Emerson Cs200 Series Pressure Reducing Regulators Instruction Manual

2015-03-30

: Emerson Emerson-Cs200-Series-Pressure-Reducing-Regulators-Instruction-Manual-681113 emerson-cs200-series-pressure-reducing-regulators-instruction-manual-681113 emerson pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

CS200 Series

Instruction Manual
Form 5832
November 2013

CS200 Series Commercial / Industrial Pressure
Reducing Regulators

P1188

Figure 1. Typical CS200 Pressure Reducing Regulator

Table of Contents
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.

1
3
4
6
7
8
8
8
9
9

Scope of the Manual
This manual provides instructions for the installation,
maintenance, and parts ordering information for
Types CS200IN, CS200IR, CS205IN, CS205IR, and
CS206IR service regulators.

D103119X012

Introduction . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . .
Principle of Operation . . . . . . . . . . . . . . .
Installation and Overpressure Protection
Startup . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustment . . . . . . . . . . . . . . . . . . . . . . .
Shutdown . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . .
Parts Ordering . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . .

Introduction

www.fisherregulators.com

CS200 Series
Table 1. Available Configurations
TYPE NUMBER
C

OPTIONS

0
overpressure protection module
0

Without Overpressure Protection Module

With Secondary Seat™ Protection

With Secondary Seat Protection with bleed to indicate Secondary Seat
is functioning
pressure registration
I

Internal Registration
relief
N

Non-Relief

Internal Relief

Table 2. Inlet Pressure Ratings and Flow and Sizing Coefficients

TYPE

CS200

CS205
and
CS206

ORIFICE SIZE

MAXIMUM
OPERATING INLET
PRESSURE TO
PROVIDE OPTIMUM
PERFORMANCE (1)(2)

Inch

psig

bar

1/8
3/16
1/4
3/8
1/2
1/8
3/16
1/4
5/16

3.2
4.8
6.4
9.5
13
3.2
4.8
6.4
7.9

125
125
125
60
40
125
125
125
100

8.6
8.6
8.6
4.1
2.8
8.6
8.6
8.6
6.9

MAXIMUM
EMERGENCY INLET
PRESSURE(2)
psig

175

FLOW
COEFFICIENTS
(WIDE-OPEN)

bar

12.1

12
24
44
102
172
17
37
65
88

0.4
0.8
1.52
3.3
4.4
0.6
1.4
2.2
2.7

30
30
29
31
39
28
27
30
33

IEC SIZING COEFFICIENTS

0.53
0.58
0.53
0.6
0.97
0.5
0.49
0.5
0.65

0.87
0.82
0.85
0.83
0.72
0.82
0.8
0.8
0.79

0.89

1. Inlet pressures based on lockup performance. For maximum inlet pressure values with optimum regulating performance, refer to the applicable Flow Capacity Table on CS200 Series Bulletin.
2. To comply with ANSI B109.4 relief requirements, the maximum inlet pressure may need to be reduced.

Warning

Failure to follow these instructions or
to properly install and maintain this
equipment could result in an explosion
and/or fire causing property damage and
personal injury or death.
Fisher® regulators must be installed,
operated, and maintained in accordance
with federal, state, and local codes,
rules and regulations, and Emerson
Process Management Regulator
Technologies, Inc. (Regulator
Technologies) instructions.

If the regulator vents gas or a leak
develops in the system, service to
the unit may be required. Failure
to correct trouble could result in a
hazardous condition.
Call a gas service person to service the
unit. Only a qualified person shall install
or service the regulator.

Description
The CS200 Series regulators are typically installed
on industrial and commercial applications. All
constructions include internal pressure registration.
Types CS200IR, CS205IR, and CS206IR contain an
internal relief valve. Types CS200IN and CS205IN do
not contain internal relief.

CS200 Series
Specifications
The Specifications section lists the specifications for the regulators. The following information is stamped on the
regulator at the factory: type number, date of manufacture, spring range, orifice size, maximum inlet pressure, maximum
operating outlet pressure, and outlet pressure which may damage regulator parts.
Available Configurations

Orifice Sizes
See Table 2

Type CS200IN: Basic construction with Internal
pressure registration and Non-Relieving
diaphragm assembly
Type CS200IR: Basic construction with Internal
pressure registration and Relieving
diaphragm assembly
Type CS205IN: Type CS200IN with
Secondary SeatTM Protection
Type CS205IR: Type CS200IR with
Secondary Seat Protection
Type CS206IR: Type CS200IR with
S
econdary Seat Protection with bleed to indicate that
the Secondary Seat is providing lockup
See also Table 1

Flow and IEC Sizing Coefficients
See Table 2
Maximum Inlet Pressures(1)
Emergency: 175 psig / 12.1 bar
Operating: See Table 2
Maximum Outlet Pressures(1)
Casing: 25 psig / 1.7 bar
To Avoid Internal Parts Damage:
5 psi / 0.34 bar differential above outlet
pressure setting
Operating: 2 psig / 138 mbar
Temperature Capabilities(1)(2)
-20 to 150°F / -29 to 66°C

Body Sizes, End Connection Style, and
Pressure Rating(1)
See Table 4

Pressure Registration
Internal

Outlet Pressure Ranges
See Table 3

Approximate Weight
8 pounds / 3.6 kg

Spring Case Vent Connection
1 NPT

1. The pressure/temperature limits in this Instruction Manual and any applicable standard or code limitation should not be exceeded.
2. Product has passed Regulator Technologies testing for lockup, relief start-to-discharge and reseal down to -40°.

