Emerson Fisher 1061 Data Sheet

: Emerson Emerson-Fisher-1061-Data-Sheet-681931 emerson-fisher-1061-data-sheet-681931 emerson pdf

Open the PDF directly: View PDF .
Page Count: 8

www.Fisher.com

Fisherr1061 Pneumatic Piston Rotary

Actuator

Fisher 1061 pneumatic piston rotary actuators are

used to operate splined-shaft rotary control valves

such as Vee-Balltvalves, eccentric disc valves, and

butterfly valves. The actuator/valve body linkage of

this actuator can be positioned for either

push-down-to-open or push-down-to-close action.

Additionally, the 1061 actuator can be used with a

two-position control signal for on-off service or with a

valve positioner for throttling service. An optional

handwheel actuator is also available to allow for

auxiliary or emergency manual valve operation when

the 1061 piston actuator is not in use. For complete

information on the valve positioner and the manual

handwheel actuator, refer to the appropriate bulletin.

Features

Application Flexibility–Actuator is available in

push-down-to-open or push-down-to-close

construction and may be mounted in any of four

actuator/valve body mounting positions (see figure

2).

Minimal Dead Band–Single-point linkage with

splined and clamped lever minimizes lost motion

and improves control accuracy.

Compact Construction–Compared to similar

actuators, overall size is reduced by as much as 30

percent.

1061 Actuator with FIELDVUE™ DVC6200 Digital Valve

Controller Mounted on a Fisher V500 Valve

W8380-2

Long Service Life–Rugged construction provides

stability, corrosion resistance, and protection from

deformation should the actuator be over-pressured.

Accessibility–Actuator/valve body linkage is

completely enclosed, yet the valve packing

adjustment remains accessible without removing

any parts.

Monitoring Ease–Highly visible travel indicator

allows easy determination of valve position.

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

2

Specifications

Available Configuration

Actuator Sizes: J30, J40, J60, J68, J80,

J100, and J130

Action: Double-acting pneumatic piston rotary

actuator for Jthrottling service when used with

positioner, or Jon-off service when used with

switching devices

Cylinder Operating Pressure

Minimum Recommended: J1.4 bar (20 psig)

without positioner, or J0.35 bar (5 psi) above

actuator requirement with positioner(1).

Maximum Allowable(2)

Sizes 30 and 60: 6.9 bar (100 psig)

Size 40: 10.3 bar (150 psig)

Size 68: 5.9bar(85psig)

Size 80: 10.3 bar (150 psig)

Size 100: 10.3 bar (150 psig)

Size 130: 10.3 bar (150 psig)

Valve Shaft Diameters, mm (Inch)

Size 30: J12.7 (1/2), J15.9 (5/8),J19.1 (3/4),

J22.2 (7/8), J25.4 (1), and J31.8 (1-1/4)

Sizes 40, 60, and 68: J19.1 (3/4), J22.2 (7/8),

J25.4 (1), J31.8 (1-1/4), J38.1 (1-1/2), J44.5

(1-3/4), and J50.8 (2)

Sizes 80 and 100: J44.5 (1-3/4), J50.8 (2), and

J63.5 (2-1/2)

Size 130: J76.2 (3) and J88.9 (3-1/2)

Maximum Valve Shaft Rotation

J90 degrees without travel stop or J60 degrees

with optional travel stop

Maximum Breakout Torque(1)

Size 30: Up to 282 NSm (2500 lbfSin)

Size 40: Up to 847 NSm (7500 lbfSin)

Size 60: Up to 1130 NSm (10,000 lbfSin)

Size 68: Up to 1540 NSm (13,600 lbfSin)

Size 80: Up to 5080 NSm (45,000 lbfSin)

Size 100: Up to 6290 NSm (55,700 lbfSin) with 63.5

mm (2-1/2 in.) valve shaft diameter

Size 130: Up to 19,800 NSm (175,000 lbfSin)

Stroking Time

Dependent on actuator size, rotation, and positioner

if used. If stroking time is critical, consult your

Emerson Process Management sales office.

Construction Materials

Cylinder and Cylinder Flange: Aluminum

Housing Cover: JCast iron or Jaluminum (only for

size 130)

Piston: JAluminum or JNylon-coated piston

(optional only for sizes 30 to 100)

Piston Rod: Chrome-plated stainless steel

Lever: Ductile iron

Sliding Seal: Aluminum

O-Rings: Nitrile

Housing:

Sizes 30, 40, 60, and 68: Cast iron

Sizes 80, 100 and 130: Aluminum

Mounting Yoke: Cast iron

Mounting Yoke Bushing: PTFE and steel

Material Temperature Capabilities with Standard

Elastomers(2)

-34 to 82_C(-30to180_F)

Pressure Connections

1/4 NPT internal, and for optional pipe-away vent,

3/4 NPT internal connection

Size 130 uses 1 NPT internal connection. See table 1

Travel Indication

Graduated scale and pointer located on actuator end

of valve shaft

Mounting Positions

Seefigure2

Approximate Weight

See table 2

1. Actual actuator torque available depends on specific construction and casing pressure. For information on torque requirements of the valve being considered, contact your Emerson Process

Management sales office.

2. The pressure/temperature limits in this manual and any applicable standard or code limitation for actuator should not be exceeded.

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

3

Figure 1. Sectional of Fisher 1061 Actuator

W3827-1 W2288-3

Table 1. Displacement for 90 Degree Rotation

SIZE PISTON DOWN PISTON UP

cm3Inch3cm3Inch3

30

40

60

68

80

100

130

1100

2130

4060

7210

13,000

19,100

41,100

67

130

248

440

794

1165

2508

1200

2230

4380

7110

12,900

18,800

40,200

74

136

267

434

788

1150

2454

Table 2. Approximate Weight

ACTUATOR SIZE kg Lb

30

40

60

68

80

100

130

22

29

39

56

122

135

299

49

63

86

123

246

298

660

Options

Pneumatic Instruments: J3710, J3610JP, or

J3620JP pneumatic or electro-pneumatic positioners

or JFIELDVUE DVC6200 Digital Valve Controllers are

available. Also, the 377 Series trip valves are available

with Jlock-in-last position, Jfail-up, or Jfail-down

action (for specifications, see separate bulletins).

Potentiometer: It is used for remote valve rotation

indication.

Limit Switches: JTopWorx™ DXP M21GNEB limit

switch for one through six single-pole, double-throw

contacts (see separate bulletin), JGOtproximity

switches for one or two single-pole, double-throw

contacts, or JMicro-Switches or NAMCO switches for

one or two single-pole, double-throw or double-pole,

double-throw contacts. GO proximity switch are not

available for size 80, 100 or 130 actuators.

Handwheel Actuator: The Fisher 1078 manual

declutchable actuator (see figure 3) allows auxiliary or

emergency valve operation of sizes 30 through 100

when engaged (see bulletin 61.8:1078).

Cylinder Bypass: The bypass valve is required when a

handwheel actuator is specified.

Locking Mechanism: The locking mechanism shown in

figure 4 is available for sizes J30, J40, J60, and

J68 actuators. The locking mechanism shown in

figure 5 is available for sizes J80 and J100

actuators.

FlowScannertConnections: Optional quick

disconnect connections are available for use with the

portable FlowScanner microprocessor-based

diagnostic testing unit.

Pipe-Away Vent: Some applications use natural gas or

other hazardous gases as a supply pressure to the

actuator. These applications require the actuator

housingtobevented,reducingtheaccumulationof

gases. For new constructions and retrofit kit

information, contact your Emerson Process

Management sales office with complete service

conditions.

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

4

Table 3. Mounting Styles and Positions

MOUNTING ACTION(1)

VALVE SERIES OR DESIGN VALVE SERIES OR DESIGN

BALL/PLUG

ROTATION TO

CLOSE

V250 V150, V200 and

V300

CV500 and

V500

DISC/BALL

ROTATION TO

CLOSE

V250

8510B, 8532,

8560

and 9500

Right-Hand PDTC

PDTO

CCW

CCW

A

B

A

B

A

B

CW

CW

NA

NA

B

A

Left-Hand PDTC

PDTO

CCW

CCW

NA

NA

D

C

D

C

CW

CW

C

D

C

D

Left-Hand

(Optional)(2)

PDTC

PDTO

CW

CW

NA

NA

C

D

NA

NA

NA

NA

NA

NA

NA

NA

1. PDTC–Push-down-to-close, and PDTO–Push-down-to-open.

2. A left hand ball will be required for the 3- through 12-inch Series B and the 14- to 20-inch, with or without attenuator.

Figure 2. Mounting Styles and Positions (also see table 3)

Notes:

Position 1 is standard; positions 2 through 4 (shown in dotted lines) are alternates.

2. By Emerson Process Management definition:

DForward flow is into the face side of the disc , or ball sealing surface.

DReverse flow is into the hub side of the disc or ball.

1

43A6506-A

A1579-5

LEFT-HAND

MOUNTING

STYLE C

STYLE D

STYLE B

STYLE A

RIGHT-HAND

MOUNTING

STYLE A STYLE B

STYLED STYLEC

POSITION 1

POSITION 1

FLOW

POSITION 1

POSITION 1

FLOW

4

3

24

3

33

4

4

2

2

2

STYLES

RIGHT-HAND MOUNTING

LEFT-HAND MOUNTING

1

1

1

1

Installation

The actuator is normally positioned vertically in a

horizontal pipeline. However, four mounting styles

and four positions are possible for each style (see

figure 2).

When looking in the direction of flow in the pipeline,

an actuator is right-hand mounted when it is on the

right side of the pipeline, and an actuator is left-hand

mounted when it is mounted on the left side of the

pipeline.

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

5

Figure 3. Fisher 1078 Declutchable Manual Actuator

41B0314-A

By Emerson Process Management definition, forward

flow is into the face side of the disc or ball, and reverse

flow is into the hub side of the disc or ball.

Dimensions for the 1061 actuator are shown in figure

6. These dimensions should be used in conjunction

with the mounting positions shown in figure 2.

Actuator Locking Mechanism

The 1061 actuator (sizes 30 through 100) is available

with a locking mechanism which may be used to keep

the actuator in the locked position during

maintenance shutdowns (see figures 4 and 5). The

device is intended to preventaccidentaloperationof

the valve during shutdown and does not imply or

qualify a control valve as a safety shutdown device.

Adjustable Travel Stops

An adjustable down travel stop for the 1061 size 30,

40, 60, and 68 actuators is installed in a special

actuator housing. The assembly consists of locking

screws, locknut, special end rod bearing, and special

lever.

As used here, down or downward means in a direction

toward the valve shaft and away from the piston and

diaphragm. Up or upward means in a direction away

from the valve shaft and toward the piston and

diaphragm.

The locking screw can be positioned to limit downward

travel of the actuator lever to any rotation between 0

and 90 degrees. The travel stop is installed similar to

thelockingmechanismshowninfigure4,exceptthe

travel stop does not accommodate a padlock and the

travel stop can be completely unscrewed from the

housing.

An adjustable up travel stop for the 1061 sizes 40

through 100 actuators is installed in the top of a

special actuator cylinder. The top of the special

cylinder is tapped and faced (machined) for the travel

stop. The assembly consists of a screw, locknut, and

pressure seal. The screw can be positioned to limit

upward travel of the piston to any rotation between 30

and 90 degrees. Longer screws are available to further

limit travel.

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

6

Figure 4. Actuator Locking Mechanism for Size 30, 40, 60, and 68 Actuators

MODIFIED

ACTUATOR

HOUSING

PADLOCK

(CUSTOMER

SUPPLIED)

LOCKING

MECHANISM

ACTUATOR

LEVER

34B0458-A

A6808

Figure 5. Actuator Locking Mechanism for Size 80 and 100 Actuators

MOUNTING

PLATE

SAFETY

LOCKOUT

LOCKSCREW

MODIFIED

HOUSING

LEVER

PADLOCK

CAP SCREW (4)

PADLOCK

(CUSTOMER

SUPPLIED)

44B0457-A

A6809

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

7

Table 4. Dimensions

ACTUATOR

SIZE

C E F H PY

w/o Positioner w/3610JP Pos.

mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches

30 171 6.75 378 14.88 53.8 2.12 114 4.50 175 6.88 281 11.07 73.2 2.88

40 206 8.12 425 16.75 63.5 2.50 121 4.75 186 7.31 292 11.50 76.2 3.00

60 267 10.50 406 16.00 63.5 2.50 121 4.75 186 7.31 292 11.50 76.2 3.00

68 324 12.75 483 19.00 63.5 2.50 121 4.75 186 7.31 292 11.50 76.2 3.00

80 324 12.75 714 28.12 123 4.84 213 8.38 345 13.62 452 17.81 127 5.00

100 381 15.00 714 28.12 123 4.84 213 8.38 345 13.62 452 17.81 127 5.00

130 489 19.24 926 36.47 169 6.67 291 11.46 471 18.55 578 22.74 167 6.56

Table 5. Dimensions

VALVE SHAFT DIAMETER

STYLE F MOUNTING: V-LINE, 8532, 8560, AND

ECCENTRICDISCVALVES STYLE G MOUNTING: 9500 SERIES VALVES V

T U W T U W

mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches

12.7 1/2 117 4.62 --- --- 14.3 0.56 117 4.62 --- --- 11.1 0.44 137 5.38

15.9 5/8 117 4.62 --- --- 14.3 0.56 146 5.75 31.7 1.25 11.1 0.44 137(1) 5.38(1)

19.1 and 25.4 3/4 and 1 152 6.00 31.7 1.25 14.3 0.56 146 5.75 31.7 1.25 11.1 0.44 160 6.31

31.8 and 38.1 1-1/4 and

1-1/2 235 9.25 45.9 1.81 17.5 0.69 210 8.25 50.8 2.00 17.5 0.69 148 5.81

44.5 and 50.8 1-3/4 and 2 273 10.75 50.8 2.00 20.5 0.81 241 9.50 69.8 2.75 17.5 0.69 286(2) 11.25(2)

63.5 2-1/2 337 13.25 76.2 3.00 23.8 0.94 --- --- --- --- --- --- 235 9.25

76.2 3(3) 533 21.00 127 5.00 33.5 1.32 --- --- --- --- --- --- 322 12.68

88.9 3-1/2(3) 533 21.00 127 5.00 33.5 1.32 --- --- --- --- --- --- 322 12.68

1. Dimension shown is for eccentric disc,V150, V200, V300, CV500, 8532, and 8560 valves only; For 7600 and 9500 valves, dimension “V” is 160 mm (6.31 inches).

2. Dimension shown is for size 60 and 68 actuators only; for Size 80 and 100 actuators, the dimension “V” is 235 mm (9.25 inches).

3. Dimensions shown are for V260 valves only.

Figure 6. Dimensions (also see tables 4 and 5)

12.7 AND 15.9 mm

(1/2 AND 5/8 INCH) DIA. SHAFT

19.1 mm (3/4 INCH)

AND LARGER DIA. SHAFTS

ACTUATOR/VALVE MOUNTING DIMENSIONS

SIZE 30 ACTUATOR SIZE 40 AND LARGER ACTUATORS

1/4 -18

NPT

1/4 -18

NPT

1/4 -18

NPT

F

P

E

H

YV

C

WW

TT

U

14A7224-D

14A7219-C

B0786-6

1061 Actuator

D100095X012

Product Bulletin

61.2:1061

February 2013

8

Emerson Process Management

Marshalltown, Iowa 50158 USA

Sorocaba, 18087 Brazil

Chatham, Kent ME4 4QZ UK

Dubai, United Arab Emirates

Singapore 128461 Singapore

www.Fisher.com

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they arenot

to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are

governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such

products at any time without notice.

E1987, 2013 Fisher Controls International LLC. All rights reserved.

Fisher, Vee-Ball, FIELDVUE, TopWorx, GO, and FlowScanner are marks owned by one of the companies in the Emerson Process Management business unit of

Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other

marks are the property of their respective owners.

Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance

of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.