EnGenius Technologies ENS500 LONG RANGE WIRELESS 11N OUTDOOR AP/CB User Manual ENS500EXT

Download:
Mirror Download [FCC.gov]
Document ID	1910611
Application ID	jiJ90YPNn3xtZt1ciJXpHQ==
Document Description	User Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	357.39kB (4467374 bits)
Date Submitted	2013-03-04 00:00:00
Date Available	2013-03-04 00:00:00
Creation Date	2013-03-01 16:59:03
Producing Software	Acrobat Distiller 9.4.0 (Windows)
Document Lastmod	2013-03-01 16:59:34
Document Title	ENS500EXT.book
Document Creator	FrameMaker 9.0
Document Author:	Minna

BASIC NETWORK SETTINGS
DYNAMIC IP
Secondary DNS Enter the secondary DNS server address.
Discard Ping on WAN Check to Enable to recognize pings on the ENS500EXT WAN interface or Disable to block pings on the
ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is
valid. Blocking pings provides some extra security from hackers.
Click Accept to save the settings or Cancel to discard changes.
Dynamic IP
Dynamic IP addressing assigns a different IP
address each time a device connects to an ISP
service provider. The service is most commonly
used by ISP cable providers.
Account Name Enter the account name provided
by your ISP.
Domain Name Enter the domain name provided
by your ISP.
MTU The maximum transmission unit (MTU)
specifies the largest packet size permitted for an
internet transmission. The factory default MTU size
for static IP is 1500. The MTU size can be set
between 512 and 1500.
Get Automatically From ISP Click the radio button to obtain the DNS automatically from the DHCP server.
Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually.
Discard Ping on WAN Check to Enable to recognize pings on the ENS500EXT WAN interface or Disable to block pings on the
ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is
valid. Blocking pings provides some extra security from hackers.
Click Accept to save the settings or Cancel to discard changes.
4-13
BASIC NETWORK SETTINGS
POINT-TO-POINT PROTOCOL OVER ETHERNET (PPPOE)
Point-to-Point Protocol over Ethernet (PPPoE)
Point-to-Point Protocol over Ethernet (PPPoE) is
used mainly by ISPs that provide DSL modems to
connect to the Internet.
MTU Enter the maximum transmission unit (MTU).
The MTU specifies the largest packet size
permitted for an internet transmission (PPPoE
default: 1492). The MTU size can be set between
512 and 1492.
Login Enter the username assigned by an ISP.
Password Enter the password assigned by an
ISP.
Service Name Enter the service name of an ISP
(optional).
Connect on Demand Select the radio button to
specify the maximum idle time. Internet connection
will disconnect when it reach the maximum idle
time, but it will automatically connect when user tries to access the network.
Keep Alive Select whether to keep the Internet connection always on, or enter a redial period once the internet lose connection.
Get Automatically From ISP Click the radio button to obtain the DNS automatically from the DHCP server.
Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually.
Discard Ping on WAN Check to Enable to recognize pings on the ENS500EXT WAN interface or Disable to block pings on the
ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is
valid. Blocking pings provides some extra security from hackers.
Click Accept to save the settings or Cancel to discard changes.
4-14
BASIC NETWORK SETTINGS
POINT-TO-POINT TUNNELLING PROTOCOL (PPTP)
Point-to-Point Tunnelling Protocol (PPTP)
The point-to-point tunnelling protocol (PPTP) is
used in association with virtual private networks
(VPNs). There a two parts to a PPTP connection:
the WAN interface settings and the PPTP settings.
MTU Enter the maximum transmission unit (MTU).
The MTU specifies the largest packet size
permitted for an internet transmission (PPPoE
default: 1492). The MTU size can be set between
512 and 1492.
IP Address Enter the router’s WAN IP address.
Subnet Mask Enter the router’s WAN subnet IP
address.
Default Gateway Enter the router’s WAN gateway
IP address.
PPTP Server Enter the IP address of the PPTP
server.
Username Enter the username provided by your
ISP.
Password Enter the password provided by your ISP.
Connect on Demand If you want the ENS500EXT to end the Internet connection after it has been inactive for a period of time,
select this option and enter the number of minutes you want that period of inactivity to last.
Keep Alive If you want the ENS500EXT to periodically check your Internet connection, select this option. Then specify how often
you want the ENS500EXT to check the Internet connection. If the connection is down, the ENS500EXT automatically re-establishes
your connection
Get Automatically From ISP Obtains the DNS automatically from DHCP server.
4-15
BASIC NETWORK SETTINGS
POINT-TO-POINT TUNNELLING PROTOCOL (PPTP)
Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually.
Discard Ping on WAN Check to Enable to recognize pings on the ENS500EXT WAN interface or Disable to block pings on the
ENS500EXT WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is
valid. Blocking pings provides some extra security from hackers.
Click Accept to save the settings or Cancel to discard changes.
4-16
BASIC NETWORK SETTINGS
CONFIGURING LAN SETTINGS
4.3.2 Configuring LAN Settings
IP Address Enter the LAN IP address.
IP Subnet Mask Enter the LAN IP subnet mask.
Use Router As DHCP Server Check this option to enable the
ENS500EXT internal DHCP server.
Starting IP Address Specify the starting IP address range for
the pool of allocated for private IP addresses. The starting IP
address must be on the same subnet as the ending IP address;
that is the first three octets specified here must be the same as
the first three octets in End IP Address.
Ending IP Address Specify the ending IP address range for the
pool of allocated for private IP addresses. The ending IP address
must be on the same subnet as the starting IP address; that is
the first three octets specified here must be the same as the first
three octets in Start IP Address.
WINS Server IP Enter the IP address of the WINS server.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
4-17
BASIC NETWORK SETTINGS
CONFIGURING VPN PASS-THROUGH
4.3.3 Configuring VPN Pass-Through
VPN Pass-through allows a secure virtual private network (VPN) connection between two computers. Enabling the options on this
page opens a VPN port and enables connections to pass through the ENS500EXT without interruption.
PPTP Pass-through Check this option to enable PPTP pass-through mode.
L2TP Pass-through Check this option to enable L2TP pass-through mode.
IPSec Pass-through Check this option to enable IPSec pass-through mode.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
4-18
BASIC NETWORK SETTINGS
CONFIGURING PORT FORWARDING
4.3.4 Configuring Port Forwarding
Port forwarding enables multiple server applications on a LAN to serve clients on a WAN over a single WAN IP address. The router
accepts incoming client packets, filters them based on the destination WAN, or public, port and protocol and forwards the packets to
the appropriate LAN, or local, port. Unlike the DMZ feature, port forwarding protects LAN devices behind the firewall.
NO. Displays the sequence number of the forwarded port.
Name Displays the name of the forwarded port.
Protocol Displays the protocol to use for mapping from the following: TCP, UDP or Both.
Start Port Displays the LAN port number that WAN client packets will be forward to.
End Port Displays the port number that the WAN client packets are received.
Server IP Displays the IP address of the server for the forwarded port.
Enable Click to enable or disable the forwarded port profile.
Modify Click to modify the forwarded port profile.
Delete Click to delete the forwarded port profile.
Click Add Entry to add port forwarding rules.
Click Accept to confirm the changes.
4-19
BASIC NETWORK SETTINGS
CONFIGURING PORT FORWARDING
Service Name Enter a name for the port forwarding rule.
Protocol Select a protocol for the application: Choices are Both, TCP, and UDP.
Starting Port Enter a starting port number.
Ending Port Enter an ending port number. All ports numbers between the starting and
ending ports will forward users to the IP address specified in the IP Address field.
IP Address Enter the IP address of the server computer on the LAN network where
users will be redirected.
Click Save to apply the changes or Cancel to return previous settings.
4-20
BASIC NETWORK SETTINGS
CONFIGURING DEMILITARIZED ZONE
4.3.5 Configuring Demilitarized Zone
Configuring a device on the LAN as a demilitarized zone (DMZ) host allows unrestricted two-way Internet access for Internet applications, such as online video games, to run from behind the NAT firewall. The DMZ function allows the router to redirect all packets
going to the WAN port IP address to a particular IP address on the LAN. The difference between the virtual server and the DMZ function is that a virtual server redirects a particular service or Internet application, such as FTP, to a particular LAN client or server,
whereas a DMZ redirects all packets, regardless of the service, going to the WAN IP address to a particular LAN client or server.
WARNING!
The PC defined as a DMZ host is not protected by the firewall and is vulnerable to malicious network attacks. Do not store or manage
sensitive information on the DMZ host.
DMZ Hosting Select Enable DMZ to activate DMZ functionality.
DMZ Address Enter an IP address of a device on the LAN.
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
4-21
BASIC NETWORK SETTINGS
CONFIGURING WIRELESS LAN
4.4 Configuring Wireless LAN
4.4.1 Configuring Wireless Settings
Instructions on how to configure the wireless and security settings for each of the possible operating modes.
WARNING!
Incorrectly changing these settings may cause the device to stop functioning. Do not modify the settings in this section without a thorough understanding of the parameters.
Access Point Mode
The ENS500EXT supports Access Point Mode. In this mode, users with a wireless client device within range can connect to the
ENS500EXT to access the WLAN.
Wireless Mode Wireless mode supports 802.11a/n
mixed modes.
Channel HT Mode The default channel bandwidth is 40
MHz. The larger the channel, the better the transmission
quality and speed.
Extension Channel Select upper or lower channel. Your
selection may affect the Auto channel function.
Channel / Frequency Select the channel and frequency
appropriate for your country’s regulation.
Auto Check this option to enable auto-channel selection.
AP Detection AP Detection can select the best channel
to use by scanning nearby areas for Access Points.
4-22
BASIC NETWORK SETTINGS
ACCESS POINT MODE
Current Profile Configure up to four different SSIDs. If many client devices will be accessing the network, you can arrange the
devices into SSID groups. Click Edit to configure the profile and check whether you want to enable extra SSIDs.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
SSID Specify the SSID for the current profile.
VLAN ID Specify the VLAN tag for the current profile.
Suppressed SSID Check this option to hide the SSID from
clients. If checked, the SSID will not appear in the site survey.
Station Separation Click the appropriate radio button to allow
or prevent communication between client devices.
Wireless Security For details on wireless security settings, see
Configuring Wireless Security.
Click Save to accept the changes or Cancel to cancel and
return previous settings.
4-23
BASIC NETWORK SETTINGS
CLIENT BRIDGE MODE
Client Bridge Mode
Client Bridge Mode lets you connect two LAN segments via a wireless link as though they are on the same physical network. Since
the computers are on the same subnet, broadcasts reach all machines. As a result, DHCP information generated by the server reach
all client computers as though the clients residing on one physical network.
Wireless Mode Wireless mode supports 802.11a/n
mixed modes.
SSID Specify the SSID if known. This field is completed
automatically if you select an Access Point in the Site
Survey.
Site Survey Scans nearby locations for Access Points.
You can select a discovered Access Point to establish a
connection.
Prefer BSSID Enter the MAC address if known. If you
select an Access Point in the Site Survey, this field is
completed automatically.
Wireless Security For details on wireless security
settings, see Configuring Wireless Security.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
Profiles If you used the Site Survey, the Web
Configurator shows nearby Access Points. To
connect to an Access Point, click the Access
Point’s BSSID.
Click Refresh to scan again.
4-24
BASIC NETWORK SETTINGS
WDS BRIDGE MODE
WDS Bridge Mode
Unlike traditional bridging. WDS Bridge Mode allows you to create large wireless networks by linking several wireless access points
with WDS links. WDS is normally used in large, open areas, where pulling wires is cost prohibitive, restricted or physically impossible.
Wireless Mode Wireless mode supports 802.11a/n mixed
modes.
Channel HT Mode The default channel bandwidth is 40 MHz.
The larger the channel, the better the transmission quality and
speed.
Extension Channel Select upper or lower channel. Your
selection may affect the Auto channel function.
Channel / Frequency Select the channel and frequency
appropriate for your country’s regulation.
Click Accept to confirm the changes or Cancel to cancel and
return previous settings.
4-25
BASIC NETWORK SETTINGS
WDS BRIDGE MODE
Security Select the type of WDS security: None,
WEP, or AES.
WEP Key Enter the WEP key.
AES Pass phrase Enter the AES pass phrase.
MAC Address Enter the MAC address of the
Access Point to which you want to extend wireless
connectivity.
Mode Select Disable or Enable to disable or
enable WDS.
Click Accept to confirm the changes or Cancel to
cancel and return previous settings.
4-26
BASIC NETWORK SETTINGS
CLIENT ROUTER MODE
Client Router Mode
In Client Router Mode, you can access the Internet wirelessly with the support of a WISP. It also supports VPN pass-through for sensitive data secure transmission.
Wireless Mode Wireless mode supports 802.11a/n
mixed modes.
SSID Specify the SSID if known. This field is completed
automatically if you select an Access Point in the Site
Survey.
Site Survey Scans nearby locations for Access Points.
You can select a discovered Access Point to establish a
connection.
Prefer BSSID Enter the MAC address if known. If you
select an Access Point in the Site Survey, this field is
completed automatically.
Wireless Security For details on wireless security
settings, see Configuring Wireless Security.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
Profiles If you used the Site Survey, the Web
Configurator shows nearby Access Points. To
connect to an Access Point, click the Access
Point’s BSSID.
Click Refresh to scan again.
4-27
BASIC NETWORK SETTINGS
CONFIGURING WIRELESS SECURITY
4.4.2 Configuring Wireless Security
The Wireless Security Settings section lets you configure the ENS500EXT’s security modes: WEP, WPA-PSK, WPA2-PSK, WPAPSK Mixed, WPA, WPA2, and WPA Mixed. We strongly recommend you use WPA2-PSK.
Wired Equivalent Privacy (WEP)
Security Mode Select WEP from the drop-down list to begin the
configuration.
Auth Type Select Open System or Shared.
Input Type Select an input type of Hex or ASCII.
Key Length Level of WEP encryption applied to all WEP keys.
Select a 64/128/152-bit password lengths.
Default Key Specify which of the four WEP keys the
ENS500EXT uses as its default.
Key1 - Key4 Specify a password for the security key index. For
security, each typed character is masked by a dot.
Click Save to save the changes or Cancel to cancel and return
previous settings.
4-28
BASIC NETWORK SETTINGS
WI-FI PROTECTED ACCESS PRE-SHARED KEY (WPA-PSK)
Wi-Fi Protected Access Pre-Shared Key (WPA-PSK)
Security Mode Select WPA-PSK from the drop-down list to
begin the configuration.
Encryption Select Both, TKIP, or AES as the encryption type.

Both = uses TKIP and AES.

TKIP = automatic encryption with WPA-PSK; requires passphrase.

AES = automatic encryption with WPA2-PSK; requires
passphrase.
Passphrase Specify the security password. For security, each typed character is masked by a dot.
Group Key Update Interval Specify how often, in seconds, the group key changes.
Click Save to save the changes or Cancel to cancel and return previous settings.
4-29
BASIC NETWORK SETTINGS
WI-FI PROTECTED ACCESS 2 PRE-SHARED KEY (WPA2-PSK)
Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK)
Security Mode Select WPA2-PSK from the drop-down list to
begin the configuration.
Encryption Select Both, TKIP, or AES as the encryption type.

Both = uses TKIP and AES.

TKIP = automatic encryption with WPA-PSK; requires passphrase.

AES = automatic encryption with WPA2-PSK; requires
passphrase.
Passphrase Specify the security password. For security, each typed character is masked by a dot.
Group Key Update Interval Specify how often, in seconds, the group key changes.
Click Save to save the changes or Cancel to cancel and return previous settings.
4-30
BASIC NETWORK SETTINGS
WI-FI PROTECTED ACCESS PRE-SHARED KEY (WPA-PSK) MIXED
Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed
Security Mode Select WPA2-PSK Mixed from the drop-down
list to begin the configuration.
Encryption Select Both, TKIP, or AES as the encryption type.

Both = uses TKIP and AES.

TKIP = automatic encryption with WPA-PSK; requires passphrase.

AES = automatic encryption with WPA2-PSK; requires passphrase.
Passphrase Specify the security password. For security, each typed character is masked by a dot.
Group Key Update Interval Specify how often, in seconds, the group key changes.
Click Save to save the changes or Cancel to cancel and return previous settings.
4-31
BASIC NETWORK SETTINGS
WI-FI PROTECTED ACCESS (WPA)
Wi-Fi Protected Access (WPA)
Security Mode Select WPA from the drop-down list to begin the
configuration.
Encryption Select Both, TKIP, or AES as the encryption type.

Both = uses TKIP and AES.

TKIP = automatic encryption with WPA-PSK; requires passphrase.

AES = automatic encryption with WPA2-PSK; requires
passphrase.
Radius Server Specify the IP address of the RADIUS server.
Radius Port Specify the port number that your RADIUS server
uses for authentication. Default port is 1812.
Radius Secret Specify RADIUS secret furnished by the
RADIUS server.
Group Key Update Interval Specify how often, in seconds, the group key changes.
Radius Accounting Select to enable or disable RADIUS accounting.
Radius Accounting Server Specify the IP address of the RADIUS accounting server.
Radius Accounting Port Specify the port number that your RADIUS accounting server uses for authentication. Default port is 1813.
Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server.
Interem Accounting Interval Specify the interem accounting interval (60 - 600 seconds).
Click Save to save the changes or Cancel to cancel and return previous settings.
4-32
BASIC NETWORK SETTINGS
WI-FI PROTECTED ACCESS 2 (WPA2)
Wi-Fi Protected Access 2 (WPA2)
Security Mode Select WPA2 from the drop-down list to begin
the configuration.
Encryption Select Both, TKIP, or AES as the encryption type.

Both = uses TKIP and AES.

TKIP = automatic encryption with WPA-PSK; requires passphrase.