Table 3. Outlet Pressure Ranges
SERIES

CS200

spring range
Inches w.c.

mbar

3.5 to 5
4.5 to 6.5
6 to 8
7.5 to 11
10 to 14
12 to 19
18 to 1 psig
1 to 2 psig

9 to 12
11 to 16
15 to 20
19 to 27
25 to 35
30 to 47
45 to 69
69 to 138

part number

color code

GE30198X012
GE30195X012
GE30188X012
GE30189X012
GE30224X012
GE30196X012
GE30225X012
GE30190X012

Red
Purple
Gold
Blue
Unpainted
Green
Orange
Black

spring wire diameter

spring free length

Inch

0.102
0.090
0.111
0.112
0.102
0.112
0.120
0.145

2.59
2.28
2.82
2.84
2.59
2.84
3.04
3.68

3.95
4.32
4.48
4.40
4.78
4.40
4.94
4.66

100
110
114
112
121
112
125
118

Table 4. Body Sizes, Material, End Connection, and Pressure Rating
Series

Body SIZE, NPS

End Connection

Body Material

CS200

3/4
3/4 x 1
3/4 x 1-1/4
1
1 x 1-1/4
1-1/4

NPT

Gray Cast Iron

Pressure Rating
psig

bar

175

12.1

CS200 Series
WIRE SEAL (OPTIONAL)

relief valve stem

control spring

relief valve spring

disk
valve stem

DIAPHRAGM

relief seat
PRESSURE RETAINING PLUG
(DO NOT REMOVE)
pusher post

ERAA03487

lever
orifice

Figure 2. Type CS200IR Pressure Reducing Regulator with Internal Relief Operational Schematic
INLET PRESSURE

OUTLET PRESSURE
Principle
of Operation
ATMOSPHERIC PRESSURE

Type CS200 Base Regulator Operation
Refer to Figure 2. When downstream demand decreases,
the pressure under the diaphragm increases. This pressure
overcomes the regulator setting (which is set by the control
spring). Through the action of the pusher post assembly,
lever, and valve stem, the valve disk moves closer to the
orifice and reduces gas flow. If demand downstream
increases, pressure under the diaphragm decreases.
Spring force pushes the pusher post assembly downward
and the valve disk moves away from the orifice.

CS200 Series with Internal Relief
Refer to Figure 2. The option for Internal Relief is offered
on the Types CS200 and CS205 and is standard on the
Type CS206. Internal relief is used to help minimize
overpressure. Any outlet pressure above the start-todischarge point of the non-adjustable relief spring moves the
diaphragm off of the relief seat, allowing excess pressure
to discharge through the vent. Typical start-to-discharge
values are 7 inches w.c. to 1.5 psi / 17 to 103 mbar above
the outlet pressure setting, depending on control spring and
if the Secondary Seat™ option is present. Refer to Table 5
for Type CS205 lockup values and Type CS206 downstream
build-up values. Refer to the CS200 Series Bulletin for
additional information regarding Internal Relief start-to-

discharge both with and without Secondary Seat Protection.
If emergency conditions should exist that prevent normal
operation of the regulator or internal relief valve, the relief
valve stem acts as a secondary travel stop contacting the
underside of the closing cap and stopping the upward travel
of the relief seat. When the diaphragm continues to rise as
downstream pressure builds, the diaphragm lifts off of the
relief seat to provide relief operation.

Type CS205 with Secondary
Seat Protection
Refer to Figure 3. The Type CS205 provides
Secondary Seat Protection. As downstream demand
decreases and downstream pressure rises to the regulator
pressure lockup value, the regulator will lock up. If,
however, damage has occurred to the primary disk, to the
primary orifice’s seating surface, or debris has become
lodged between the primary disk and primary orifice,
the outlet pressure will continue to rise. This additional
pressure causes the primary disk to apply additional force
to the orifice seating surface, which causes the Secondary
seating surface to move toward the Secondary disk or
sealing surface. If downstream demand decreases to
zero, then the secondary seating surface will contact
the sealing surface to provide lockup. Refer to
Table 5 for approximate lockup values provided by the
Secondary Seat.

CONTROL SPRING

RELIEF V LVE STEM

CS200 Series

VALVE STEM
CONTROL SPRING
RELIEF VALVE STEM

SECONDARY SEAT DETAIL

VALVE STEM
RELIEF VALVE
SPRING

SECONDARY
SEAT DETAIL

RELIEF SEAT

PRESSURE RETAINING
PLUG (DO NOT REMOVE)

ERAA03487

INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE

SECONDARY SEAT™ DETAILED VIEW
PRIMARY DISK

PRIMARY ORIFICE
SEATING SURFACE

elastomeric secondary
seating surface

metallic SECONdARY
ORIFICE SEATING SURFACE

INLET PRESSURE
OUTLET PRESSURE
ATMOSPHERIC PRESSURE

NORMAL OPERATION

secondary seating
surface

NORMAL LOCKUP

DEBRIS OBSTRUCTING
LOCKUP

SECONDARY SEAT
LOCKUP

TYPE CS206
SECONDARY SEAT WITH
METAL TO METAL BLEED

M1131

Figure 3. CS200 Series with Secondary Seat Protection

CP200 Series with Secondary SeatTM Protection

Type CS206 Secondary Seat Protection
with Bleed

Internal relief acting in conjunction with the Type CS206
Secondary Seat Assembly.

The Type CS206 provides small bleed to the downstream
system as an indication that the Secondary Seat is
providing lockup. In the event that the primary orifice
and disk cannot provide lockup, the secondary seating
surface will move into contact with a metal disk. This
metal to metal interface will allow a small amount of gas
to bleed downstream thereby increasing outlet pressure
until the Internal relief valve begins to discharge gas
to the atmosphere. The odor of this discharged gas
provides an indication that the regulator is relying on
the Secondary Seat for overpressure protection. See
Table 5 for the Downstream Pressure Build-up of the

Types CS205 and CS206 Secondary Seat
Protection Limitations

caution
Overpressure conditions can occur
in the downstream piping when the
Secondary Seat Protection is
installed. The Secondary Seat Protection
serves only as a backup to the primary
seat for lockup. Refer to the sections on
Overpressure Protection and Maintenance.

CS200 Series
Table 5. Secondary SeatTM Outlet Pressures
control spring

Spring range

setpoint

type cs205

type cs206

Secondary Seat Shut-off
above Setpoint(1)(2)

Downstream Pressure
Build-up

Color

Part Number

Inch w.c.

mbar

Inch w.c.

mbar

Inch w.c.

mbar

Inch w.c.

mbar

Gold

GE30188X012

6 to 8

15 to 20

25.1

Blue

GE30189X012

7.5 to 11

19 to 27

5.5

29.6

Unpainted

GE30224X012

10 to 14

25 to 35

5.8

1.26 psig

Orange

GE30225X012

18 to 1 psig

45 to 69

1 psig

7.8

1.90 psig

131

Black

GE30190X012

1 to 2 psig

69 to 138

2 psig

138

3.42 psig

236

1. Shutoff with primary orifice / seating surface disabled.
2. Shutoff and build-up per ANSI B109.4 at 125 psig / 8.6 bar inlet pressure.

Secondary Seat Protection does not provide additional
overpressure protection in the event the secondary seat
or disk is damaged by debris or contamination in the
pipeline, or from conditions that would cause the regulator
to go wide-open. When selecting Secondary Seat
Protection, it is recommended that:

outdoor installations, point the spring case
vent downward to allow condensate to
drain (see Figure 4). This minimizes the
possibility of freezing and of water or other
foreign materials entering the vent and
interfering with proper operation.

• Internal Relief is also selected, or the addition of
some other method of overpressure protection be
added in the downstream system as discussed in the
Overpressure Protection section; and

Under enclosed conditions or indoors,
escaping gas may accumulate and be an
explosion hazard. In these cases, the vent
should be piped away from the regulator to
the outdoors.

• A periodic downstream lock-up pressure test is done
to determine if the Secondary Seat Protection option
is serving as the primary seat for shutoff, thereby
indicating that the primary orifice/seat or the disk
are no longer providing shutoff. This determination
is made by checking if the regulator lock-up value is
elevated to or near the values indicated in Table 5,
under the heading Type CS205

Installation and
Overpressure Protection
!

Warning

Personal injury or system damage may
result if this regulator is installed, without
appropriate overpressure protection,
where service conditions could exceed the
limits given on the regulator nameplate.
Regulator installations should
be adequately protected from
physical damage.
All vents should be kept open to permit
free flow of gas to the atmosphere. Protect
openings against entrance of rain, snow,
insects, or any other foreign material
that may plug the vent or vent line. On

caution
The CS200 Series regulators have an
outlet pressure rating lower than their
inlet pressure rating. If actual inlet
pressure can exceed the outlet pressure
rating, outlet overpressure protection is
necessary. However, overpressuring any
portion of the regulators beyond the limits
in the Specifications section may cause
leakage, damage to regulator parts, or
personal injury due to bursting of pressurecontaining parts.
Some type of external overpressure
protection should be provided if inlet
pressure will be high enough to damage
downstream equipment. Common methods
of external overpressure protection include
relief valves, monitoring regulators, shutoff
devices, and series regulation.
If the regulator is exposed to an
overpressure condition, it should be
inspected for any damage that may
have occurred. Regulator operation
below these limits does not preclude
the possibility of damage from external
sources or from debris in the pipeline.

CS200 Series
General Installation Instructions
Before installing the regulator,
• Check for damage, which might have occurred
during shipment.
• Check for and remove any dirt or foreign material,
which may have accumulated in the regulator body.
• Blow out any debris, dirt or copper sulfate in copper
tubing and the pipeline.
• Apply pipe compound to the external threads of the
pipe before installing the regulator.
• Make sure gas flow through the regulator is in the
same direction as the arrow on the body. “Inlet” and
“Outlet” connections are clearly marked.

protect vent pipe
with rain cap

CS200 SERIES
regulator

type 289h
relief valve

Installation Location
• The installed regulator should be adequately
protected from vehicular traffic and damage from
other external sources.
• Install the regulator with the vent pointed vertically
down, see Figure 4. If the vent cannot be installed
in a vertically down position, the regulator must be
installed under a separate protective cover. Installing
the regulator with the vent down allows condensation
to drain, minimizes the entry of water or other debris
from entering the vent, and minimizes vent blockage
from freezing precipitation.
• Do not install the regulator in a location where
there can be excessive water accumulation or ice
formation, such as directly beneath a downspout,
gutter, or roof line of building. Even a protective
hood may not provide adequate protection in
these instances.
• Install the Regulator so that any gas discharge through
the vent or vent assembly is over 3 feet / 0.91 m away
from any building opening.

Regulators Subjected to Heavy
Snow Conditions
Some installations, such as in areas with heavy snowfall,
may require a hood or enclosure to protect the regulator
from snow load and vent freeze over.

Installation with External
Overpressure Protection
If the regulator is used in conjunction with a Type 289H
relief valve, it should be installed as shown in Figure 4.
The outside end of the vent line should be protected with
a rainproof assembly.
The Type 289H is typically set 10-inches w.c. / 25 mbar
higher than the outlet pressure setting of the regulator, up
to 30 inches w.c. / 75 mbar outlet pressure. For pressure
greater than this, set the Type 289H 0.75 psi / 0.05 bar
higher than the outlet pressure setting of the regulator.

regulator vent
pointed downward

Figure 4. CS200 Series Regulator Installed with Vent Pointed
Downward and with a Type 289H Relief Valve
for High Capacity Relief

Vent Line Installation
The CS200 Series regulators have a 1 NPT screened
vent opening in the spring case. If necessary to vent
escaping gas away from the regulator, install a remote
vent line in the spring case tapping. Vent piping should
be as short and direct as possible with a minimum
number of bends and elbows. The remote vent line
should have the largest practical diameter. Vent piping
on regulators with internal relief must be large enough
to vent all relief valve discharge to atmosphere without
excessive backpressure and resulting excessive pressure
in the regulator.
Periodically check all vent openings to be sure that they
are not plugged or obstructed.
Outlet pressure ranges are shown on Table 3. Outlet
pressure greater than 5 psi / 0.34 bar above the setpoint
may damage internal parts such as the diaphragm head
and valve disk. The maximum emergency (casing)
outlet pressure is 25 psig / 1.7 bar.

Startup
caution
Pressure gauges must always be used
to monitor downstream pressure during
startup. Procedures used in putting this
regulator into operation must be planned
accordingly if the downstream system is
pressurized by another regulator or by a
manual bypass.

CS200 Series
If the downstream system is not pressurized by another
regulator or manual bypass valve, use the following
procedure to startup the regulator.
1.
2.
3.
4.
5.

Check to see that all appliances are turned off.
Slowly open the upstream shutoff valve.
Check inlet and outlet pressure for correct values.
Check all connections for leaks.
Turn on utilization equipment and recheck
the pressures.

Adjustment
Note
The range of allowable pressure setting is
stamped on the nameplate. If the required
setting is not within this range, substitute
the correct spring (as shown in Table 3). If
the spring is changed, change the nameplate
to indicate the new pressure range.
A pressure gauge must always be used to monitor
downstream pressure while adjustments are being made.
1. Remove the closing cap (key 60, Figure 5).
2. To increase the outlet setting, turn the adjusting screw
(key 65, Figure 5) clockwise. To decrease the outlet
setting, turn the adjusting screw counterclockwise.
3. Replace the closing cap.

Shutdown
Installation arrangements may vary, but in any
installation it is important that the valves be opened or
closed slowly and that the outlet pressure be vented
before venting inlet pressure to prevent damage caused
by reverse pressurization of the regulator. The steps
below apply to the typical installation as indicated.
1. Open valves downstream of the regulator.
2. Slowly close the upstream shutoff valve.
3. Inlet pressure should be automatically released
downstream as the regulator opens in response to the
lowered pressure on the diaphragm.
4. Close outlet shutoff valve.

Maintenance
!

Warning

To avoid personal injury or equipment
damage, do not attempt any maintenance
or disassembly without first isolating the
regulator from system pressure and relieving
all internal pressure as described
in “Shutdown”.

Regulators that have been disassembled for
repair must be tested for proper operation
before being returned to service. Only parts
manufactured by Regulator Technologies
should be used for repairing Fisher®
regulators. Restart gas utilization equipment
according to normal startup procedures.
Due to normal wear or damage that may
occur from external sources, this regulator
should be inspected and maintained
periodically. The frequency of inspection
and replacement of parts depends upon
the severity of service conditions or the
requirement of local, state, and federal
rules and regulations.

Maintenance on Types CS205 and CS206
Secondary Seat™ Protection
The Type CS205 regulator does not have any means
to alert when the Secondary Seat operates at lockup.
Therefore it is recommended that a periodic lockup
test be done on the regulator to determine if the lockup
pressure has elevated to the values in Table 5. If so, the
regulator primary disk and orifice should be replaced.
Types CS205IR and CS206IR have internal relief. Internal
relief operation on these units is an indication that the
Secondary Seat Protection on the Type CS205IR may not
be working and that the Type CS206 Secondary Seat may
have closed. Maintenance should address any potential
causes for internal relief operation as well as other
regulator malfunctions separate from the Secondary Seat.

Disassembly to Replace Diaphragm
1. Remove the closing cap (key 60, Figure 5). Turn the
adjusting screw (key 65) counterclockwise to ease
spring compression.
2. Remove the adjusting screw and spring (key 38).
3. Remove hex nuts (key 16) and cap screws (key 15).
Separate the upper spring case (key 1) from
the lower casing assembly (key 9). Note
vent orientation.
Note
When disassembling a CS200 Series
regulator, lift the upper spring case
straight up in order to avoid hitting the
relief valve stem (key 44, Figure 5).
4. Slide the diaphragm assembly (key 55) away from
the body (key 70) to unhook the pusher post (key 51)
from the lever (key 10). Lift off the diaphragm head
assembly (key 55).
5. For Types CS200IN and CS205IN (Non-relieving
units), unscrew the retainer screw (key 45, Figure 6)
using a 5/8-inch / 16 mm wrench. The screw retainer

CS200 Series
fastens the lower spring seat (key 43) to the pusher
post (key 51). Unscrewing the screw retainer will
separate the lower spring seat (key 43), diaphragm
and diaphragm assembly (key 55), and pusher post
(key 51).
For Type CS200IR, CS205IR, and CS206IR (units
with internal relief), press down on the upper spring
retainer (key 42, Figure 6) using a 9/16-inch / 14 mm
box-end wrench and remove the retaining ring (key 58).
Slide the upper spring retainer (key 42), the relief
spring (key 41), the lower spring seat (key 43) and the
diaphragm assembly (key 55) off of the relief valve stem
(key 44).
6. Reassemble regulator in the reverse order of the
above steps.

Disassembly to Replace Valve Disk
and Orifice
1. Remove the bolts (key 71, Figure 5) which hold the
lower spring casing (key 9) to the body (key 70).
Separate the lower spring casing from the body.
2. Check the body O-ring (key 21) for wear and replace
as necessary.
3. Examine the valve disk (key 36, Figure 5) for nicks,
cuts, and other damage. Remove the disk by pulling
and replace it with a new part if necessary.
4. a. If the seating edge of the Type CS200 orifice
(key 25, Figure 7) is nicked or rough, remove the
orifice from the body using a 7/8-inch / 22 mm
socket wrench.

b. If equipped with a Type CS205/206
Secondary Seat™ orifice assembly, inspect the
primary seating surface as well as the secondary
seating surface and sealing surface. If nicks or other
damage are present, remove the orifice
assembly from the body using a 7/8-inch / 22 mm
socket wrench.
Apply anti-seize lubricant to the external threads of
the new orifice and reassemble.
Note
If the orifice is being replaced with a
different size, change the nameplate
to state the new size and maximum
inlet pressure.
5. Reassemble the regulator in reverse order of the
above steps.

Regulator Reassembly
It is recommended that a good quality pipe thread sealant
be applied to pressure connections and fittings and a
good quality lubricant be applied to all O-rings except
when replacing key 19, as key 19 is a friction fit O-ring for

holding the stem guide into the lower casing. Also apply
an anti-seize compound to the adjusting screw threads
and other areas as needed. Refer to Figures 5 through 7.

Parts Ordering
The type number, orifice size, spring range, and date of
manufacture are stamped on the nameplate. Always
provide this information in any correspondence with
your local Sales Office regarding replacement parts or
technical assistance.
When ordering replacement parts, reference the key
number of each needed part as found in the following
parts list. Separate kit containing all recommended spare
parts is available.

Parts List
Key Description
Spare Parts (Repair Parts Kit includes keys 21,

36, 55, and 62)
Type CS200
1
Upper Case, Aluminum
2 Vent Screen, 18-8 Stainless steel
3 Retaining Ring, Zinc-plated steel
4 Stabilizer Guide, Stainless steel
5 Stabilizer, 1 inch / 25 mm
6 Spring, Stainless steel
7 Retainer Plate, Zinc-plated steel
8 Stabilizer Screw, Zinc-plated steel (3 required)
9 Lower Casing, Aluminum
10 Lever, Steel
11 Stem, Aluminum
13 Lever Pin, Stainless steel
14 Lever Screw, Steel (2 required)
15 Cap Screw, Steel (8 required)
16 Nut, Steel (8 required)
17 Union Ring, Aluminum
18 Snap Ring, Stainless steel
19* O-ring, Nitrile (NBR)
20 Stem Guide, Aluminum
21* O-ring, Nitrile (NBR)
22* Pipe Plug, Steel, 3/4 NPT
25* Orifice Assembly
Type CS200 without Secondary Seat™
protection, Aluminum
1/8 inch / 3.1 mm
3/16 inch / 4.7 mm
1/4 inch / 6.4 mm
3/8 inch / 9.5 mm
1/2 inch / 13 mm
Type CS205 with Secondary Seat
protection, Brass/Nitrile (NBR)
1/8 inch / 3.1 mm
3/16 inch / 4.7 mm
1/4 inch / 6.4 mm
5/16 inch / 7.9 mm
Type CS206 with Secondary Seat
protection and bleed, Brass/Nitrile (NBR)
1/8 inch / 3.1 mm
3/16 inch / 4.7 mm
1/4 inch / 6.4 mm
5/16 inch / 7.9 mm

Part Number

RCS200X0012
GE24555X012
T1121338982
T1120925072
GE27061X012
GE27063X012
GE35010X012
GE27024X012
GE29724X012
GE24289X012
GE27194X012
GE27439X012
T14397T0012
GE34243X012
GE32059X012
GE32060X012
GE26591X012
T1120637022
1K594906562
GE31962X012
GE45216X012
GE34199X012

1A936709012
00991209012
0B042009012
0B042209012
1A928809012
GE31991X012
GE32008X012
GE32010X012
GE32012X012
GE32007X012
GE32009X012
GE32011X012
GE32014X012

*Recommended spare part.

CS200 Series

S
S

19
19

55
55
19

20
20

72
S
72

38L1
L1

38
55
38

L2
L2

L1
L2
L1

L1
L1
L1

L1
L1

L1 62
62

60
62
60

65
60
65

100
65
100

96
100
96

TORQUE:
TORQUE:
TORQUE:
15
TO 30 INCH POUNDS /
15 TOPOUNDS
30 INCH /POUNDS /
15 TO
1.7
TO 30
3.4INCH
N•m
TO 3.4 N•m
1.7 TO 3.4 1.7
N•m

4
96
4

4 66

5
5

7
7

95
95

8
8

TORQUE:
TORQUE:/ TORQUE:
35 TO 45 FOOT POUNDS
35
TO
45 FOOT /POUNDS /
35 TO 45 FOOT
POUNDS
47 TO
61 N•m
47 TO 61 N•m
47 TO 61 N•m

L1
L1

25
L1
25

L2
L2

27
L2
27

36
36

11
36
11

TORQUE:
TORQUE:
TORQUE:
15
TO 30 INCH POUNDS /
15 TOPOUNDS
30 INCH /POUNDS /
15 TO
1.7
TO 30
3.4INCH
N•m
TO 3.4 N•m
1.7 TO 3.4 1.7
N•m

21
11
21

18
21
18

L2
L2

L2
18
L2

13
L2
13

14
14

10
14
10

10L2
L2

22
L2
22

TORQUE:
TORQUE:
TORQUE:
15
TO 30 INCH POUNDS /
15 TOPOUNDS
30 INCH /POUNDS /
15 TO
1.7
TO 30
3.4INCH
N•m
TO 3.4 N•m
1.7 TO 3.4 1.7
N•m

S
S

42
42

51
2251

main valve

70
70

71
71

TORQUE:
TORQUE:
TORQUE:
10
TO 13 FOOT POUNDS /
10 TOPOUNDS
13 FOOT /POUNDS /
10 TO
TO 18
13 N•m
FOOT
14
14 TO 18 N•m
14 TO 18 N•m

17
17

3
3

2
2

1
1

15
15

TORQUE:
TORQUE:
TORQUE:
63
TO 90 INCH POUNDS /
63 TO 90 INCH POUNDS /
63 TO
7.1
TO 90
10 INCH
N•m POUNDS /
7.1 TO 10 N•m
7.1 TO 10 N•m

top view

side view

ERAA03487

apply LubRICANT (L) / SealANT (s)(1)
L1 = anti-seize lubricant
l2 = silicon grease
s = thread sealant
1. Lubricants and sealants must be selected such that they meet the temperature requirements.

Figure 5. CS200 Series Pressure Reducing Regulator Assemblies

16
16

9
9

CS200 Series

A
55A

55B

55A

NON Relief

standard INTERNAL RELIEF

56
NOTE: DIRECTION OF
RETAINER RING
INSTALLATION
ERAA03487

apply adhesive (A)
A = adhesive

Figure 6. CS200 Series Diaphragm Assemblies

TORQUE:
35 TO 45 - FOOT POUNDS /
47 T0 61 N•m

TORQUE:
12 TO 17 - FOOT POUNDS /
16 T0 23 N•m

Secondary Seat™

Standard Orifice

ERAA03487

apply LubRICANT (L)(1)
L1 = anti-seize lubricant
l2 = silicon grease
1. Lubricants must be selected such that they meet the temperature requirements.

Figure 7. CS200 Series Orifice Assemblies

CS200 Series
Parts List (continued)
Part Number

key

27* O-ring, Nitrile (NBR)
11A8741X052
36* Disk, Nitrile (NBR)
Type C200
GE38132X012
Types CS205 and CS206
GG01395X012
38 Spring, Stainless steel or Music wire
3.5 to 5 inches w.c. / 9 to 12 mbar, Red
GE30198X012
4.5 to 6.5 inches w.c. / 11 to 16 mbar, Purple
GE30195X012
6 to 8 inches w.c. / 15 to 20 mbar, Gold
GE30188X012
7.5 to 11 inches w.c. / 19 to 27 mbar, Blue
GE30189X012
10 to 14 inches w.c. / 25 to 35 mbar, Unpainted GE30224X012
12 to 19 inches w.c. / 30 to 47 mbar, Green
GE30196X012
18 inches w.c. to 1 psig / 45 to 69 mbar, Orange GE30225X012
1 to 2 psig / 69 to 138 mbar, Black
GE30190X012
41 Relief Spring, Stainless steel
GE30194X012
42 Upper Spring Retainer, Aluminum
GE27296X012
43 Spring Seat, Zinc-plated steel
Non-Relief
GE27327X012
Relief
GE28947X012
44 Relief valve stem, Aluminum
GE27297X012
45* Diaphragm Screw retainer, Zinc-plated steel
GE30887X012
51 Pusher Post, Aluminum
Non-Relief
ERAA00875A0
Relief
ERAA00876A0

53
54
55*
56
57
58*
60
62*
65
70

key

Description

Part Number

Post Pin, Stainless steel
Roller Pin, Brass
Diaphragm Assembly, Steel/Nitrile (NBR)
Retaining Ring, Pusher Post Pin, Steel
Slotted Spring Pin, Zinc-plated steel
E-Ring, Copper
Closing Cap, Aluminum
O-ring, Nitrile (NBR)
Adjusting Screw, Aluminum
Body, Gray cast iron
3/4 NPT
3/4 x 1 NPT
3/4 X 1-1/4 NPT
1 NPT
1 x 1-1/4 NPT
1-1/4 NPT
71 Bolt, Zinc-plated steel (2 required)
72 Pipe Plug, Hex Socket, Steel
95 Grommet, Nitrile (NBR)
96 Slip Disk, Stainless steel
100 Lockwire, Stainless steel

GE29761X012
GE27060X012
GE31248X012
GE33772X012
GE33668X012
GE32969X012
GE29244X012
T10275X0012
GE27828X012
GE30991X012
GE30992X012
GE17958X012
GE30993X012
GE18079X012
GE18080X012
GE32061X012
1C333528992
GE35358X012
GG05787X012
T14088T0012

*Recommended spare part.

Industrial Regulators

Natural Gas Technologies

TESCOM

Emerson Process Management
Regulator Technologies, Inc.

Emerson Process Management
Tescom Corporation

USA - Headquarters
McKinney, Texas 75070 USA
Tel: +1 800 558 5853
Outside U.S. +1 972 548 3574

USA - Headquarters
Elk River, Minnesota 55330-2445, USA
Tels: +1 763 241 3238
+1 800 447 1250

Asia-Pacific
Shanghai 201206, China
Tel: +86 21 2892 9000

Asia-Pacific
Singapore 128461, Singapore
Tel: +65 6770 8337

Europe
Selmsdorf 23923, Germany
Tel: +49 38823 31 287

Europe
Bologna 40013, Italy
Tel: +39 051 419 0611

Europe
Bologna 40013, Italy
Tel: +39 051 419 0611
Chartres 28008, France
Tel: +33 2 37 33 47 00

Asia-Pacific
Shanghai 201206, China
Tel: +86 21 2892 9499

Middle East and Africa
Dubai, United Arab Emirates
Tel: +971 4811 8100

For further information visit www.emersonprocess.com/regulators

The distinctive swirl pattern cast into every actuator
casing uniquely identifies the regulator as part of
the Fisher® brand Commercial Service Regulator
family and assures you of the highest-quality
engineering, performance, and support traditionally associated
with Fisher, Tartarini™, and Francel™ regulators. Visit
www.fishercommercialservice.com to access interactive applications.

The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls International LLC,
a business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management Regulator Technologies, Inc., does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and
maintenance of any Emerson Process Management Regulator Technologies, Inc. product remains solely with the purchaser.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c003 61.141987, 2011/02/22-12:03:51
Create Date                     : 2013:11:20 18:00:17+08:00
Metadata Date                   : 2013:11:20 18:00:30+08:00
Modify Date                     : 2013:11:20 18:00:30+08:00
Creator Tool                    : Adobe InDesign CS5.5 (7.5.3)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 9419 bytes, use -b option to extract), (Binary data 11028 bytes, use -b option to extract)
Instance ID                     : uuid:d452ffba-37a1-4628-a957-77b5164a1b4b
Document ID                     : xmp.did:10DE933ECA51E311A2188C1360E7D23C
Original Document ID            : adobe:docid:indd:bd1f4de9-cb02-11df-9702-bbab8b221f57
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:835B903ECA51E311A2188C1360E7D23C
Derived From Document ID        : xmp.did:DBA8107B5818E2118589A8B80CEDEEC4
Derived From Original Document ID: adobe:docid:indd:bd1f4de9-cb02-11df-9702-bbab8b221f57
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:E1DA14991344E011A0AA8F2C286521C8, xmp.iid:E2DA14991344E011A0AA8F2C286521C8, xmp.iid:E3DA14991344E011A0AA8F2C286521C8, xmp.iid:E4DA14991344E011A0AA8F2C286521C8, xmp.iid:9E00E1E1A344E01196DDB7C8EF77BCFD, xmp.iid:D731BEE9B344E011B33ED66EA133D4B5, xmp.iid:19A9B7B4D144E011ADBBFC62D3370B3D, xmp.iid:0E2113366645E011B3EAD41527A9551E, xmp.iid:0F2113366645E011B3EAD41527A9551E, xmp.iid:102113366645E011B3EAD41527A9551E, xmp.iid:112113366645E011B3EAD41527A9551E, xmp.iid:A136D5157E45E011B3EAD41527A9551E, xmp.iid:A236D5157E45E011B3EAD41527A9551E, xmp.iid:41BF7F863946E011B8BCF688CAFDD71C, xmp.iid:B9A5F7AD5246E011B8BCF688CAFDD71C, xmp.iid:BAA5F7AD5246E011B8BCF688CAFDD71C, xmp.iid:CCEC2AB5E64AE011A37EFED9AF0F8994, xmp.iid:CDEC2AB5E64AE011A37EFED9AF0F8994, xmp.iid:CEEC2AB5E64AE011A37EFED9AF0F8994, xmp.iid:CFEC2AB5E64AE011A37EFED9AF0F8994, xmp.iid:D0EC2AB5E64AE011A37EFED9AF0F8994, xmp.iid:D1EC2AB5E64AE011A37EFED9AF0F8994, xmp.iid:BD44A1E8F84AE011A37EFED9AF0F8994, xmp.iid:E2487342B24BE0118753B454EBF8E6F1, xmp.iid:E3487342B24BE0118753B454EBF8E6F1, xmp.iid:E4487342B24BE0118753B454EBF8E6F1, xmp.iid:55672D193751E011B31B94548A1F8EED, xmp.iid:56672D193751E011B31B94548A1F8EED, xmp.iid:2201929E7851E011B31B94548A1F8EED, xmp.iid:2301929E7851E011B31B94548A1F8EED, xmp.iid:E2797155B40BE2118D8F8C8BE11B41BC, xmp.iid:E3797155B40BE2118D8F8C8BE11B41BC, xmp.iid:55B4BBABB50BE2118D8F8C8BE11B41BC, xmp.iid:9FC295D1B50BE2118D8F8C8BE11B41BC, xmp.iid:E4B4FA60B60BE2118D8F8C8BE11B41BC, xmp.iid:E5B4FA60B60BE2118D8F8C8BE11B41BC, xmp.iid:67C3DB79B60BE2118D8F8C8BE11B41BC, xmp.iid:68C3DB79B60BE2118D8F8C8BE11B41BC, xmp.iid:2A953AC6B60BE2118D8F8C8BE11B41BC, xmp.iid:D41DB1E3B60BE2118D8F8C8BE11B41BC, xmp.iid:104293863B0CE211BE40A9025B411895, xmp.iid:B1E6946F3C0CE211BE40A9025B411895, xmp.iid:28E3D8FC3C0CE211BE40A9025B411895, xmp.iid:29E3D8FC3C0CE211BE40A9025B411895, xmp.iid:1D1EA5495F0CE211BE40A9025B411895, xmp.iid:73EAAA495F0CE211BE40A9025B411895, xmp.iid:A57BB6CF5F0CE211BE40A9025B411895, xmp.iid:9763EDB66F0CE211BE40A9025B411895, xmp.iid:9863EDB66F0CE211BE40A9025B411895, xmp.iid:6BA44D5B7D0CE211BE40A9025B411895, xmp.iid:6CA44D5B7D0CE211BE40A9025B411895, xmp.iid:FAD6F5C60B0DE211B756D25A1E0AAD40, xmp.iid:F5ED0FC70B0DE211B756D25A1E0AAD40, xmp.iid:2943EBF65718E2118589A8B80CEDEEC4, xmp.iid:2A43EBF65718E2118589A8B80CEDEEC4, xmp.iid:2B43EBF65718E2118589A8B80CEDEEC4, xmp.iid:2C43EBF65718E2118589A8B80CEDEEC4, xmp.iid:64260D7B5818E2118589A8B80CEDEEC4, xmp.iid:DBA8107B5818E2118589A8B80CEDEEC4, xmp.iid:717266BF6718E2118589A8B80CEDEEC4, xmp.iid:727266BF6718E2118589A8B80CEDEEC4, xmp.iid:87F9D6E26818E2118589A8B80CEDEEC4, xmp.iid:88F9D6E26818E2118589A8B80CEDEEC4, xmp.iid:F568F1A4D11AE311A790CCC7D59A9E3D, xmp.iid:9B47E7375B1CE311A2B4F08710B1BD89, xmp.iid:CBC8426DA41EE311B831AA86C0AFC29F, xmp.iid:922320CCA41EE311B831AA86C0AFC29F, xmp.iid:932320CCA41EE311B831AA86C0AFC29F, xmp.iid:45C42A29BA1EE311B831AA86C0AFC29F, xmp.iid:67365C82BB1EE311B831AA86C0AFC29F, xmp.iid:68365C82BB1EE311B831AA86C0AFC29F, xmp.iid:3AAB8CA6BD1EE311B831AA86C0AFC29F, xmp.iid:3BAB8CA6BD1EE311B831AA86C0AFC29F, xmp.iid:55E170AABE1EE311B831AA86C0AFC29F, xmp.iid:56E170AABE1EE311B831AA86C0AFC29F, xmp.iid:151A128ABF1EE311B831AA86C0AFC29F, xmp.iid:56728853C31EE311B831AA86C0AFC29F, xmp.iid:6801DC5FC41EE311B831AA86C0AFC29F, xmp.iid:6901DC5FC41EE311B831AA86C0AFC29F, xmp.iid:57CC5A93C41EE311B831AA86C0AFC29F, xmp.iid:58CC5A93C41EE311B831AA86C0AFC29F, xmp.iid:26EB6F44D21EE311B831AA86C0AFC29F, xmp.iid:BE5A4906E51EE311B831AA86C0AFC29F, xmp.iid:FAB581F0E71EE311B831AA86C0AFC29F, xmp.iid:FCE54D622421E311A8BF8AC6DC16EBD9, xmp.iid:635658E66E40E311B331EB03F363CA0F, xmp.iid:5AD2EF016F40E311B331EB03F363CA0F, xmp.iid:D8BB2BFC7140E311B331EB03F363CA0F, xmp.iid:FD8BE2D67540E311B331EB03F363CA0F, xmp.iid:611C6EAA2F41E311BFD6BEAA8B16A347, xmp.iid:621C6EAA2F41E311BFD6BEAA8B16A347, xmp.iid:940590C9C951E311AEB3EBD05246E521, xmp.iid:E0DF9417CA51E311AEB3EBD05246E521, xmp.iid:835B903ECA51E311A2188C1360E7D23C, xmp.iid:10DE933ECA51E311A2188C1360E7D23C
History When                    : 2011:03:01 22:52:58+08:00, 2011:03:01 22:52:58+08:00, 2011:03:01 23:12:09+08:00, 2011:03:02 00:00:26+08:00, 2011:03:02 16:05:48+08:00, 2011:03:02 21:25:41+08:00, 2011:03:02 21:49:55+08:00, 2011:03:03 16:12:13+08:00, 2011:03:03 16:30:52+08:00, 2011:03:03 16:36:39+08:00, 2011:03:03 16:37:58+08:00, 2011:03:03 18:07:45+08:00, 2011:03:03 18:26:09+08:00, 2011:03:04 19:03:34+08:00, 2011:03:04 19:38:40+08:00, 2011:03:04 19:38:53+08:00, 2011:03:10 15:40:19+08:00, 2011:03:10 15:44:21+08:00, 2011:03:10 15:54:21+08:00, 2011:03:10 15:55:44+08:00, 2011:03:10 16:08:02+08:00, 2011:03:10 16:09:22+08:00, 2011:03:10 23:10:24+08:00, 2011:03:11 19:22:30+08:00, 2011:03:11 19:27:17+08:00, 2011:03:11 19:37:42+08:00, 2011:03:18 16:09:50+08:00, 2011:03:18 16:10:41+08:00, 2011:03:19 00:08+08:00, 2011:03:19 00:09:13+08:00, 2012:10:01 18:39:53+08:00, 2012:10:01 18:39:53+08:00, 2012:10:01 18:49:27+08:00, 2012:10:01 18:50:30+08:00, 2012:10:01 18:54:31+08:00, 2012:10:01 18:54:31+08:00, 2012:10:01 18:55:13+08:00, 2012:10:01 18:55:13+08:00, 2012:10:01 18:57:21+08:00, 2012:10:01 18:58:10+08:00, 2012:10:02 10:47:37+08:00, 2012:10:02 10:54:08+08:00, 2012:10:02 10:58:05+08:00, 2012:10:02 11:19:20+08:00, 2012:10:02 15:03:37+08:00, 2012:10:02 15:03:37+08:00, 2012:10:02 15:07:22+08:00, 2012:10:02 17:01:12+08:00, 2012:10:02 17:01:12+08:00, 2012:10:02 18:38:51+08:00, 2012:10:02 18:38:51+08:00, 2012:10:03 11:38:20+08:00, 2012:10:03 11:38:21+08:00, 2012:10:17 20:41:25+08:00, 2012:10:17 20:41:25+08:00, 2012:10:17 20:44+08:00, 2012:10:17 20:44+08:00, 2012:10:17 20:45:07+08:00, 2012:10:17 20:45:07+08:00, 2012:10:17 22:34:24+08:00, 2012:10:17 22:34:24+08:00, 2012:10:17 22:42:33+08:00, 2012:10:17 22:42:33+08:00, 2013:09:11 19:02:26+08:00, 2013:09:13 17:59:45+08:00, 2013:09:16 15:48:50+08:00, 2013:09:16 15:51:29+08:00, 2013:09:16 15:51:29+08:00, 2013:09:16 18:24:25+08:00, 2013:09:16 18:34:04+08:00, 2013:09:16 18:48:05+08:00, 2013:09:16 18:49:24+08:00, 2013:09:16 18:50:36+08:00, 2013:09:16 18:56:40+08:00, 2013:09:16 19:00:47+08:00, 2013:09:16 19:02:55+08:00, 2013:09:16 19:30:02+08:00, 2013:09:16 19:37:32+08:00, 2013:09:16 19:38:47+08:00, 2013:09:16 19:38:58+08:00, 2013:09:16 19:38:58+08:00, 2013:09:16 21:16:59+08:00, 2013:09:16 23:31:15+08:00, 2013:09:16 23:52:07+08:00, 2013:09:19 20:09:50+08:00, 2013:10:29 15:51:20+08:00, 2013:10:29 15:52:06+08:00, 2013:10:29 16:13:25+08:00, 2013:10:29 22:07:04+08:00, 2013:10:30 14:51:12+08:00, 2013:10:30 14:51:12+08:00, 2013:11:20 17:54:46+08:00, 2013:11:20 17:56:57+08:00, 2013:11:20 17:58:02+08:00, 2013:11:20 17:58:02+08:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5
History Changed                 : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata
Doc Change Count                : 3943
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 12
Creator                         : Adobe InDesign CS5.5 (7.5.3)

EXIF Metadata provided by EXIF.tools

Emerson Cs200 Series Pressure Reducing Regulators Instruction Manual

Navigation menu

Versions of this User Manual:

Views

Navigation