2 3700 99.2 4200 113
60 4.1 1800 48.2 4200 113 4200 113
80 5.5 1800 48.2
100 6.9
125 8.6
Shaded areas indicate values that are limited due to boost effects.
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
21
Table 19. CP200 Series Internal Registration Flow Capacities for 5 psig / 0.34 bar Setpoint
with 1% ABS Pressure Factor Accuracy (PFM Approved)
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
5 psig -0.20 psi 0.20 psi 2 to 5 psig GE27213X012 /
Orange Stripe
0.34 bar -14 mbar 14 mbar 0.14 to 0.34 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
10 0.69 560 15.0 960 25.7 2000 53.6 2900 77.7
15 1.0 840 22.5 1500 40.2 3100 83.1 3800 102
20 1.4 1000 26.8 1900 50.9 3900 105 3900 105
25 1.7 1200 32.2 2300 61.6 4300 115 4300 115
30 2.1 1300 34.8 2400 64.3 4300 115 4300 115
40 2.8 1600 42.9 3000 80.4 4300 115
50 3.4 1900 50.9 3500 93.8 4300 115
60 4.1 2000 53.6 3500 93.8 4300 115
80 5.5 2000 53.6 4100 110
100 6.9 2000 53.6 3400 91.1
125 8.6 2000 53.6
psig bar Body Size: 1 NPT
10 0.69 560 15.0 940 25.2 1300 34.8 1800 48.2
15 1.0 830 22.2 1500 40.2 2900 77.7 3600 96.5
20 1.4 980 26.3 1900 50.9 3900 105 3900 105
25 1.7 1200 32.2 2300 61.6 3900 105 4300 115
30 2.1 1200 32.2 2400 64.3 4300 115 4300 115
40 2.8 1600 42.9 3000 80.4 4300 115
50 3.4 1900 50.9 3600 96.5 4300 115
60 4.1 2000 53.6 4300 115 4300 115
80 5.5 2000 53.6 4300 115
100 6.9 2000 53.6
125 8.6
psig bar Body Size: 1-1/4 NPT
10 0.69 560 15.0 440 11.8 2000 53.6 3000 80.4
15 1.0 830 22.2 1400 37.5 3200 85.8 3800 102
20 1.4 1000 26.8 1700 45.6 4000 107 3900 105
25 1.7 1200 32.2 1900 50.9 4600 123 4300 115
30 2.1 1300 34.8 2400 64.3 4300 115 4300 115
40 2.8 1700 45.6 2800 75.0 5200 139
50 3.4 1900 50.9 3400 91.1 5000 134
60 4.1 2000 53.6 3900 105 3900 105
80 5.5 2000 53.6 4000 107
100 6.9 2000 53.6
125 8.6 2000 53.6
Shaded areas indicate values that are limited due to boost effects.
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
22
Table 20. CP200 Series Internal Registration Flow Capacities for 7 psig / 0.48 bar Setpoint
with 1% ABS Pressure Factor Accuracy (PFM Approved)
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
7 psig -0.22 psi 0.22 psi 5 to 10 psig GE39890X012 /
Black Stripe
0.48 bar -15 mbar 15 mbar 0.34 to 0.69 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
10 0.69 140 3.8
15 1.0 740 19.8 1100 29.5 1900 50.9 1900 50.9
20 1.4 1000 26.8 1700 45.6 2900 77.7 2700 72.4
25 1.7 1100 29.5 2100 56.3 3300 88.4 3500 93.8
30 2.1 1300 34.8 2300 61.6 3700 99.2 3600 96.5
40 2.8 1600 42.9 2900 77.7 4200 113
50 3.4 1900 50.9 3400 91.1 4500 121
60 4.1 2200 59.0 3700 99.2 4600 123
80 5.5 2900 77.7 4000 107
100 6.9 3400 91.1 3200 85.8
125 8.6 3900 105
psig bar Body Size: 1 NPT
10 0.69 240 6.4 600 16.1 650 17.4
15 1.0 580 15.5 1500 40.2 2100 56.3 3200 85.8
20 1.4 970 26.0 1900 50.9 3500 93.8 4700 126
25 1.7 1100 29.5 2300 61.6 4200 113 4800 129
30 2.1 1300 34.8 2600 69.7 5000 134 5500 147
40 2.8 1600 42.9 3200 85.8 6100 163
50 3.4 2000 53.6 3800 102 6700 180
60 4.1 2200 59.0 4400 118 7700 206
80 5.5 2900 77.7 5400 145
100 6.9 3200 85.8 6600 177
125 8.6
psig bar Body Size: 1-1/4 NPT
10 0.69 380 10.2
15 1.0 770 20.6 980 26.3 1900 50.9 2100 56.3
20 1.4 980 26.3 1600 42.9 3400 91.1 4100 110
25 1.7 1100 29.5 2100 56.3 3700 99.2 4600 123
30 2.1 1300 34.8 2300 61.6 3900 105 4600 123
40 2.8 1600 42.9 2900 77.7 4800 129
50 3.4 2000 53.6 3500 93.8 4000 107
60 4.1 2300 61.6 3900 105 3500 93.8
80 5.5 3000 80.4 3900 105
100 6.9 3500 93.8 3900 105
125 8.6 4300 115
Shaded areas indicate values that are limited due to boost effects.
