EnOcean PTM33XC 315 MHz Transmitter User Manual PTM 330 V0 80wip
EnOcean GmbH 315 MHz Transmitter PTM 330 V0 80wip
EnOcean >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1315881 |
| Application ID | 1/lju5i4MTNo37eRPkKYIw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 49.08kB (613466 bits) |
| Date Submitted | 2010-07-22 00:00:00 |
| Date Available | 2010-07-22 00:00:00 |
| Creation Date | 2010-05-10 10:55:10 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2010-05-10 10:55:10 |
| Document Title | Microsoft Word - PTM 330 User Manual V0.80wip.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | wolfgang.heller |
USER MANUAL V0.8 Transmitter Module PTM 33x / 33xC May 4, 2010 Observe precautions! Electrostatic sensitive devices! Patent protected: WO98/36395, DE 100 25 561, DE 101 50 128, WO 2004/051591, DE 103 01 678 A1, DE 10309334, WO 04/109236, WO 05/096482, WO 02/095707, US 6,747,573, US 7,019,241 EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications PTM 33x / 33xC User Manual V0.8 May 10, 2010 10:54 AM Page 1/20 USER MANUAL V0.8 PTM 33X / 33XC REVISION HISTORY The following major modifications and improvements have been made to the first version of this document: No Major Changes Published by EnOcean GmbH, Kolpingring 18a, 82041 Oberhaching, Germany www.enocean.com, info@enocean.com, phone ++49 (89) 6734 6890 © EnOcean GmbH All Rights Reserved Important! This information describes the type of component and shall not be considered as assured characteristics. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the EnOcean website: http://www.enocean.com. As far as patents or other rights of third parties are concerned, liability is only assumed for modules, not for the described applications, processes and circuits. EnOcean does not assume responsibility for use of modules described and limits its liability to the replacement of modules determined to be defective due to workmanship. Devices or systems containing RF components must meet the essential requirements of the local legal authorities. The modules must not be used in any relation with equipment that supports, directly or indirectly, human health or life or with applications that can result in danger for people, animals or real value. Components of the modules are considered and should be disposed of as hazardous waste. Local government regulations are to be observed. Packing: Please use the recycling operators known to you. By agreement we will take packing material back if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or that we are not obliged to accept, we shall have to invoice you for any costs incurred. © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 2/20 USER MANUAL V0.8 PTM 33X / 33XC TABLE OF CONTENT 1.1 1.2 1.3 1.4 1.5 FUNCTIONAL DESCRIPTION .......................................................................... 6 2.1 Block diagram............................................................................................. 6 2.2 Pin out....................................................................................................... 7 2.3 Pin Description and operational characteristics................................................. 7 2.4 Configuration Interface ................................................................................ 8 2.5 Absolute maximum ratings (non operating)..................................................... 9 2.6 Maximum Ratings (operating) ....................................................................... 9 2.7 Radio telegram ..........................................................................................10 2.7.1 Normal operation....................................................................................10 2.7.2 User defined operation ............................................................................11 2.8 Transmit timing..........................................................................................11 3.1 3.2 3.3 3.4 3.5 3.6 GENERAL DESCRIPTION ............................................................................... 4 Basic Functionality....................................................................................... 4 Technical Data ............................................................................................ 4 Physical Dimensions .................................................................................... 5 Environmental Conditions ............................................................................. 6 Ordering Information ................................................................................... 6 APPLICATIONS INFORMATION ......................................................................12 How to connect an energy harvester .............................................................12 How to generate an equivalent energy pulse ..................................................12 Antenna ....................................................................................................13 Layout recommendations.............................................................................14 Soldering information PTM 332/332C ............................................................15 Transmission range ....................................................................................16 AGENCY CERTIFICATIONS (in preparation) ....................................................17 4.1 CE approval ...............................................................................................17 4.2 FCC (United States) Certification ..................................................................18 4.3 IC (Industry Canada) Certification.................................................................20 © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 3/20 USER MANUAL V0.8 PTM 33X / 33XC GENERAL DESCRIPTION 1.1 Basic Functionality The radio transmitter module PTM 330 from EnOcean enables the implementation of wireless sensors and switches without batteries. Key applications are handheld remote controls or industrial switches. Functional Principle When an energy pulse is supplied (e.g. by ECO 200 from EnOcean) an RF telegram is transmitted including a unique 32-bit module ID, the polarity of the energy pulse, and the operating status of 4 digital inputs. The RPS telegram content can be configured if other content is needed. PTM 330 can be connected to ECO 200 via a contact spring. There are two meander structures on the PCB which allow usage of a rubber pad to set the level of two digital inputs. Alternatively PTM 330 can be mounted as an SMD component onto a host PCB. In this case energy supply pins and digital input pins are accessible via contact pads. Product variants PTM 330: 868MHz variant, pre-installed whip antenna, delivery in card board box PTM 332: 868MHz variant, no pre-installed antenna, delivery as tape & reel PTM 330C: 315MHz variant, pre-installed whip antenna, delivery in card board box PTM 332C: 315MHz variant, no pre-installed antenna, delivery as tape & reel 1.2 Technical Data Power supply ECO 200 or equivalent energy pulse Antenna pre-installed whip antenna PTM 330/330C external 50 Ohm or whip antenna PTM 332/332C Frequency 868.3 MHz (PTM 33x) / 315.0 MHz (PTM 33xC) Transmission power typ. 2 dBm at antenna base Data rate / Modulation type Telegram type 125 kbps / ASK RPS of type 2 (allows interpretation of operating two buttons simultaneously) Digital inputs Transmission range © 2009 EnOcean | www.enocean.com up to 200 m free field, up to 30 m indoor PTM 33x / 33xC User Manual V0.8 | Page 4/20 USER MANUAL V0.8 PTM 33X / 33XC 1.3 Physical Dimensions PCB dimensions © 2009 EnOcean | www.enocean.com 26.2 x 21.15 x 3.5 mm PTM 33x / 33xC User Manual V0.8 | Page 5/20 USER MANUAL V0.8 PTM 33X / 33XC 1.4 Environmental Conditions Operating temperature -25 °C … +85 °C Storage temperature -40 °C … +85 °C Storage temperature in Tape&Reel -20 °C … +50 °C Humidity 1.5 0% … 93% r.h., non-condensing Ordering Information Type Ordering Code PTM 330 S3001-A330 PTM 332 S3001-A332 PTM 330C S3031-A330 PTM 332C S3031-A332 Frequency 868.3 MHz 868.3 MHz 315.0 MHz 315.0 MHz FUNCTIONAL DESCRIPTION 2.1 Block diagram Note Whip antenna mounted Card board box No antenna mounted Tape & Reel Whip antenna mounted Card board box No antenna mounted Tape & Reel At power-up by an energy pulse at AC1, AC2 a DC voltage is provided to the internal micro controller. The microcontroller reads the polarity of the supply voltage pulse and the status of the digital inputs A0, A1, B0, B1. After that 3 identical radio telegrams calculated from the status of these inputs are transmitted. PTM33x CFG A0 A1 RF_WHIP B0 µC B1 RF GND GND RF_50 Polarity Detection AC1 AC2 © 2009 EnOcean | www.enocean.com Power Converter PTM 33x / 33xC User Manual V0.8 | Page 6/20 USER MANUAL V0.8 PTM 33X / 33XC 2.2 Pin out GND CFG 16 AC1 15 AC2 B0 14 GND GND 13 V+ B1 12 GND A0 11 RF_50 GND 10 GND A1 AC1 AC2 T1 T4 T3 T8 T6 AC2 T5 T7 T9 AC1 T2 RF_WHIP On back side of PCB 2.3 Pin Description and operational characteristics Symbol Function Characteristics GND V+ Ground connection For test purposes only O-Button Rocker B Must be connected to GND Do not connect Digital input, leave open or connect to GND Internal pull-up Digital input, leave open or connect to GND Internal pull-up Digital input, leave open or connect to GND Internal pull-up Digital input, leave open or connect to GND Internal pull-up Must be connected to GND when used with equivalent energy pulse instead of ECO 200 Internal pull-up ECO 200 or equivalent energy pulse ECO 200 or equivalent energy pulse Output for whip antenna 50 Ohm output for external antenna See 2.4 B0 I-Button Rocker B B1 O-Button Rocker A A0 I-Button Rocker A A1 CFG Activate VOFF comparator when connected to GND AC1 AC2 RF_WHIP RF_50 T1-9 Input for ECO 200 Input for ECO 200 RF output RF output Configuration Interface © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 7/20 USER MANUAL V0.8 PTM 33X / 33XC 2.4 Configuration Interface Via the programming interface the telegram content can be modified. The interface is shown in the figure below: USB USB <= > SPI interface Dolphin Studio, or EOPx SPI Reset PROG_EN ADIO7 SCSEDIO0 SCLKDIO1 WSDADIO2 RSDADIO3 PTM 330 EnOcean provides EOPx (EnOcean Programmer, a command line program) and Dolphin Studio (Windows application for chip configuration, programming, and testing) and the USB/SPI programmer device as part of the EDK 300 developer’s kit. Pin Symbol Function Characteristics T1 T2 T3 T4 T5 T6 VDD GND SCSEDIO0 SCLKDIO1 WSDADIO2 RSDADIO3 RESET Supply voltage Ground connection SPI chip select SPI serial clock SPI input SPI output Reset Interface to programmer Interface to programmer Interface to programmer Interface to programmer Interface to programmer Interface to programmer Interface to programmer, internal pull down ADIO7 Sync output T7 T8 T9 PROG_EN © 2009 EnOcean | www.enocean.com Enable programming mode Interface to programmer HIGH: programming mode active LOW: operating mode Internal pull-down PTM 33x / 33xC User Manual V0.8 | Page 8/20 USER MANUAL V0.8 PTM 33X / 33XC 2.5 Absolute maximum ratings (non operating) Symbol AC1 AC2 GND A0 A1 B0 B1 2.6 Parameter Supply voltage Ground connection Min Max 6.4 Units Voltage digital input pins Maximum Ratings (operating) Symbol AC1 AC2 GND A0 A1 B0 B1 Parameter Supply voltage Ground connection Min Max 6.0 Units Voltage digital input pins © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 9/20 USER MANUAL V0.8 PTM 33X / 33XC 2.7 Radio telegram 2.7.1 Normal operation In default configuration PTM 33x transmits the same telegrams as a PTM 200 radio switch: Telegram type RPS: There are two message types depending on how many buttons (A0, A1, B0, B1) have been pressed (connected to GND) o N-message: Only one or two buttons have been pressed. o U-message: No pushbutton was pressed when activating the energy generator, or more than two pushbuttons have been pressed. Unique factory programmed 32 bit ID DATA_BYTE2, DATA_BYTE1, DATA_BYTE0=0 DATA_BYTE3 and STATUS as follows: N-message: DATA_BYTE3: RID UD RID UD PO SRID SUD SA PR (2 (1 (1 (2 (1 (1 bit) bit) bit) bit) bit) bit) SRID SUD SA Rocker ID, A=0, B=1 UD=1 Æ O-button, UD=0 Æ I-button Polarity, see table below Second Rocker ID (Second) SUD=1 Æ O-button, SUD=0 Æ I-button SA=1 Æ Second action (2 buttons pressed simultaneously), SA=0 Æ No second action STATUS: Reserved T21 Reserved T21 NU RP_COUNTER NU (2 (1 (1 (4 bit) bit) bit) bit) © 2009 EnOcean | www.enocean.com RP_COUNTER For future use NU=1 Æ N-message. Repeater level: 0 is original message (not repeated) PTM 33x / 33xC User Manual V0.8 | Page 10/20 USER MANUAL V0.8 PTM 33X / 33XC U-message: DATA_BYTE3: BUTTONS BUTTONS PR Reserved (3 bit) Number of simultaneously pressed buttons, as following: 0 = 0 Button 1 = not possible 2 = not possible 3 = 3 or 4 buttons 4 = not possible 5 = not possible 6 = not possible 7 = not possible PO Reserved (1 bit) (4 bit) Polarity, see table below STATUS: Reserved T21 Reserved T21 NU RP_COUNTER NU (2 (1 (1 (4 RP_COUNTER bit) bit) bit) bit) For future use NU=0 Æ U-message. Repeater level: 0 is original message (not repeated) The polarity PO is defined as follows: AC1 AC2 PO 2.7.2 User defined operation Via the configuration interface it is possible to define different content of DATA_BYTE3 and define if a N-message or U-message shall be sent. This allows for example to transmit other ORG=5 telegrams, e.g. “Mechanical handle”, as described in the EnOcean Equipment Profiles defined by EnOcean Alliance. 2.8 Transmit timing The setup of the transmission timing allows avoiding possible of other EnOcean transmitters as well as disturbances from transmission cycle, 3 identical subtelegrams are transmitted sion of a subtelegram lasts approximately 0.7 ms. The delay sion bursts is affected at random. © 2009 EnOcean | www.enocean.com collisions with data packages the environment. With each within 40 ms. The transmisbetween the three transmis- PTM 33x / 33xC User Manual V0.8 | Page 11/20 USER MANUAL V0.8 PTM 33X / 33XC APPLICATIONS INFORMATION 3.1 How to connect an energy harvester PTM 330 can be connected to ECO 200 without soldering. ECO 200 provides contact springs which can directly be connected to contact pads of PTM 330. The contact pads on the bottom of the PCB are shown below (left). A second orientation where PTM 330 is rotated 180° with respect to ECO 200 is also possible as shown with dashed lines. 3.2 How to generate an equivalent energy pulse © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 12/20 USER MANUAL V0.8 PTM 33X / 33XC 3.3 Antenna 315 MHz Option 1: 150 mm wire, connect to RF_WHIP Option 2: A 50Ω antenna can be connected to RF_50. In this case the limited modular FCC/IC approval is not valid! An FCC/IC approval is then needed for the end device! 868 MHz Option 1: 87 mm wire, connect to RF_WHIP Option 2: A 50 Ω antenna can be connected to RF_50 Specification of the whip antenna; L=150 mm @ 315 MHz, L=87 mm @ 868 MHz © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 13/20 USER MANUAL V0.8 PTM 33X / 33XC 3.4 Layout recommendations Proposal for foot print on host PCB Keep out area on host PCB. No copper surface area allowed! © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 14/20 USER MANUAL V0.8 PTM 33X / 33XC 3.5 Soldering information PTM 332/332C PTM 332 has to be soldered according to IPC/JEDEC J-STD-020C standard. PTM 332 shall be handled according to Moisture Sensitivity Level MSL4 which means a floor time of 72 h. PTM 332 may be soldered only once, since one time is already consumed at production of the module itself. Once the dry pack bag is opened, the desired quantity of units should be removed and the bag resealed within two hours. If the bag is left open longer than 30 minutes the desiccant should be replaced with dry desiccant. If devices have exceeded the specified floor life time of 72 h, they may be baked according IPC/JEDEC J-STD-033B. Devices packaged in moisture-proof packaging should be stored in ambient conditions not exceeding temperatures of 40 °C or humidity levels of 90% r.h.. PTM 332 modules have to be soldered within 6 months after delivery! © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 15/20 USER MANUAL V0.8 PTM 33X / 33XC 3.6 Transmission range The main factors that influence the system transmission range are type and location of the antennas of the receiver and the transmitter, type of terrain and degree of obstruction of the link path, sources of interference affecting the receiver, and “Dead” spots caused by signal reflections from nearby conductive objects. Since the expected transmission range strongly depends on this system conditions, range tests should categorically be performed before notification of a particular range that will be attainable by a certain application. The following figures for expected transmission range are considered by using a PTM, a STM or a TCM radio transmitter device and the TCM radio receiver device with preinstalled whip antenna and may be used as a rough guide only: Line-of-sight connections: Typically 30 m range in corridors, up to 100 m in halls Plasterboard walls / dry wood: Typically 30 m range, through max. 5 walls Line-of-sight connections: Typically 30 m range in corridors, up to 100 m in halls Ferroconcrete walls / ceilings: Typically 10 m range, through max. 1 ceiling Fire-safety walls, elevator shafts, staircases and supply areas should be considered as screening. The angle at which the transmitted signal hits the wall is very important. The effective wall thickness – and with it the signal attenuation – varies according to this angle. Signals should be transmitted as directly as possible through the wall. Wall niches should be avoided. Other factors restricting transmission range: Switch mounted on metal surfaces (up to 30% loss of transmission range) Hollow lightweight walls filled with insulating wool on metal foil False ceilings with panels of metal or carbon fiber Lead glass or glass with metal coating, steel furniture The distance between EnOcean receivers and other transmitting devices such as computers, audio and video equipment that also emit high-frequency signals should be at least 0.5 m A summarized application note to determine the transmission range within buildings is available as download from www.enocean.com. © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 16/20 USER MANUAL V0.8 PTM 33X / 33XC AGENCY CERTIFICATIONS (in preparation) The modules have been tested to fulfil the approval requirements for CE (PTM 33x) and FCC/IC (PTM 33xC) based on the built-in firmware. 4.1 CE approval The modules bear the EC conformity marking CE and conforms to the R&TTE EU-directive on radio equipment. The assembly conforms to the European and national requirements of electromagnetic compatibility. The conformity has been proven and the according documentation has been deposited at EnOcean. The modules can be operated without notification and free of charge in the area of the European Union, and in Switzerland. The following provisos apply: • • • • • EnOcean RF modules must not be modified or used outside their specification limits. EnOcean RF modules may only be used to transfer digital or digitized data. Analog speech and/or music are not permitted. The final product incorporating EnOcean RF modules must itself meet the essential requirement of the R&TTE Directive and a CE marking must be affixed on the final product and on the sales packaging each. Operating instructions containing a Declaration of Conformity has to be attached. If the transmitter is used according to the regulations of the 868.3 MHz band, a so-called “Duty Cycle” of 1% per hour must not be exceeded. Permanent transmitters such as radio earphones are not allowed. The module must be used with only the following approved antenna(s). Type Parameter Value Wire/Monopole at RF_WHIP Maximum gain 1.0 dBi External antenna at RF_50 Antenna type Passive Impedance ~50 Ohm Maximum gain ≤ 0 dBd © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 17/20 USER MANUAL V0.8 PTM 33X / 33XC 4.2 FCC (United States) Certification PTM330C and PTM332C LIMITED MODULAR APPROVAL This is an RF module approved for Limited Modular use operating as an intentional transmitting device with respect to 47 CFR 15.231(a-c) and is limited to OEM installation. The module is optimized to operate using small amounts of energy, and may be powered by a battery. The module transmits short radio packets comprised of control signals, (in some cases the control signal may be accompanied with data) such as those used with alarm systems, door openers, remote switches, and the like. The module does not support continuous streaming of voice, video, or any other forms of streaming data; it sends only short packets containing control signals and possibly data. The module is designed to comply with, has been tested according to 15.231(a-c), and has been found to comply with each requirement. Thus, a finished device containing the PTM330C/PTM332C radio module can be operated in the United States without additional Part 15 FCC approval (approval(s) for unintentional radiators may be required for the OEM’s finished product), under EnOcean’s FCC ID number. This greatly simplifies and shortens the design cycle and development costs for OEM integrators. The module can be triggered manually or automatically, which cases are described below. Manual Activation The radio module can be configured to transmit a short packetized control signal if triggered manually. The module can be triggered, by pressing a switch, for example. The packet contains one (or more) control signals that is(are) intended to control something at the receiving end. The packet may also contain data. Depending on how much energy is available from the energy source, subsequent manual triggers can initiate the transmission of additional control signals. This may be necessary if prior packet(s) was(were) lost to fading or interference. Subsequent triggers can also be initiated as a precaution if any doubt exists that the first packet didn’t arrive at the receiver. Each packet that is transmitted, regardless of whether it was the first one or a subsequent one, will only be transmitted if enough energy is available from the energy source. Automatic Activation The radio module also can be configured to transmit a short packetized control signal if triggered automatically. Again, the packet contains a control signal that is intended to control something at the receiving end and may also contain data. As above, it is possible for the packet to get lost and never reach the receiver. However, if enough energy is available from the energy source, and the module has been configured to do so, then another packet or packets containing the control signal may be transmitted at a later time. OEM Requirements In order to use EnOcean’s FCC ID number, the OEM must ensure that the following conditions are met: End users of products, which contain the module, must not have the ability to alter the firmware that governs the operation of the module. The agency grant is valid only when the module is incorporated into a final product by OEM integrators. The end-user must not be provided with instructions to remove, adjust or install the module. © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 18/20 USER MANUAL V0.8 PTM 33X / 33XC The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the final product. Attaching a label to a removable portion of the final product, such as a battery cover, is not permitted. The label must include the following text: Contains FCC ID: SZV-PTM33XC The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any interference received, including interference that may cause undesired operation. The user manual for the end product must also contain the text given above. Changes or modifications not expressly approved by EnOcean could void the user's authority to operate the equipment. The module must be used with only the following approved antenna(s). Part Number N.A. Type Wire/Monopole Gain 1.0 dBi The OEM must ensure that timing requirements according to 47 CFR 15.231(a-c) are met. The OEM must sign the OEM Limited Modular Approval Agreement with EnOcean © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 19/20 USER MANUAL V0.8 PTM 33X / 33XC 4.3 IC (Industry Canada) Certification In order to use EnOcean’s IC number, the OEM must ensure that the following conditions are met: Labeling requirements for Industry Canada are similar to those required by the FCC. The Original Equipment Manufacturer (OEM) must ensure that IC labeling requirements are met. A clearly visible label on the outside of a non-removable part of the final product must include the following text: Contains IC: 5713A-PTM33XC The OEM must sign the OEM Limited Modular Approval Agreement with EnOcean © 2009 EnOcean | www.enocean.com PTM 33x / 33xC User Manual V0.8 | Page 20/20
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 20 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:bb6785a0-389f-4185-98aa-a0aca948b756 Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2010:05:10 10:55:10+02:00 Create Date : 2010:05:10 10:55:10+02:00 Document ID : uuid:ff302bc7-1f8c-4de2-955c-38ea3d0fb496 Format : application/pdf Title : Microsoft Word - PTM 330 User Manual V0.80wip.doc Creator : wolfgang.heller Author : wolfgang.hellerEXIF Metadata provided by EXIF.tools