AES = automatic encryption with WPA2-PSK; requires
passphrase.
Radius Server Specify the IP address of the RADIUS server.
Radius Port Specify the port number that your RADIUS server
uses for authentication. Default port is 1812.
Radius Secret Specify RADIUS secret furnished by the
RADIUS server.
Group Key Update Interval Specify how often, in seconds, the group key changes.
Radius Accounting Select to enable or disable RADIUS accounting.
Radius Accounting Server Specify the IP address of the RADIUS accounting server.
Radius Accounting Port Specify the port number that your RADIUS accounting server uses for authentication. Default port is 1813.
Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server.
Interem Accounting Interval Specify the interem accounting interval (60 - 600 seconds).
Click Save to save the changes or Cancel to cancel and return previous settings.
4-33
BASIC NETWORK SETTINGS
WI-FI PROTECTED ACCESS (WPA) MIXED
Wi-Fi Protected Access (WPA) Mixed
Security Mode Select WPA Mixed from the drop-down list to
begin the configuration.
Encryption Select Both, TKIP, or AES as the encryption type.

Both = uses TKIP and AES.

TKIP = automatic encryption with WPA-PSK; requires passphrase.

AES = automatic encryption with WPA2-PSK; requires
passphrase.
Radius Server Specify the IP address of the RADIUS server.
Radius Port Specify the port number that your RADIUS server
uses for authentication. Default port is 1812.
Radius Secret Specify RADIUS secret furnished by the
RADIUS server.
Group Key Update Interval Specify how often, in seconds, the group key changes.
Radius Accounting Select to enable or disable RADIUS accounting.
Radius Accounting Server Specify the IP address of the RADIUS accounting server.
Radius Accounting Port Specify the port number that your RADIUS accounting server uses for authentication. Default port is 1813.
Radius Accounting Secret Specify RADIUS accounting secret furnished by the RADIUS server.
Interem Accounting Interval Specify the interem accounting interval (60 - 600 seconds).
Click Save to save the changes or Cancel to cancel and return previous settings.
4-34
BASIC NETWORK SETTINGS
CONFIGURING WIRELESS MAC FILTER
4.4.3 Configuring Wireless MAC Filter
Note:
This section applies to Access Point and WDS Access point mode.
Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC addresses. You can manually add a MAC address to restrict the permission to access ENS500EXT. The default setting is Disable Wireless MAC Filters.
ACL Mode Determines whether network access is granted or denied to clients whose MAC addresses appear in the MAC Address
table on this page. Choices are Disable, Deny MAC in the list, or Allow MAC in the list.
MAC Address Filter Enter the MAC address of the device.
Click Add to add the MAC address to the MAC Address table.
Click Apply to apply the changes.
4-35
BASIC NETWORK SETTINGS
CONFIGURING WDS LINK SETTINGS
4.4.4 Configuring WDS Link Settings
Using WDS Link Settings, you can create a wireless backbone link between multiple access points that are part of the same wireless
network. This allows a wireless network to be expanded using multiple Access Points without the need for a wired backbone to link
them, as is traditionally required.
Security Select the type of WDS
security: None, WEP, or AES.
WEP Key Enter the WEP key.
AES Passphrase Enter the AES
passphrase.
MAC Address Enter the MAC address
of the Access Point to which you want to
extend wireless connectivity.
Mode Select Disable or Enable to
disable or enable WDS.
Click Accept to confirm the changes or
Cancel to cancel and return previous
settings.
Note:
You must enter the ENS500EXT’s MAC address in an access point to establish a connection to it. For more information on how to
enter a MAC address in the access point, refer to its documentation. Not all access points support this feature.
4-36
BASIC NETWORK SETTINGS
CONFIGURING WIRELESS ADVANCED SETTINGS
SSID1 to SSID4 Specify the percentage of the wireless traffic that is shaped for a specific SSID.
Wi-Fi Multimedia (WMM) Parameters
WMM manages the priority of audio, video and voice data over a Wi-Fi network so that data from other applications are less likely to
interfere with transmission. The parameters CWmin, CWmax and AIFS together control the priority of the four access categories
(AC).
AC Displays the following access categories that WMM
prioritizes:

AC_VO = voice

AC_VI = video

AC_BE = best effort

AC_BK = background
CWmin Displays the minimum size of the contention window.
CWmax Displays the maximum size of the contention window.
AIFSN Displays the arbitration inter frame space value (AIFS).
TXOP Limit Displays the transfer opportunity limit in units of 32 microseconds.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
4-38
BASIC NETWORK SETTINGS
MANAGEMENT SETUP
4.5 Management Setup
The Management section lets you configure administration, management VLAN, SNMP settings, backup/restore settings, firmware
upgrade, time settings, and log settings. This chapter describes these settings.
4.5.1 Configuring Administrator Account
Click the Administration link under the Management menu to change the user name and password used to log on to the ENS500EXT
Web Configurator. The default user name is admin and the default password is admin. Changing these settings protects the
ENS500EXT configuration settings from being accessed by unauthorized users.
New Name Enter a new username for logging in to the Web
Configurator.
New Password Enter a new password for logging in to the Web
Configurator
Confirm Password Re-enter the new password for confirmation.
Click Save/Apply to apply the changes or Cancel to return previous settings.
Remote Management Enable or disable remote management.
Remote Upgrade Specify whether the ENS500EXT firmware
can be upgraded remotely.
Remote Management Port If remote management is enabled,
enter the port number to be used for remote management. For example: If you specify the port number 8080, enter http://:8080 to access the ENS500EXT Web Configurator.
Click Accept to apply the changes or Cancel to return previous settings.
4-39
BASIC NETWORK SETTINGS
CONFIGURING MANAGEMENT VLAN
4.5.2 Configuring Management VLAN
Click the Management VLAN link under the Management menu to assign a VLAN tag to the packets. A VLAN is a group of computers
on a network whose software has been configured so that they behave as if they were on a separate Local Area Network (LAN).
Computers on VLAN do not have to be physically located next to one another on the LAN
Management VLAN ID If your network includes VLANs and if tagged packets need to pass through the Access Point, enter the
VLAN ID. Otherwise, click No VLAN tag.
Click Accept to confirm the changes or Cancel to cancel and return previous settings.
Note:
If you reconfigure the Management VLAN ID, you may lose your connection to the ENS500EXT. Verify that the DHCP server supports
the reconfigured VLAN ID and then reconnect to the ENS500EXT using the new IP address.
4-40
BASIC NETWORK SETTINGS
CONFIGURING SNMP
4.5.3 Configuring SNMP
SNMP is used in network management systems to monitor network-attached devices for conditions that warrant administrative attention.
SNMP Enable or disable the ENS500EXT SNMP
function.
Contact Enter the contact details of the device.
Location Enter the location of the device.
Community Name (Read Only) Enter the
password for accessing the SNMP community for
read-only access.
Community Name (Read/Write) Enter the
password for accessing the SNMP community for
read and write access.
Trap Destination Address Enter the IP address
where SNMP traps are to be sent.
Trap Destination Community Name Enter the
password of the SNMP trap community.
SNMPv3 Enable or Disable the SNMPv3 feature.
User Name Specify the username for SNMPv3.
Auth Protocol Select the authentication protocol type: MD5 or SHA.
Auth Key (8-32 Characters) Specify the authentication key for authentication.
Priv Protocol Select the privacy protocol type: DES.
Priv Key (8-32 Characters) Specify the privacy key for privacy.
4-41
BASIC NETWORK SETTINGS
CONFIGURING SNMP
Engine ID Specify the engine ID for SNMPv3.
Click Save/Apply to apply the changes or Cancel to return previous settings.
4-42
BASIC NETWORK SETTINGS
CONFIGURING BACKUP/RESTORE SETTINGS
4.5.4 Configuring Backup/Restore Settings
Click the Backup/Restore Setting link under the Management menu to save the ENS500EXT’s current settings in a file on your local
disk or load settings onto the device from a local disk. This feature is particularly convenient administrators who have several
ENS500EXT devices that need to be configured with the same settings.
This page also lets you return the ENS500EXT to its factory default settings. If you perform this procedure, any changes made to the
ENS500EXT default settings will be lost.
Save A Copy of Current Settings Click Backup to save the current configured settings.
Restore Saved Settings from A File To restore settings that have been previously backed up, click Browse, select the file, and
click Restore.
Revert to Factory Default Settings Click Factory Default to restore the ENS500EXT to its factory default settings.
4-43
BASIC NETWORK SETTINGS
CONFIGURING FIRMWARE UPGRADE
4.5.5 Configuring Firmware Upgrade
Firmware is system software that operates and allows the administrator to interact with the router.
WARNING!
Upgrading firmware through a wireless connection is not recommended. Firmware upgrading must be performed while connected to
an Ethernet (LAN port) with all other clients disconnected.
The firmware upgrade procedure can take several minutes. Do not power off the ENS500EXT during the firmware upgrade, as it can cause the
device to crash or become unusable.
To update the firmware version, follow these steps:
1. Download the appropriate firmware approved by EnGenius Networks from an
approved web site.
Note:
Save the firmware file to a local hard drive.
2. Click Choose File.
3. Browse the file system and select the firmware file.
4. Click Upload.
5. The ENS500EXT restarts automatically after the upgrade completes.
4-44
BASIC NETWORK SETTINGS
CONFIGURING SYSTEM TIME
4.5.6 Configuring System Time
Change the system time of the ENS500EXT by manually entering the information, synchronizing the device with a PC, or setup automatic updates through a network time (NTP) protocol server.
Manually Set Date and Time Enter the date and time values in
the date and time fields or click the Synchronize with PC
button to get the date and time values from the administrator’s
PC.
Automatically Get Date and Time Select a time zone from the
drop-down list and check whether you want to enter the IP
address of an NTP server or use the default NTP server.
Enable Daylight Saving Click to enable or disable daylight
savings time. Select the start and stop times from the Start
Time and Stop Time dropdown lists.
Click Save/Apply to apply the changes or Cancel to return
previous settings.
4-45
BASIC NETWORK SETTINGS
CONFIGURING WI-FI SCHEDULE
4.5.7 Configuring Wi-Fi Schedule
Use the Wi-Fi schedule function to control the wireless power ON/OFF service that operates on a routine basis.
Add a Schedule Service
Create a schedule service type and date/time parameters for a specific service.
Schedule Name Enter the description of the schedule
service.
Service Select the type of schedule service, either
Wireless Power ON or Wireless Power OFF.
Day Select the days of the week to enable the schedule
service.
Time of Day Set the start time that the service is active.
Click Add to append the schedule service to the schedule service table, or Cancel to discard changes.
4-46
BASIC NETWORK SETTINGS
SCHEDULE SERVICES TABLE
Schedule Services Table
The Schedule function relies on the GMT time setting acquired from a network time protocol (NTP) server. For details on how to connect the ENS500EXT to an NTP server, see Configuring System Time.
Schedule Table Displays a list of scheduled services for the ENS500EXT. The properties of each service displayed are:
# Displays the ID number of the service in the table.
Name Displays the description of the service.
Service Displays the type of service, either Wireless Power ON or Wireless Power OFF.
Schedule Displays the schedule information of when the service is active.
Select Select one or more services to edit or delete.
Click Delete Selected to delete the selected services or Delete All to delete all services.
Click Apply to save the settings or Cancel to discard changes.
4-47
BASIC NETWORK SETTINGS
CONFIGURING COMMAND LINE INTERFACE
4.5.8 Configuring Command Line Interface
Most users will configure the ENS500EXT through the graphical user interface (GUI). However, for those who prefer an alternative
method there is the command line interface (CLI). The CLI can be access through a command console, modem or Telnet connection.
CLI Select to enable or disable the ability to modify the ENS500EXT via a command line
interface (CLI).
Click Save/Apply to apply the changes or Cancel to return previous settings.
4-48
BASIC NETWORK SETTINGS
CONFIGURING LOGGING
4.5.9 Configuring Logging
Display a list of events that are triggered on the ENS500EXT Ethernet and wireless interfaces. You can consult this log if an unknown
error occurs on the system or when a report needs to be sent to the technical support department for debugging purposes.
Syslog Enable or disable the ENS500EXT syslog function.
Log Server IP Address Enter the IP address of the log server.
Local Log Enable or disable the local log service.
Click Save/Apply to apply the changes or Cancel to return
previous settings.
4-49
BASIC NETWORK SETTINGS
CONFIGURING DIAGNOSTICS
4.5.10 Configuring Diagnostics
The diagnosis feature allow the administrator to verify that another device is available on the network and is accepting request packets. If the ping result returns alive, it means a device is on line. This feature does not work if the target device is behind a firewall or
has security software installed.
Target IP / Domain Name Enter the IP address you would like
to search.
Ping Packet Size Enter the packet size of each ping.
Number of Pings Enter the number of times you want to ping.
Start Ping Click Start Ping to begin pinging.
Trace route target Enter an IP address or domain name you
want to trace.
Start Traceroute Click Start Traceroute to begin the
traceroute operation.
Target Address Enter the IP address of the target PC.
Time period Enter time period for the speed test.
Check Interval Enter the interval for the speed test.
Start Speed Test Click Start Speed Test to begin the speed
test operation.
IPv4 Port Displays the IPv4 port number of the ENS500EXT.
IPv6 Port Displays the IPv6 port number of the ENS500EXT.
4-50
BASIC NETWORK SETTINGS
VIEWING DEVICE DISCOVERY
4.5.11 Viewing Device Discovery
Device Name Displays the name of the devices connected to the network.
Operation Mode Displays the operation mode of the devices connected to the network.
IP Address Displays the IP address of the devices connected to the network.
System MAC Address Displays the system MAC address of the devices connected to the network.
Firmware Version Displays the firmware version of the devices connected to the network.
4-51
BASIC NETWORK SETTINGS
CONFIGURE DENIAL OF SERVICE PROTECTION
4.5.12 Configure Denial of Service Protection
Use TCP SYN Cookies Protection Click to enable TCP SYN
cookies protection.
SYN Flood Attack Protection Click to enable or disable SYN
Flood Attack Protection.
Match Interval Per Second Enter the allowed number of
packets per second.
Limit Packets Enter the maximum number of packets
allowed per request.
UDP Flood Attack Protection Click to enable or disable UDP Flood Attack Protection.
Match Interval Per Second Enter the allowed number of packets per second.
Limit Packets Enter the maximum number of packets allowed per request.
Ping Attack Protection Click to enable or disable ping attack protection.
Click Save/Apply to apply the changes or Cancel to return previous settings.
4-52
BASIC NETWORK SETTINGS
LOGGING OUT
4.5.13 Logging Out
Click Logout to logout from the ENS500EXT.
4-53
APPENDIX A
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
Appendix A
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
WARNING!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
A-1
APPENDIX B
INDUSTRY CANADA STATEMENT
Appendix B
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Important:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
B-1
APPENDIX C
WORLDWIDE TECHNICAL SUPPORT
Appendix C
WorldWide Technical Support
REGION/COUNTRY OF PURCHASE
SERVICE CENTRE
SERVICE INFORMATION
CANADA
Canada
LOS ANGELES, USA
USA
C-1
web site
www.engeniuscanada.com
email
rma@engeniuscanada.com
contact numbers
Toll Free: (+1) 888-397-2788
Local: (+1) 905-940-8181
hours of operation
Monday - Friday
9:00AM to 5:30PM EST (GMT-5)
web site
www.engeniustech.com
email
support@engeniustech.com
contact numbers
Toll Free: (+1) 888-735-7888
Local: (+1) 714-432-8668
hours of operation
Monday - Friday
8:00 AM to 4:30 PM PST (GMT-8)
APPENDIX C
WORLDWIDE TECHNICAL SUPPORT
REGION/COUNTRY OF PURCHASE
SERVICE CENTRE
SERVICE INFORMATION
MIAMI, USA
web site
[ES] es.engeniustech.com
[PT] pg.engeniustech.com
email
miamisupport@engeniustech.com
contact numbers
Miami: (+1) 305-887-7378
Sao Paulo, Brazil: (+55)11-3957-0303
D.F., Mexico:(+52)55-1163-8894
hours of operation
Monday - Friday
8:00 AM to 5:30PM EST (GMT-5)
web site
www.engeniusnetworks.eu
email
support@engeniusnetworks.eu
contact numbers
(+31) 40-8200-887
hours of operation
Monday - Friday
9:00 AM - 5:00 PM (GMT+1)
web site
www.engenius-me.com
email
support@engenius-me.com
contact numbers
Toll Free:
U.A.E.: 800-EnGenius
800-364-364-87
General:
(+971) 4357-5599
hours of operation
Sunday - Thursday
9:00 AM - 6:00 PM (GMT+4)
Mexico, Central and Southern America
NETHERLANDS
Europe
Africa
Middle East
Russia
CIS / Armenia, Azerbaijan, Belarus,
Georgia, Kazakhstan, Kyrgyzstan,
Moldova, Tajikistan,
Turkmenistan, Ukraine,
Uzbekistan
Turkey
Afghanistan
Pakistan
Bangladesh, Maldives,
Nepal, Bhutan, Sri Lanka
DUBAI, UAE
C-2
APPENDIX C
WORLDWIDE TECHNICAL SUPPORT
REGION/COUNTRY OF PURCHASE
Singapore, Cambodia,
Indonesia, Malaysia,
Thailand, Philippines,
Vietnam
China, Hong Kong, Korea
India
South Africa
Oceania
SERVICE CENTRE
SERVICE INFORMATION
SINGAPORE
TAIWAN, R.O.C.
web site
www.engeniustech.com.sg/e_warranty_form
email
techsupport@engeniustech.com.sg
contact numbers
Toll Free:
Singapore: 1800-364-3648
hours of operation
Monday - Friday
9:00 AM - 6:00 PM (GMT+8)
web site
www.engeniusnetworks.com
email
technology@senao.com
Others
Note:
* Service hours are based on the local time of the service center.
* Please visit the website for the latest information about customer service.
C-3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2013:03:01 16:59:34+08:00
Create Date                     : 2013:03:01 16:59:03+08:00
Metadata Date                   : 2013:03:01 16:59:34+08:00
Creator Tool                    : FrameMaker 9.0
Format                          : application/pdf
Title                           : ENS500EXT.book
Creator                         : Minna
Document ID                     : uuid:9fbfd9cd-d061-449d-9c39-a3a29f103218
Instance ID                     : uuid:01a73402-698e-4ae2-b0a3-58374db5c4e7
Producer                        : Acrobat Distiller 9.4.0 (Windows)
Has XFA                         : No
Page Count                      : 48
Author                          : Minna

EXIF Metadata provided by EXIF.tools