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
23
Table 21. CP200 Series Internal Registration Flow Capacities for 10 psig / 0.69 bar Setpoint
with 1% ABS Pressure Factor Accuracy (PFM Approved)
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
10 psig -0.25 psi 0.25 psi 5 to 10 psig GE39890X012 /
Black Stripe
0.69 bar -17 mbar 17 mbar 0.34 to 0.69 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
15 1.0 570 15.3 1000 26.8 1100 29.5 1300 34.8
20 1.4 880 23.6 1500 40.2 2800 75.0 3100 83.1
25 1.7 1100 29.5 2200 59.0 3500 93.8 3800 102
30 2.1 1200 32.2 2200 59.0 3800 102 4100 110
40 2.8 1500 40.2 2900 77.7 4200 113
50 3.4 1900 50.9 3600 96.5 4700 126
60 4.1 2300 61.6 4000 107 4700 126
80 5.5 2900 77.7 4100 110
100 6.9 3500 93.8 4100 110
125 8.6 4300 115 4100 110
psig bar Body Size: 1 NPT
15 1.0 580 15.5 1000 26.8 1600 42.9 2200 59.0
20 1.4 880 23.6 1500 40.2 2900 77.7 3100 83.1
25 1.7 1200 32.2 2100 56.3 3800 102 4100 110
30 2.1 1200 32.2 2200 59.0 3800 102 4100 110
40 2.8 1500 40.2 2900 77.7 4200 113
50 3.4 1900 50.9 3600 96.5 4700 126
60 4.1 2300 61.6 4000 107 4700 126
80 5.5 2900 77.7 5200 139
100 6.9 3500 93.8 5200 139
125 8.6 4200 113 5200 139
psig bar Body Size: 1-1/4 NPT
15 1.0 510 13.7 1000 26.8 2100 56.3 2800 75.0
20 1.4 880 23.6 1600 42.9 3200 85.8 4400 118
25 1.7 1100 29.5 2200 59.0 4500 121 5000 134
30 2.1 1200 32.2 2200 59.0 5000 134 5000 134
40 2.8 1500 40.2 3100 83.1 6100 163
50 3.4 1900 50.9 3700 99.2 6900 185
60 4.1 2300 61.6 4300 115 7000 188
80 5.5 2900 77.7 5200 139
100 6.9 3500 93.8 5200 139
125 8.6 4100 110 5200 139
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
24
Table 22. CP200 Series Internal Registration Flow Capacities for 15 psig / 1.0 bar Setpoint
with 1% ABS Pressure Factor Accuracy (PFM Approved)
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
15 psig -0.30 psi 0.30 psi 10 to 20 psig GE30200X012 /
Purple Stripe
1.0 bar -21 mbar 21 mbar 0.69 to 1.4 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
20 1.4 460 12.3 2070 55.5 1600 42.9
25 1.7 1000 26.8 1100 29.5 3376 90.5 3900 105
30 2.1 1200 32.2 2200 59.0 4000 107 4200 113
40 2.8 1600 42.9 2900 77.7 4870 131
50 3.4 2000 53.6 3500 93.8 5100 137
60 4.1 2300 61.6 4000 107 5900 158
80 5.5 2900 77.7 4800 129
100 6.9 3500 93.8 4800 129
125 8.6 4300 115 4800 129
psig bar Body Size: 1 NPT
20 1.4 460 12.3 490 13.1 1000 26.8 2500 67.0
25 1.7 820 22.0 1900 50.9 3600 96.5 4200 113
30 2.1 1200 32.2 2200 59.0 4000 107 4200 113
40 2.8 1600 42.9 2900 77.7 4900 131
50 3.4 1700 45.6 3500 93.8 5100 137
60 4.1 2300 61.6 4000 107 5900 158
80 5.5 2900 77.7 5100 137
100 6.9 3500 93.8 6200 166
125 8.6 4200 113 7500 201
psig bar Body Size: 1-1/4 NPT
20 1.4 460 12.3 2700 72.4 3600 96.5
25 1.7 870 23.3 1600 42.9 4100 110 5500 147
30 2.1 1200 32.2 2200 59.0 4900 131 6000 161
40 2.8 1600 42.9 2900 77.7 6300 169
50 3.4 2000 53.6 3500 93.8 7500 201
60 4.1 2300 61.6 4000 107 8200 220
80 5.5 2900 77.7 5100 137
100 6.9 3600 96.5 6200 166
125 8.6 4300 115 7000 188
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
25
Table 23. CP200 Series Internal Registration Flow Capacities for 20 psig / 1.4 bar Setpoint
with 1% ABS Pressure Factor Accuracy (PFM Approved)
ACCURACY
SETPOINT + / - 1% ABS SET RANGE PART NUMBER /
COLOR
20 psig -0.35 psi 0.35 psi 10 to 20 psig GE30200X012 /
Purple Stripe
1.4 bar -24 mbar 24 mbar 0.69 to 1.4 bar
CAPACITIES IN SCFH / Nm3/h OF 0.6 SPECIFIC GRAVITY NATURAL GAS
Inlet Pressure
Orice Size, Inch / mm
3/16 / 4.8 1/4 / 6.4 3/8 / 9.5 1/2 / 13
SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h SCFH Nm3/h
psig bar Body Size: 3/4 NPT
25 1.7 120 3.2 2086 55.9 3038 81.4
30 2.1 1000 26.8 1900 50.9 3800 102 4100 110
40 2.8 1600 42.9 2700 72.4 4800 129
50 3.4 1900 50.9 3300 88.4 5900 158
60 4.1 2200 59.0 4000 107 6700 180
80 5.5 2900 77.7 5100 137
100 6.9 3600 96.5 6200 166
125 8.6 4300 115 6400 172
psig bar Body Size: 1 NPT
25 1.7 460 12.3 1100 29.5 740 19.8 3000 80.4
30 2.1 1000 26.8 1900 50.9 3800 102 3900 105
40 2.8 1300 34.8 2700 72.4 4800 129
50 3.4 1800 48.2 3300 88.4 5900 158
60 4.1 2200 59.0 4000 107 6700 180
80 5.5 2800 75.0 5200 139
100 6.9 3300 88.4 6300 169
125 8.6 4200 113 7700 206
psig bar Body Size: 1-1/4 NPT
25 1.7 3100 83.1 4300 115
30 2.1 860 23.0 1900 50.9 4100 110 5600 150
40 2.8 1600 42.9 2700 72.4 6400 172
50 3.4 1700 45.6 3300 88.4 7300 196
60 4.1 2300 61.6 3600 96.5 8800 236
80 5.5 2900 77.7 5000 134
100 6.9 3400 91.1 6100 163
125 8.6 4400 118 7200 193
Blank areas indicate where maximum operating inlet pressure for a given orice size is exceeded.
Bulletin 71.1:CP200
26
TOP VIEW
SIDE VIEW
14.15 /
359
2.02 / 51
4.04 / 103
10.37 /
263
6.01 /
153
B
C
MAIN VALVE
GE34260
INCH /
mm
Figure 6. Dimensions
Figure 5. CP200 Series Vent Position and Body Orientation
TYPE 67CP/CPR VENT POSITION
(VENT POSITION 1)
TYPE 67CP/CPR INLET
BODY POSITION 3 OR 4
TYPE 67CP/CPR INLET
TYPE 67CP/CPR VENT POSITION
(VENT POSITION 2)
BODY POSITION 3
TYPE CP200 PIPING POSITIONS
STANDARD POSITION
Bulletin 71.1:CP200
27
GE34260
INCH /
mm
BODY SIZE END CONNECTION STYLE DIMENSIONS, INCH / mm
Inlet Outlet B C
3/4 3/4
NPT
5.84 / 148 9.89 / 2513/4 1
1
3/4
1-1/4 6.02 / 153 10.1 / 2571
1-1/4
NPT BODY
0.89 / 23
4.04 /
103
Figure 6. Dimensions (continued)
Table 24. Dimensions
Type (Select One)
CP200IN (without Token relief)***
CP200IT (with Token relief)
CP205IN (without Token relief and with
Secondary Seat™ Protection)
CP205IT (with Token relief and
Secondary Seat Protection)
CP206IT (with Token relief and Secondary Seat
Protection with bleed to indicate Secondary Seat
is functioning)
Body Size and End Connection Style (Select One)
3/4 NPT***
3/4 x 1 NPT***
3/4 x 1-1/4 NPT***
1 NPT***
1 x 1-1/4 NPT***
1-1/4 NPT***
Outlet Pressure Range (Select One)
1 to 2 psig / 69 mbar to 0.14 bar, Yellow Stripe***
2 to 5 psig / 0.14 bar to 0.34 bar, Orange Stripe***
5 to 10 psig / 0.34 to 0.69 bar, Black Stripe***
10 to 20 psig / 0.69 to 1.4 bar, Purple Stripe***
Orice Size (Select One)
Type CP200
1/8-inch / 3.2 mm***
3/16-inch / 4.8 mm***
1/4-inch / 6.4 mm***
3/8-inch / 9.5 mm***
1/2-inch / 13 mm***
Types CP205 and CP206
1/8-inch / 3.2 mm***
3/16-inch / 4.8 mm***
1/4-inch / 6.4 mm***
5/16-inch / 7.9 mm***
Body Orientation (Select One)
Position 3 (standard)***
Position 4***
Vent Orientation of Types 67CP/67CPR and
CP200 Series (Select One)
Position 1 (standard)***
Position 2***
Certication (Available only on CP200 Series Construction)
Pressure Factor Measurement (PFM)
Ordering Guide
Bulletin 71.1:CP200
©Emerson Process Management Regulator Technologies, Inc., 2008, 2013; All Rights Reserved
Industrial Regulators
Emerson Process Management
Regulator Technologies, Inc.
USA - Headquarters
McKinney, Texas 75070 USA
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574
Asia-Paci c
Shanghai 201206, China
Tel: +86 21 2892 9000
Europe
Bologna 40013, Italy
Tel: +39 051 419 0611
Middle East and Africa
Dubai, United Arab Emirates
Tel: +011 971 4811 8100
Natural Gas Technologies
Emerson Process Management
Regulator Technologies, Inc.
USA - Headquarters
McKinney, Texas 75070 USA
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574
Asia-Paci c
Singapore 128461, Singapore
Tel: +65 6770 8337
Europe
Bologna 40013, Italy
Tel: +39 051 419 0611
Chartres 28008, France
Tel: +33 2 37 33 47 00
Middle East and Africa
Dubai, United Arab Emirates
Tel: +011 971 4811 8100
TESCOM
Emerson Process Management
Tescom Corporation
USA - Headquarters
Elk River, Minnesota 55330-2445, USA
Tels: +1 763 241 3238
+1 800 447 1250
Europe
Selmsdorf 23923, Germany
Tel: +49 38823 31 287
Asia-Paci c
Shanghai 201206, China
Tel: +86 21 2892 9499
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls International LLC,
a business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or speci cations of such
products at any time without notice.
Emerson Process Management Regulator Technologies, Inc. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and
maintenance of any Emerson Process Management Regulator Technologies, Inc. product remains solely with the purchaser.
For further information visit www.emersonprocess.com/regulators
The distinctive swirl pattern cast into every actuator
casing uniquely identi es the regulator as part of the
Fisher® brand Commercial Service Regulator family
and assures you of the highest-quality engineering,
performance, and support traditionally associated
with Fisher®, Francel™ and Tartarini™ regulators.
Visit www.fishercommercialservice.com to access
interactive applications.
Regulators Quick Order Guide
* * * Readily Available for Shipment
* * Allow Additional Time for Shipment
* Special Order, Constructed from Non-Stocked Parts. Consult
Your local Sales Of ce for Availability.
Availability of the product being ordered is determined by the component
with the longest shipping time for the requested construction.
Speci cation Worksheet
Application:
Speci c Use
Line Size
Gas Type and Speci c Gravity
Gas Temperature
Does the Application Require Overpressure Protection?
Yes No If yes, which is preferred:
Relief Valve Monitor Regulator Shutoff Device
Is overpressure protection equipment selection assistance
desired?
Pressure:
Maximum Inlet Pressure (P1max)
Minimum Inlet Pressure (P1min)
Downstream Pressure Setting(s) (P2)
Maximum Flow (Qmax)
Performance Required:
Accuracy Requirements?
Need for Fast Response?
Other Requirements:
