EnGenius Technologies ENS500AC AC867 5GHz Outdoor CPE User Manual Users Maual EnStation5 AC rev

Download:
Mirror Download [FCC.gov]
Document ID	3415299
Application ID	89wCqCdrnROoiaRWQYBwrg==
Document Description	Users Maual (EnStation5-AC)_rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	293.83kB (3672847 bits)
Date Submitted	2017-06-06 00:00:00
Date Available	2017-06-08 00:00:00
Creation Date	2017-06-02 09:15:41
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2017-06-02 11:37:16
Document Title	Users Maual (EnStation5-AC)_rev.pdf
Document Creator	Adobe InDesign CS6 (Windows)

Business Solutions
User Manual
EnStation5-AC/EnStationAC
version 1.1
AC867 5GHz Ultra Long-Range Wireless Outdoor Customer
Premises Equipment
IMPORTANT
To install this Access Point please refer to the
Quick Installation Guide included in the product packaging.
Table of Contents
Chapter 1 Product Overview............................................... 4
Key Features/Introduction........................................................ 5
System Requirements............................................................... 6
Package Contents......................................................................... 7
Technical Specifications..............................................................  8
Physical Interface.......................................................................... 10
Wireless MAC Filtering............................................................... 41
Wireless Advanced..................................................................... 42
WPS Mixed-Enterprise: AP/WDS AP Mode........................... 43
WDS Link Settings....................................................................... 44
Client Bridge Settings.............................................................. 45
Guest Network Settings............................................................ 46
Chapter 2 Before You Begin................................................. 11
Computer Settings....................................................................... 12
Hardware Installation................................................................. 15
Mounting the EnStationAC...................................................... 16
Chapter 8 Management ........................................................ 47
Management VLAN Settings.................................................. 48
Advanced Settings....................................................................... 49
CLI Settings/Email Alert............................................................. 50
Time Zone........................................................................................ 52
Auto Reboot Settings................................................................ 53
Wi-Fi Scheduler............................................................................... 54
Tools.................................................................................................. 55
Account/Firmware........................................................................ 57
Backup/Restore ............................................................................. 58
Log...................................................................................................... 60
Logout/Reset................................................................................. 61
Appendix................................................................................. 62
FCC Interference Statement................................................... 63
CE Interference Statement...................................................... 64
Professional Installation Instrution..................................... 71
Chapter 3 Configuring Your Access Point......................... 19
Default Settings./Web Configuration................................ 20
Chapter 4 Building a Wireless Network........................... 21
Access Point / WDS AP Mode................................................. 22
Client Bridge Mode...................................................................... 23
WDS Bridge Mode........................................................................ 24
WDS Station Mode....................................................................... 26
Chapter 5 Status.................................................................... 27
Main Status..................................................................................... 28
Connection...................................................................................... 30
Chapter 6 Network .............................................................. 32
Basic IP Settings............................................................................ 33
Spanning Tree Protocol Setting............................................. 34
Chapter 7 2.4 GHz/5 GHz Wireless....................................... 35
Wireless Settings.......................................................................... 36
Wireless Network.......................................................................... 37
SSID Profile...................................................................................... 39
Wireless Security.......................................................................... 40
Chapter 1
Product Overview
Introduction
Key Features
• Up to 23/26 dBm transmit power enabling long range
connectivity
• Supports IEEE802.11ac/a/n wireless standards with up to 867
Mbps data rate.
• Internal 19dBi high gain directional antenna
• Can be used with included PoE adapter or via 802.3at PoE  
802.3at - capable switches.  (EnStationAC)
• Can be used with included 24V PoE adapter (EnStation5-AC)
• Can be supply 802.3af power source used with included PoE  
adapter power adapter or via 802.3at PoE - capable switches   
(EnStationAC)
• Secured Guest Network option available
• Advanced 256-QAM technology to achieve optimal performance  
throughout ultra-long distance
Introduction
Its high-powered, long-range characteristics make it a cost
effective alternative to ordinary Access Points that don’t
have the range and reach to connect to a growing number
of wireless CPEs who wish to connect to a business
network. The EnStationAC supports the 5 GHz frequency
band for communicating to other 5GHz frequency bands
The EnStationAC/EnStation5-AC is a high-powered, ultra
long-range 2x2   Wireless 802.11ac/a/n Outdoor Access
Point with speeds up to 867 Mbps on both its high-powered
5 GHz radios. It can be configured as an: Access Point, Client
Bridge or WDS (AP, Station & Bridge). The EnStationAC is
designed to operate in a variety of outdoor environments.
Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between
devices, radio interference in the operating environment, and mix of devices in the network. Features and specifications subject to change without notice. Trademarks and registered
trademarks are the property of their respective owners. For United States of America: Copyright © 201˙ EnGenius Technologies, Inc. All rights reserved.
System Requirements
Access Points concurrently. Several EnStationACs can
be networked in a campus setting using the 5 GHz band
between countries. The EnStationAC is easy to install in
virtually any location with its included PoE (Power over
Ethernet) Adapter for quick outdoor installation. The
EnStationAC enables network administrators to control
its transmit power and features settings for selecting
VHT80 bandwidth to perform ture AC transmission. The
EnStationAC also supports wireless encryption including
Wi-Fi Protected Access (WPA-PSK/ WPA2-PSK) Encryption
and IEEE 802.1X with RADIUS.)
The following are the Minimum System Requirements in
order to configure the device.
• Computer with an Ethernet interface or wireless network capability
• Windows OS (XP, Vista, 7, 8, 10), Mac OS, or Linux-based operating
systems
• Web-Browsing Application (i.e.: Internet Explorer, Firefox, Safari, or
another similar browser application)
Package Contents
Package Contents
The EnStationAC package contains the following items:*
The EnStation5-AC package contains the following items:*
• EnStationAC Customer Premises Equipment
• EnStationAC Customer Premises Equipment
• PoE Adapter (EPA5006GP)
• PoE Adapter (EPA2406GP)
• Pole Mount Strap
• Pole Mount Strap
• Wall Mount Bracket Base
• Wall Mount Bracket Base
• Screw Sets Kit
• Screw Sets Kit
• Rubber
• Rubber
• Sealing Nut
• Sealing Nut
• Dynamic Stick
• Dynamic Stick
• Quick Installation Guide
• Quick Installation Guide
*(all items must be in package to issue a refund):
*(all items must be in package to issue a refund):
Technical Specifications - EnStationAC
WDS Station
Standard:
IEEE802.11ac/a/n on 5 GHz
IEEE802.3at
IEEE802.3af
Optimal Performance
Distance Control (Ack Timeout)
Multicast Supported
Data Rate Selection
Auto Channel Selection
BSSID Support
Antenna
Internal 19dBi high gain directional antenna
Physical Interface
2 x 10/100/1000 Gigabit Ethernet Port with PoE support
LAN(PoE) Port supports IEEE802.3at PoE Input
LAN Port supports IEEE802.3af PoE Output
Easily Management
VLAN Tag / VLAN Pass-through
Guest Network
QoS: Complaint with IEEE 802.11e /WMM
RADIUS Accounting
Wireless STA (Client) connection list
Traffic Shaping (Per SSID)
LED Indicator
Power
LAN 1
LAN 2
WLAN
WLAN LED (Weak, Medium, Strong)
Intuitive Tools
SNMP v1/v2c/v3 support
MIB I/II, Private MIB
Save Configuration as Default
CLI Support
WiFi-Scheduler/Auto Reboot
E-mail Alert
Power Requirements
Include PoE Adapter, 54V/0.6A
IEEE802.3at support
Operation Modes
Access Point
Client Bridge
WDS
Reinforcement Security
WEP Encryption-64/128/152 bit
WPA/WPA2 Enterprise (WPA-EAP using TKIP or AES)
Hide SSID in beacons
WDS Detail
WDS AP
WDS Bridge
MAC address filtering up to 32 MACs per SSID
Https Support
SSH
QoS (Quality of Service)
Complaint with IEEE 802.11e standard
Physical/Environment Conditions
Operating:
Temperature: -20 °C to 60 °C (-4 °F to 140 °F)
Humidity (non-condensing): 90% or less
Storage:
Temperature: -30 °C to 80 °C (-22 °F to 176 °F )
Humidity (non-condensing): 90% or less
Technical Specifications - EnStation5-AC
Multicast Supported
Data Rate Selection
Auto Channel Selection
BSSID Support
Standard:
IEEE802.11ac wave2/a/n on 5 GHz
Antenna
Internal 19dBi high gain directional antenna
Easily Management
VLAN Tag / VLAN Pass-through
Guest Network
QoS: Complaint with IEEE 802.11e /WMM
RADIUS Accounting
Wireless STA (Client) connection list
Traffic Shaping (Per SSID)
Physical Interface
2 x 10/100/1000 Gigabit Ethernet Port with PoE support
LAN(PoE) Port supports 24V PoE Input
LED Indicator
Power
LAN 1
LAN 2
WLAN
WLAN LED (Weak, Medium, Strong)
Intuitive Tools
SNMP v1/v2c/v3 support
MIB I/II, Private MIB
Save Configuration as Default
CLI Support
WiFi-Scheduler/Auto Reboot
E-mail Alert
Power Requirements
Include PoE Adapter, 24V/0.6A
Operation Modes
Access Point
Client Bridge
WDS
Reinforcement Security
WEP Encryption-64/128/152 bit
WPA/WPA2 Enterprise (WPA-EAP using TKIP or AES)
Hide SSID in beacons
MAC address filtering, up to 32 MACs per SSID
Wireless STA (Client) connection list
Https Support
SSH Support
WDS Detail
WDS AP
WDS Bridge
WDS Station
Optimal Performance
Distance Control (Ack Timeout)
10
QoS (Quality of Service)
Complaint with IEEE 802.11e standard
Physical/Environment Conditions
Operating:
Temperature: -20 °C to 60 °C (-4 °F to 140 °F)
Humidity (non-condensing): 90% or less
Storage:
Temperature: -30 °C to 80 °C (-22 °F to 176 °F )
Humidity (non-condensing): 90% or less
11
Physical Interface
Dimensions and Weights
Dimension: 190mm (7.48”)
Height: 38mm (1.9”)
Weight: 527g (1.16 lbs)
2 3
1 WLAN Signal LED: Applied on Client Bridge/WDS
     (1) Red: Weak Signal: Connecting quality is bad.
     (2) Yellow: Connecting quality is Normal.
     (3) Green: Connection quality is Good.
2 LAN(PoE) Signal LED
3 LAN Signal LED of the 2nd Port
4 Power Signal:
5 LAN Port 1: Gigabit Ethernet port for RJ-45 cable.
6 LAN Port 2: Gigabit Ethernet port for RJ-45 cable.
12
Chapter 2
Before You Begin
13
Computer Settings
Windows XP/Windows 7/Windows 8/Windows
10
1b. Move your mouse to the lower right hot corner to
display the Charms Bar and select the Control Panel in
Windows 8 OS.
In order to use the Access Point, you must first configure the
TCP/IPv4 connection of your Windows OS computer system.
1a. Click the Start button and open the Control Panel
Windows 8
1c. In Windows 10, click Start to select All APPs to enter
the folder of Windows system for selecting Control
Panel.
Windows XP
Windows 7
Windows 10
14
4. Select Internet Protocol Version 4 (TCP/IPv4) and then
select Properties.
2a. In Windows XP, click Network Connections.
2b. In Windows 7/Windows 8/Windows 10, click View
Network Status and Tasks in the Network and
Internet section, then select Change adapter settings.
3. Right click on Local Area Connection and select Properties.
5. Select Use the following IP address and enter an IP
address that is different from the Access Point and Subnet
mask, then click OK.
15
Note: Ensure that the IP address and Subnet mask are
on the same subnet as the device.
For example: ENH220EXT IP address: 192.168.1.1
PC IP address: 192.168.1.2 – 192.168.1.255
PC Subnet mask: 255.255.255.0
16
Apple Mac OS X
4. In Configure IPv4, select Manually.
1. Go to System Preferences (Which can be opened in the
Applications folder or selecting it in the Apple Menu).
5. Enter an IP address that is different from the Access
Point and Subnet mask then press OK.
2. Select Network in the Internet & Network section.
Note: Ensure that the IP address and Subnet mask are
on the same subnet as the device.
For example: ENH900EXT IP address: 192.168.1.1
PC IP address: 192.168.1.2 – 192.168.1.255
PC Subnet mask: 255.255.255.0
6. Click Apply when done.
3. Highlight Ethernet.
17
Hardware Installation
1. Remove the rear bottom panel.
2. Connect one end of the Ethernet cable into the main
LAN port (PoE) of the Access Point and the other end to
the AP Ethernet port on the PoE Adapter.
3. Connect the Power cord to the PoE Adapter and plug
the other end in to an electrical outlet.
4. Connect the second Ethernet cable into the LAN port of
the PoE Adapter and the other end to the Ethernet port
on the computer.
5. Place the panel back into device
PoE Adapter
Note: The EnStationAC should ONLY be powered via
Ethernet cable connected to included supports both IEEE
802.3at PoE (Power over Ethernet) or the included PoE
Adapter. You may use either one as the power source.
Do NOT use both at the same time.
Ethernet
PC
Power
Outlet
Note: The EnStationAC can supply the 802.3af power
source when used with included PoE Adapter.
18
Mounting the EnStation
Using the provided hardware, the EnStationAC can be attached to a wall or a pole.
1. EnStation
5. Screw Set Kit
2. PoE Adapter&
Power Cord
3. Bracket
4. Pole Mounting Strap
6. Sealing Nut
7. Dynamic Stick
8. Rubber
19
Wall mounting the EnStation
6. Determine the mounting location. Mark and drill two
pilot holes aligning to the screw holes of the bracket
1. Put the included rubber into the bracket.
7. Put wall anchors into the holes and insert screw into the
wall anchor.
2. Plug the dynamic stick into the bracket.
3. Screw the sealing nut and assembled parts, as well as
tighten it.
8. Screw and secrue the bracket in the place.
4. Put the nock washer on the dynamic stick.
5. Assemble t he mounting parts to the EnStation. .
Dimension:
A: Ø5.5*18 mm
B: Ø8*25 mm
20
Pole mounting the EnStation
1. Put the included rubber into the bracket.
6. Thread the open end of the pole strap through the two
tabs on the bracket.
2. Plug the dynamic stick into the bracket.
7. Lock and tighten pole strap to secure bracket to the pole
3. Screw the sealing nut and assembled parts, as well as
tighten it.
4. Put the nock washer on the dynamic stick.
5. Assemble t he mounting parts to the EnStation. .
21
Chapter 3
Configuring Your
Access Point
22
Configuring Your Access Point
2. The default username and password are admin.
Once you have entered the correct username and
password, click the Login button to open the web-base
configuration page.
This section will show you how to configure the device
using the web-based configuration interface.
Default Settings
Please use your Ethernet port or wireless network adapter
to connect the Access Point.
IP Address 192.168.1.1
Username / Password admin / admin
Web Configuration
1. Open a web browser (Internet Explorer/Firefox/Safari/
Chrome) and enter the IP Address http://192.168.1.1
* The model name will be varied by different models
3. If successful, you will be logged in and see the
EnStationAC User Interface.
Note: If you have changed the default LAN IP Address of
the Access Point, ensure you enter the correct IP Address.
23
Chapter 4
Building a Wireless
Network
24
The EnStationAC has the ability to operate in various modes. This chapter describes the operating modes of the EnStationAC.
Access Point Mode
In Access Point Mode, EnStationAC behaves likes a central connection for stations or clients that support IEEE 802.11a/b/g/n
networks. The stations and clients must be configured to use the same SSID (Service Set Identifier) and security password to
associate with the EnStationAC. The EnStationAC supports up to eight (8) SSIDs per band at the same time for secure access.
WDS AP Mode
25
Client Bridge Mode
The EnStationAC essentially acts as a wireless adapter that connects to an access point to allow a system of wireless
access to the network in the Client Bridge mode. Since the computers are on the same subnet, the EnStationAC can
broadcast to reach all end-devices.
If you use the client bridge mode in the EnStationAC, you can use the AP Detection feature to scan for Access Points
within range. When you find an Access Point, configure the EnStationAC to use the same SSID and Security Password as
the Access Point to associate with it.
26
WDS AP Mode
The EnStationAC also supports WDS AP mode. This operating mode allows wireless connections to the EnStationAC using
WDS technology. In this mode, configure the MAC addresses in both Access Points to enlarge the wireless area by enabling
WDS Link settings. WDS supports up to four (4) AP MAC addresses.
27
WDS Bridge Mode
In WDS Bridge Mode, the EnStationAC can wirelessly connect different LANs by configuring the MAC address and
security settings of each EnStationAC device. Use this mode when two wired LANs located a small distance apart want
to communicate with each other. The best solution is to use the EnStationAC to wirelessly connect two wired LANs, as
shown in the following diagram.
WDS Bridge Mode can establish up to four WDS links, creating a star-like network.
Note: WDS Bridge Mode does not act as an Access Point. Access Points linked by WDS are using the same frequency
channel. More Access Points connected together may lower throughput. This configuration can be susceptible to
generate endless network loops in your network, so it is recommended to enable the Spanning Tree function to
prevent this from happening.
28
WDS Station Mode
Station mode expands the WDS by receiving a wireless signal/service and sharing it through the Ethernet port.
29
Chapter 5
Status
30
Main Status
Save Changes
Note: VLAN ID information is only applicable in Access
Point or WDS AP mode.
This page lets you save and apply the settings shown under
Unsaved changes list, or cancel the unsaved changes and
revert to the previous settings that were in effect.
•
Device Status
Clicking the Device Status link under the Overview menu
shows the status information about the current operating
mode.
•
The Device Information section shows general system
information such as Device Name, MAC Address, Current
Time, Firmware Version, and Management VLAN ID
31
The Memory Information section shows usage of
memory such as Total Available, Free, Cached, Buffered
• The Statistics section shows Mac information such as
SSID, MAC address, RX and TX.
• The LAN Information section shows the Local Area
Network settings such as the LAN IP Address, Subnet
mask, and DNS Address.
• The Wireless LAN Information 5 GHz section shows
wireless information such as Operating Mode, Frequency,
and Channel. Since the EnStationAC supports multipleSSIDs, information about each SSID, the ESSID, and
security settings, are displayed
Note: Profile Settings are only applicable in Access Point
and WDS AP modes.
32
Connection
Realtime
Realtime
5 GHz Connection List
The Realtime section contains the following options:
Click the connection link under the Overview menu displays
the connection list of clients associated to the EnStationAC’s
5 GHz, along with the MAC addresses and signal strength
for each client. Clicking Refresh updates the client list.
		CPU Loading: 3 minutes CPU loading percentage
information, it displays current loading, average loading
and peak loading status. Left bar is loading percentage;
button is time tracing. Interval is every 3 seconds
Note: Only applicable in Access Point and WDS AP
modes.
WDS Link List
Click the connection link under the Overview menu. This
page displays the current status of the WDS link, including
WDS Link ID, MAC Address, Link Status and RSSI.
Note: Only applicable in WDS AP and WDS Bridge modes.
33
		Traffic Loading: 2.4GHz and 5GHz and Ethernet port
inbound and outbound traffic by current, average and
peak time.
including associated SSID, BSSID, connection status, wireless
mode, current channel, security, Tx Data Rate(Mbps), Current
noise level and signal strength.
Realtime Connection (Pkts): Overview on current
active network connections. It displays UDP and TCP
packets information and other connection status. UDP
connections curve is in blue; TCP connection curve is
in green; others curve is in red. Below of chart shows
connections source and destination.
Client Bridge Connection Status
Click the connection link under the Overview menu. This
page displays the connection status between Access Point,
34
Chapter 6
Network
35
Basic IP Settings
IPv4/IPv6 Settings
Primary/Secondary DNS: The primary/secondary DNS
address for this device.
This page allows you to modify the device’s IP settings.
Save: Click Save to confirm the changes.
Spanning Tree Protocol (STP) Settings
This page allows you to modify the Spanning Tree settings.
Enabling the Spanning Tree protocol will prevent network
loops in your LAN network.
IP Network Settings: Select whether the device IP address
will use a static IP address specified in the IP address field
or be obtained automatically when the device connects to
a DHCP server.
Spanning Tree Status: Enables or disables the Spanning
Tree function.
Hello Time: Specifies Bridge Hello Time in seconds. This
value determines how often the device sends handshake
packets to communicate information about the topology
throughout the entire Bridged Local Area Network.
IP Address: The IP address of this device.
Subnet Mask: The IP Subnet mask of this device.
Max Age: Specifies Bridge Max Age in seconds. If another
bridge in the spanning tree does not send a hello packet for
a long period of time, it is assumed to be inactive.
Gateway: The Default Gateway of this device. Leave it
blank if you are unsure of this setting.
36
Forward Delay: Specifies Bridge Forward Delay in seconds.
Forwarding delay time is the time spent in each of the
Listening and Learning states before the Forwarding state
is entered. This delay is provided so that when a new bridge
comes onto a busy network, it analyzes data traffic before
participating in the network.
Priority: Specifies the Priority Number. A smaller number
has a greater priority than a larger number.
Save: Click Save to confirm the changes.
37
Chapter 7
Wireless
38
Wireless
Wireless Settings
Device Name: Enter a name for the device. The name you
type appears in SNMP management. This name is not the
SSID and is not broadcast to other devices.
Save: Click Save to confirm the changes.
39
Select Auto to enable auto-channel selection.
This page displays the current status of the Wireless
settings of the EnStationAC.
Transmit Power: Sets the power output of the wireless
signal.
Wireless Network
Data Rate: Select a data rate from the drop-down list. The
data rate affects throughput of data in the EnStationAC.
Select the best balance for you and your network but note
that the lower the data rate, the lower the throughput,
though transmission distance is also lowered.
RTS/CTS Threshold: Specifies the threshold package size
for RTC/CTS. A small number causes RTS/CTS packets to be
sent more often and consumes more bandwidth.
Operation Mode: Select Operation Mode. The EnStation
supports multi-operation modes: Access Point, Client
Bridge, or WDS(WDS AP, WDS Bridge, and WDS Station).
Client Limits: Limits the total number of clients.
Aggregation: Merges data packets into one packet. This
option reduces the number of packets, but also increases
packet sizes.
Wireless Mode: Supports 802.11ac/a/n mixed mode in 5
GHz.
Channel HT Mode: The default channel bandwidth is 20
MHz/ 40 /80 MHz. The larger the channel, the greater the
transmission quality and speed.
Extension Channel: Select the upper or lower channel.
Your selection may affect the Auto channel function.
Channel: Select the approriate channel and frequency.
40
AP Detection: AP Detection can select the best channel to
use by scanning nearby areas for Access Points.
Distance: Specifies the distance between Access Points
and clients. Note that longer distances may drop higherspeed connections.
Save: Click Save to confirm the changes or Cancel to cancel
and return to previous settings.
41
SSID Profile
includes VLANs, you can specify a VLAN ID for packets pass
through the Access Point with a tag.
Wireless Security: See the Wireless Security section.
VLAN Isolation: Restrict clients communicating with
different VIDs by selecting the radio button.
L2 Isolation: Enable this function prevenet client devices
to communicate on the both WLAN and LAN.
Save: Click Save to accept the changes.
Current Profile: You can configure up to sixteen (16)
different SSIDs (eight (8) per band). If multiple client
devices will be accessing the network, you can arrange the
devices into SSID groups. Click Edit to configure the profile
and check whether you want to enable extra SSID.
SSID: Specifies the SSID for the current profile.
Suppressed SSID: Check this option to hide the SSID from
clients. If checked, the SSID will not appear in the site survey.
Station Separation: Click the appropriate radio button to
allow or prevent communication between client devices.
VID: Specifies the VLAN tag for each profile. If your netowrk
42
Wireless Security
Default Key: Select the Key you wish to be the default.
Transmitted data is ALWAYS encrypted using the Default
Key; the other Keys are for decryption only. You must enter
a Key Value for the Default Key.
The Wireless Security section lets you configure the
EnStationAC’s security modes: WEP, WPA-PSK, WPA2-PSK,
WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. It is strongly
recommend that you use WPA2-PSK.
Encryption Key Number: Enter the Key Value or values you
wish to use. Only the Key selected as Default is required.
The others are optional.
Auth Type: Select Open System or Shared Key.
* Setting of WPA-PSK, WPA2-PSK and WPA-PSK Mixed
(Pre-Shared Key):
Input Type:
ASCII: Regular Text (recommended)
Hexadecimal Numbers (For advanced users)
Encryption: You may select AES, TKIP or Both (TKIP+AES)
to be the encryption type you would like. Please ensure
that your wireless clients use the same settings.
Key Length: Select the desired option and ensure that
wireless clients use the same setting. Your choices are 64,
128, and 152-bit password lengths.
Passphrase: Wireless clients must use the same Key to
43
Radius Server: Enter the IP address of the Radius server.
associate the device. If using ASCII format, the Key must
be from 8 to 63 characters in length. If using HEX format,
the Key must be 64 HEX characters in length.
Radius Port: Enter the port number used for connections
to the Radius server.
Group Key Update Interval: Specifies how often, in
seconds, the Group Key changes. The default value is 3600.
Radius Secret: Enter the secret required to connect to the
Radius server.
Radius Accounting: Enable or disable accounting feature.
Radius Accounting Server: Enter the IP address of the
Radius accounting server.
Radius Accounting Port Enter the port number used for
connections to the Radius accounting server.
Radius Accounting Secret: Enter the secret required to
connect to the Radius accounting server.
Interim Accounting Interval: Specifies how often, in
seconds, the accounting data sends.
Note: 802.11n does not allow WEP/WPA-PSK TKIP/
WPA2-PSK TKIP security mode. The connection mode
will automatically change from 802.11n to 802.11g
* Setting of WPA-Enterprise & WPA2-Enterprise (PreShared Key):
Encryption: Select the WPA encryption type you would like.
Please ensure that your wireless clients use the same settings.
44
Wireless MAC Filtering
Wireless MAC Filtering is used to allow or deny network
access to wireless clients (computers, tablet PCs, NAS,
smartphones, etc.) according to their MAC addresses. You
can manually add a MAC address to restrict permission to
access the EnStationAC. The default setting is: Disable
Wireless MAC Filter.
ACL Mode: Determines whether network access is granted
or denied to clients whose MAC addresses appear in the
Note: Only applicable in Access Point and WDS AP
modes.
Add: Click Add to add the MAC address to the MAC address
table.
MAC address table on this page. Your choices are: Disabled,
Deny MAC in the list, or Allow MAC in the list.
MAC Address: Enter the MAC address of the wireless client.
Delete: Delete the selected entries.
Save: Click Save to apply the changes.
45
Wireless Advanced
Wireless Traffic Shaping
Traffic shaping regulates the flow of packets leaving
an interface to deliver improved Quality of Service. The
function will allow administrators to restrict the wireless
bandwidth per SSID.
Enable Traffic Shaping: Check this option to enable
Wireless Traffic Shaping.
Download Limit: Specifies the wireless transmission
bandwidth used for downloading.
Upload Limit: Specifies the wireless transmission
bandwidth used for uploading.
Save: Click Save to confirm the changes.
46
WDS Link Settings
WDS Link Settings
Using the WDS (Wireless Distribution System) feature will
allow a network administrator or installer to connect to
Access Points wirelessly. Doing so will extend the wired
infrastructure to locations where cabling is not possible or
inefficient to implement.
Note: Compatibility between different brands and
models of Access Points is not guaranteed. It is
recommended that the WDS network be created using
the same models for maximum compatibility.
Security: Select None or AES from the drop-down list.
AES Passphrase: Enter the Key Values you wish to use.
Other Access Points must use the same Key to establish a
WDS link.
Also note: All Access Points in the WDS network need
to use the same Channel and Security settings.
MAC Address: Enter the Access Point’s MAC address to
where you want to extend the wireless area.
To create a WDS network, please enter the MAC addresses
of the Access Points that you want included in the WDS.
There can be a maximum of four Access Points.
Mode: Select to disable or enable from the drop-down list.
Note: Only applicable in WDS AP and WDS Bridge modes.
Save: Click Save to confirm the changes.
47
Client Bridge/WDS Station Settings
Save: Click Save to accept the changes
No.: Display the setting value
SSID: You can click scan under AP detection to search
perform the AP detection to select the proper SSID.
Edit: Click it to implement the advanced settings
Prefer BSSID: You can insert the prefer BSSID or enter
the specific SSID to be associated with the Access Point.
SSID: You can implement the AP detection to select the
proper SSID.
Security Mode: Select the correct security mode and
insert the correct encryption type. Please refer the
wireless security section in page 42.
48
Guest Network Settings
Ending IP Address: The last IP Address in the range of
addresses assigned by the DHCP server.
Adding a guest network allows visitors to use the Internet
without giving out your office or company wireless
security key. You can add a guest network to each wireless
network in the 5 GHz ac/a/n frequencies.
RSSI Threshold
RSSI Threshold: Enable the Fast Handover feature by
ensuring that each client is served by at least one Access
Point at any time. Access Points continuously monitor
the connectivity quality of any client in their range and
efficiently share this information with other Access Points
in the vincinity of that client to coordinate which of them
should serve the client best.
SSID: Specifies the SSID for the current profile.
Suppressed SSID: Check this option to hide the SSID from
clients. If checked, the SSID will not appear in the site survey.
RSSI: Enter the RSSI (Received Signal Strength Index) in
order to determine the handover procedure which the
current wireless link will terminate. RSSI is an indication of
the power level being received by the antenna. Therefore,
the higher the RSSI number, the stronger the signal.
Station Separation: Click the appropriate radio button to
allow or prevent communication between client devices.
IP Address: The IP Address of this device.
Subnet Mask: The IP Subnet mask of this device.
Starting IP Address: The first IP Address in the range of
the addresses by the DHCP server.
49
Chapter 8
Management
50
Management VLAN Settings
Management VLAN: If your network includes VLANs, you
can enable Management VLAN ID for packets passing
through the Access Point with a tag.
This page allows you to assign a VLAN tag to packets sent
over the network. A VLAN is a group of computers on a
network whose software has been configured so that they
behave as if they were on a separate Local Area Network
(LAN). Computers on VLAN do not have to be physically
located next to one another on the LAN.
Save: Click Save to confirm the changes or Cancel to cancel
and return to previous settings.
Note: If you reconfigure the Management VLAN ID, you
Note: Only applicable in Access Point and WDS AP
modes.
may lose your connection to the EnStationAC. Verify
that the DHCP server supports the reconfigured VLAN
ID and then reconnect to the EnStationAC using the
new IP address.
51
Advanced Settings
SNMP Settings
Location: Specifies the location of the device.
This page allows you to assign the Contact Details, Location,
Community Name, and Trap Settings for a Simple Network
Management Protocol (SNMP). SNMP is a networking
management protocol used to monitor network attached
devices. SNMP allows messages (called protocol data units)
to be sent to various parts of the network. Upon receiving
these messages, SNMP compatible devices (called agents)
returns the data stored in their Management Information
Bases.
Community Name (Read Only): Specifies the password
for the SNMP community for read only access.
Community Name (Read/Write): Specifies the password
for the SNMP community with read/write access.
Trap Destination Address: Specifies the IP address of the
computer that will receive the SNMP traps.
Trap Destination Community Name: Specifies the
password for the SNMP trap community.
SNMPv3: Enables or disables the SNMPv3 feature.
User Name: Specifies the username for SNMPv3.
Auth Protocol: Selects the authentication protocol type:
MDS or SHA.
Auth Key: Specifies the authentication key.
Priv Protocol: Selects the privacy protocol type: DES.
Priv Key: Specifies the privacy key for privacy.
Engine ID: Specifies the engine ID for SNMPv3.
SNMP Enable/Disable: Enables or disables the SNMP
feature.
Apply Save: Click Apply Save to apply the changes.
Contact: Specifies the contact details of the device.
52
CLI Settings
Email Alert
You can use the Email Alert feature to send messages
to the configured email address when particular system
events occur.
Note: Do NOT use your personal email address as it can
unnecessarily expose your personal email login credentials.
Use a separate email account made for this feature instead
CLI: The Command Line Interface (CLI) allows you to type
commands instead of choosing them from a menu or
selecting an icon.
SSH: Enable Secure Shell (SSH) to make secure, encrypted
connections in the network. Secure Shell is a network
protocol that allows data to be exchanged using a secure
channel between two network devices.
From: Enter the email address to show the sender of the
email.
HTTPS: Enable HTTPS to transfer and display web content
securely. The Hypertext Transfer Protocol over SSL (Secure
Socket Layer) is a TCP/IP protocol used by web servers to
transfer and display web content securely.
To: Enter the address that you wish to send emails to.
Subject: Enter the text that you wish to appear in the
email’s subject line.
53
Username: Enter the username for the email account that
will be used to send emails.
Password: Enter the password for the email account that
will be used to send emails.
SMTP Server: Enter the IP address or hostname of the
outgoing SMTP server.
Port: Enter the SMTP port number to use for outbound
emails.
54
Time Zone
Time Setting
Start: Select the day, month, and time when daylight
savings time starts.
This page allows you to set the internal clock of the
EnStationAC.
End: Select the day, month, and time when daylight savings times ends.
Manually Set Date and Time: Manually specify the
date and time.
Automatically Get Date and Time: Select and check
whether you wish to enter the IP address of an NTP
server or use the default NTP server to have the
internal clock set automatically.
Enable Daylight Saving: Check whether daylight
savings applies to your area.
55
Auto Reboot Settings
You can specify how often you wish to reboot the
EnStationAC.
Auto Reboot Setting: Enables or disables the Auto
Reboot function.
Frequency of Auto Reboot: Specifies how often you
wish to reboot the EnStationAC by Min, Hour, Day or
Week.
Timer: Select the day and enter the time you would like
to reboot automatically.
Save: Click Save to apply the changes.
56
Wi-Fi Scheduler
drop-down list.
The Wi-Fi Scheduler can be created for use in enforcing
rules. For example, if you wish to restrict web access to
Mon-Fri from 3pm to 8pm, you could create a schedule
selecting Mon, Tue, Wed, Thu and Fri while entering a Start
time of 3pm and End Time of 8pm to limit access to these
times.
Day(s): Place a checkmark in the boxes for the desired days
or select the All Week radio button to select all seven days
of the week.
Duration: The Start Time is entered in two fields. The first
box is for hours and the second box is for minutes. The End
Time is entered in the same format as the Start time.
Status: Enables or disables the Wi-Fi scheduler function.
Wireless Radio: Select 2.4 GHz or 5 GHz from the dropdown list for the preferred band type.
SSID Selection: Select a SSID from the drop-down list.
Schedule Templates: Select a schedule template from the
57
Tools
Ping Test Parameters
Target IP: Enter the IP address you would like to trace
This page allows you to analyze the connection quality of
the EnStationAC and trace the routing table to a target in
the network.
Speed Test Parameters
Target IP: Enter the IP address you would like to search.
Target IP: Enter the IP address you would like to test.
Ping Packet Size: Enter the packet size of each ping.
Start Ping: Click Start Ping to begin pinging the target
device (via IP).
Number of Pings: Enter the number of times you wish to
ping.
Traceroute Target: Enter the IP address or domain name
you wish to trace.
Traceroute Test Parameter
Start Traceroute: Click Start Traceroute to begin the trace
route operation.
58
Device Discovery
This page allows you to discover devices from network
for Operation Mode, IP Address, System MAC Address and
Firmware version.
59
Account
Firmware
This page allows you to change the EnStationAC username
and password. By default, the username is: admin and the
password is: admin. The password can contain from 0 to
12 alphanumeric characters and is case sensitive.
Firmware Upgrade
This page allows you to upgrade the firmware of the
EnStationAC.
Account Settings
To Perform the Firmware Upgrade:
1. Click the Choose File button and navigate the OS file
system to the location of the upgrade file.
Administrator Username: Enter a new username for
logging in to the New Name entry box.
2. Select the upgrade file. The name of the file will appear
in the Upgrade File field.
Current Password: Enter the old password for logging in
to the Old Password entry box.
3. Click the Upload button to commence the firmware
upgrade.
New Password: Enter the new password for logging in to
the New Password entry box.
Note: The device is unavailable during the Firmware
upgrade process and must restart when the upgrade is
completed. Any connections to or through the device
will be lost.
Verify Password: Re-enter the new password in the
Confirm Password entry box for confirmation.
Apply: Click Apply to apply the changes.
60
Backup/Restore
Backup/Restore
Backup Setting: Click Export to save the current
configured settings.
This page allows you to save the current device
configurations. When you save your configurations,
you also can reload the saved configurations into the
device through the Restore Saved Settings from a file
section. If extreme problems occur, or if you have set
the AP incorrectly, you can use the Reset button in the
Revert to Factory Default Settings section to restore
all the configurations of the AP to the original default
settings.
Restore New Setting: To restore settings that have
been previously backed up, click Browse, select the
file, and click Restore.
Restore to Default: Click Reset button to restore the
AP to its factory default settings.
61
User Setting
Back Up Setting as Default: Click Backup to backup
the user settings you would like to the device’s memory
for the default settings.
The function allows you to backup the current device
configurations into the EnStationAC as the default
value. If extreme problems occur, or if you have set the
EnStationAC incorrectly, you can push the Reset button
to revert all the configurations of the EnStationAC to
the user default.
Restore to User Default: Click Restore to restore user
settings to the factory standard settings.
Note1: After setting the current settings as the default, you should click the Restore to Default on the
web interface for reverting the settings into the factory default instead of pushing the reset button.
Note2: Please write down your account and password before saving. The user settings will now become
the new default settings at the next successful login.
62
Log
System Log
Remote Log
The EnStationAC automatically logs (records) events
of possible interest in its internal memory. To view the
logged information, click the Log link under the System
Manager menu. If there is not enough internal memory
to log all events, older events are deleted from the log.
When powered down or rebooted, the log will be cleared.
This page allows you to setup the Remote Log functions
for the EnStationAC.
Syslog: Enables or disables the syslog function.
Log Server IP Address: Enter the IP address of the log
server.
Remote Log: Enable or disable the remote log service.
Apply: Click Apply to apply the changes.
63
Logout
Reset
Click Logout in Management menu to logout.
In some circumstances, it may be required to force the
device to reboot. Click on Reset to reboot or to reset the
EnStationAC.
64
Appendix
65
Appendix A
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that  to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT NOTE:
Radiation Exposure Statement
EnStationAC: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 26 cm between the radiator & your body.
EnStation5-AC: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 25 cm between the radiator & your body.
66
Appendix B - CE Interference Statement
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order
to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
• EN60950-1
		 Safety of Information Technology Equipment
• EN50385
		 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure
to electromagnetic fields (0 Hz - 300 GHz)
• EN 300 328
		 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating
in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article
3.2 of the R&TTE Directive
• EN 301 893
		 Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of
the R&TTE Directive
• EN 301 489-1
		 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
• EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
67
This device is a 5GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France
and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting
up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP
in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
Česky [Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Dansk [Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti [Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
Español [Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales
y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική [Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
68
Français [French]
Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil] est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle
altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas
1999/ 5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių [Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Nederlands [Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti
oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar [Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovensko [Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Slovensky [Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Suomi [Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
69
Svenska [Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och
övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
70
Appendix C - Professional Installation Instruction
Installation Personal
This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The
general user shall not attempt to install or change the setting.
Installation Location
The product shall be installed at a location where the radiating antenna can be kept 25cm from nearby person in normal operation condition to
meet regulatory RF exposure requirement.
Internal Antenna
Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive
RF transmitting power which may lead to the violation of FCC limit and is prohibited.
Installation Procedure
Please refer to user’s manual for the detail.
Warning:
Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant
rules. The violation of the rule could lead to serious federal penalty.
71

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2017:06:02 09:15:41+08:00
Metadata Date                   : 2017:06:02 11:37:16+08:00
Modify Date                     : 2017:06:02 11:37:16+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:e0a8936f-1055-49de-9408-5dc5efabc8b6
Original Document ID            : xmp.did:C4416EC81C206811822AF00EF18081D8
Document ID                     : xmp.id:B49791FE3047E7118D0ED5F89F51F21D
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:58DFCAEFC646E7119639E294E9FB5671
Derived From Document ID        : xmp.did:6D53C1307B3FE711A3E5CB2C530C3A2E
Derived From Original Document ID: xmp.did:C4416EC81C206811822AF00EF18081D8
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2017:06:02 09:15:41+08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 71
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools