EnOcean STM300U TRANSCEIVER MODULE User Manual 3

Download:
Mirror Download [FCC.gov]
Document ID	1908333
Application ID	ydUd0Fxu0+UIca3w9kJLEA==
Document Description	User Manual 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	85.42kB (1067718 bits)
Date Submitted	2013-02-27 00:00:00
Date Available	2013-02-27 00:00:00
Creation Date	2017-10-28 07:44:12
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-28 07:44:12
Document Title	User Manual 3
Document Creator	Microsoft® Office Word 2007
Document Author:	WH / MK

USER MANUAL
V1.07
Transceiver Module
TCM 310 / TCM 310C / TCM 310U
February 14th, 2013
Observe precautions! Electrostatic sensitive devices!
Patent protected:
WO98/36395, DE 100 25 561, DE 101 50 128,
WO 2004/051591, DE 103 01 678 A1, DE 10309334,
WO 04/109236, WO 05/096482, WO 02/095707,
US 6,747,573, US 7,019,241
EnOcean GmbH
Kolpingring 18a
82041 Oberhaching
Germany
Phone +49.89.67 34 689-0
Fax
+49.89.67 34 689-50
info@enocean.com
www.enocean.com
Subject to modifications
TCM 310 / 310C / TCM 310U User Manual
February 14, 2013
Page 1/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
REVISION HISTORY
The following major modifications and improvements have been made to the first version of
this document:
No
1.00
1.01
1.02
1.03
1.04
1.05
1.06
1.07
Major Changes
Initial version
Modification for Step Code DB; increased number of filters and Smart Ack mailboxes
Supply voltage range extended
Start-up time and current consumption in deep sleep mode added in 1.2; improved layout recommendations in 3.5
Antenna recommendations removed and referred to application note AN102 and
AN105; Maximum Rating for IOVDD modified (IOVDD may now exceed VDD); Additional information in 3.6; Chapter “Related Documents” added; pin numbers
added in 3.2; update of FCC grant in 5.2; parameters for antenna requirements
relaxed in 4.2.1.;
Error in table in 3.2 corrected (pin 17 and 18 need to be connected to GND as
shown in figure above)
Supply voltage range extended; start-up time from sleep added
Added TCM 310U
Published by EnOcean GmbH, Kolpingring 18a, 82041 Oberhaching, Germany
www.enocean.com, info@enocean.com, phone +49 (89) 6734 6890
© EnOcean GmbH
All Rights Reserved
Important!
This information describes the type of component and shall not be considered as assured characteristics. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications
are subject to change without notice. For the latest product specifications, refer to the EnOcean website: http://www.enocean.com.
As far as patents or other rights of third parties are concerned, liability is only assumed for modules,
not for the described applications, processes and circuits.
EnOcean does not assume responsibility for use of modules described and limits its liability to the
replacement of modules determined to be defective due to workmanship. Devices or systems containing RF components must meet the essential requirements of the local legal authorities.
The modules must not be used in any relation with equipment that supports, directly or indirectly,
human health or life or with applications that can result in danger for people, animals or real value.
Components of the modules are considered and should be disposed of as hazardous waste. Local
government regulations are to be observed.
Packing: Please use the recycling operators known to you.
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 2/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
TABLE OF CONTENT
MODULE VARIANTS AND RELATED DOCUMENTS ............................................... 4
2.1
2.2
2.3
2.4
2.5
GENERAL DESCRIPTION ................................................................................. 4
Basic functionality ......................................................................................... 4
Technical data............................................................................................... 5
Physical dimensions ....................................................................................... 6
Environmental conditions ............................................................................... 6
Ordering information ..................................................................................... 6
FUNCTIONAL DESCRIPTION ............................................................................ 7
3.1 Pin out ......................................................................................................... 7
3.2 Pin description and operational characteristics .................................................. 7
3.2.1 GPIO supply voltage - IOVDD ...................................................................... 8
3.3 Absolute maximum ratings (non operating) ...................................................... 8
3.4 Maximum ratings (operating) .......................................................................... 8
3.5 System environment ...................................................................................... 8
3.6 Serial Interface ............................................................................................. 9
3.7 Built-in Repeater ......................................................................................... 10
3.8 Smart Acknowledge ..................................................................................... 10
3.9 Remote Management ................................................................................... 11
APPLICATIONS INFORMATION....................................................................... 11
4.1 Transmission range ..................................................................................... 11
4.2 Antenna options .......................................................................................... 12
4.2.1 Overview ................................................................................................ 12
4.2.2 Whip antenna ......................................................................................... 12
4.2.3 Helical antenna ....................................................................................... 13
4.3 Recommendations for laying a whip antenna .................................................. 14
4.4 Power supply requirements ........................................................................... 15
4.5 Layout recommendations ............................................................................. 15
4.5.1 Recommended foot pattern ....................................................................... 16
4.6 Soldering information .................................................................................. 19
4.7 Tape & Reel specification .............................................................................. 20
5.1
5.2
5.3
5.4
5.5
AGENCY CERTIFICATIONS ............................................................................ 21
CE approval ................................................................................................ 21
FCC (United States) Certification ................................................................... 22
IC (Industry Canada) Certification ................................................................. 24
FCC Regulatory Statements............................................................................... 25
Industry Canada Regulatory Statements ................................................................ 26
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 3/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
MODULE VARIANTS AND RELATED DOCUMENTS
This document describes operation of TCM 310 modules available in variations for following
frequencies:
 TCM 310 :
 TCM 310C:
 TCM 310U:
868.300 MHz
315.000 MHz
902.875 MHz
In side this manual the following terms TCM310x can be used interchangeably for any of
the above frequency.
This document describes operation of TCM 310x modules with their built-in firmware.
In addition we recommend following our application notes, in particular
 AN101: Power Supply Layout – Layout considerations for Line-Power
 AN102: Antenna Basics – Basic Antenna Design Considerations for EnOcean based
Products
 AN105: 315 MHZ Internal Antenna Design – Considerations for EnOcean based Products
The specification of the serial protocol ESP3 can be found here:
http://www.enocean.com/en/enocean_modules/tcm-310/
2.1
GENERAL DESCRIPTION
Basic functionality
TCM 310x is a SMD mountable radio transmitter module enabling the realization of gateways for EnOcean
868 MHz, 315 MHz and 902 MHz radio systems. It provides a bi-directional radio interface and a bidirectional serial interface. Radio messages are sent
transparently through the serial interface in both directions from and to an externally connected host processor or host PC. In addition control commands can be
sent from the host, e.g. to configure the repeater functionality or to manage Smart Ack functions. TCM 310x
can act as postmaster for up to 20 bi-directional sensors using Smart Ack technology.
Features
 Smart Ack controller functionality
 Transparent radio channel
 Programmable repeater functionality (1 / 2 Level)
 ESP3 support (EnOcean Serial Protocol V3)
 Not API programmable!
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 4/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
2.2
Technical data
Antenna
Frequency
Radio Standard
Data rate/Modulation type
Receiver Sensitivity (at 25°C)
Conducted Output Power
Power Supply
Serial Interface
Current Consumption
Dimensions of PCB
Operating temperature
Radio Regulations
1) According to ISO/IEC 14543-3-10
© 2013 EnOcean | www.enocean.com
TCM 310 : external whip or 50Ω antenna mountable
TCM 310C:
external whip
TCM 310U:
external whip or Helical antenna
TCM 310 : 868.300 MHz (ASK)1)
TCM 310C: 315.000 MHz (ASK)1)
TCM 310U: 902.875 MHz (FSK)
Enocean 868 MHz/315 MHz: ISO/IEC 14543-3-10
125 kbps
typ. –96 dBm (868.300 MHz) 2)
typ. -98 dBm (315.000 MHz) 2)
typ. -98 dBm (902.875 MHz) 2)
typ. 3 dBm @ 313 and 868 MHz / 1dBm @ 902.875 MHz
2.85…3.5V
UART
Receive mode: 33 mA
Transmit mode: 24 mA
22x19x3 mm
0 to +65°C
R&TTE EN 300 220 (TCM 310)
FCC CFR-47 Part 15 (TCM 310C / TCM 310U)
2) @ 0.1% telegram error rate based on transmitted sub-telegrams
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 5/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
2.3
Physical dimensions
Unless otherwise specified dimensions are in mm.
Tolerances:
PCB outline dimensions 0.2 mm
All other tolerances 0.1 mm
TCM 310 (pads on bottom side of PCB!)
22 x 19 x 3.1 mm
PCB Dimension
1.9 g
Weight
2.4
Environmental conditions
-0 °C … +65 °C
Operating temperature
Storage temperature
-40 °C … +85 °C
Storage temperature in tape & reel package
-20 °C … +50 °C
0% … 93% r.H., non-condensing
Humidity
2.5
Ordering information
Type
TCM 310
TCM 310C
TCM 310U
Ordering Code
S3003-K310
S3033-K310
S3053-K310
© 2013 EnOcean | www.enocean.com
Frequency
868.300 MHz
315.000 MHz
902.875 MHz
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 6/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
FUNCTIONAL DESCRIPTION
GND
GND
RESET
GND
n.c.
n.c.
GND
n.c.
Pin out
n.c.
3.1
n.c.
26
DVDD
VDD
XTAL
16MHz
n.c.
GND
IOVDD
Antenna
balun
n.c.
EO3000I
RF_WHIP
n.c.
GND
n.c.
RF_50
TCM310/310C
TOP VIEW
GND
18
GND
GND
SER_TX
SER_RX
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
RVDD
n.c.
The figure above shows the pin out of the TCM 310x hardware.
3.2
Pin description and operational characteristics
HW Symbol
Pin #
GND
1, 5, 7, 17, 18, Ground connection
24, 26, 28, 31
Supply voltage
RF supply voltage
regulator output
25
Digital supply voltage
regulator output
23
GPIO supply voltage
VDD
RVDD
DVDD
IOVDD
RESET
SER_RX
SER_TX
RF_WHIP
RF_50
n.c.
27
15
16
3, 9-14, 19-22,
29,30, 32-34
© 2013 EnOcean | www.enocean.com
Function
Reset input
UART input
UART output
RF output
RF output
Not connected
Characteristics
Must be connected to GND; see 4.4
2.6 V … 3.5 V
Leave open
1.8 V
Output current: max. 5 mA
Must be connected to desired interface supply voltage (see 3.4) See
also 3.2.1.
External 10 kΩ pull-down required.
See 3.6
See 3.6
Output for whip antenna
50 Ohm output for external antenna
Do not connect!
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 7/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
3.2.1 GPIO supply voltage - IOVDD
For digital communication with other circuitry the pins of the serial interface UART may be
operated from supply voltages different from DVDD. Therefore an interface voltage supply
pin IOVDD is available which must be connected either to DVDD or to an external supply
within the tolerated voltage range of IOVDD.
If DVDD=0 V (e.g. in any sleep mode or if VDD 6 dB
Important for compatibility with EnOcean protocol
Bandwidth
≤ 20 MHz
Important if 10 V/m EMI robustness required for device
For 315 MHz / 902.875 MHz modules (TCM 310C / TCM 310U) please note
that a full approval is needed if modules are used with antennas other than
the specified antennas.
4.2.2 Whip antenna
315 MHz
Antenna: 150 mm wire, connect to RF_WHIP
Minimum GND plane: 50 mm x 50 mm
Minimum distance space: 10 mm
868.3 MHz
Antenna: 86 mm wire, connect to RF_WHIP
Minimum GND plane: 38 mm x 18 mm
Minimum distance space: 10 mm
902.875
Antenna:
Minimum
Minimum
MHz
64 mm wire, connect to RF_WHIP
GND plane: 50 mm x 50 mm
distance space: 10 mm
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 12/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
4.2.3 Helical antenna
315 MHz
please contact EnOcean for availability
868.3 MHz
according to drawing below, connect to RF_WHIP
please contact EnOcean for MOQ
Minimum GND plane: 35 mm x 30 mm
Minimum distance space: 10 mm
902.875 MHz
limited modular approval available
please contact EnOcean for MOQ and mandatory limited modular approval user agreement
according to drawing below, connect to RF_WHIP
Minimum GND plane: 35 mm x 30 mm
Minimum distance space: 10 mm
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 13/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
4.3
Recommendations for laying a whip antenna

PCB with GND
PCB without GND
Antenna too close
to GND area


Antenna end led
back to foot point
Antenna too close
to GND area

© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 14/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
4.4
Power supply requirements
In order to provide a good radio performance, great attention must be paid to the power
supply and a correct layout and shielding. It is recommended to place a 22 µF ceramic capacitor between VDD and GND close to the module (material: X5R, X7R, min 6.3 V to avoid
derating effects). In addition a 470 nH coil shall be inserted (Murata LQW18A, 0603) in the
power supply line.
For best performance it is recommended to keep the ripple on the power supply rail below
10 mVpp (see 3.4).
All GND pins must be connected to GND. Be careful not to create loops! The
ground must be realized ideally on both sides of the PCB board with many vias. At
least there must be a short star connection. Otherwise RF performance can be
reduced!
4.5
Layout recommendations
The length of lines connected to I/Os should not exceed 5 cm.
It is recommended to have a complete GND layer in the application PCB, at least
in the area below the module and directly connected components (e.g. mid-layer
of your application PCB).
Due to unisolated test points there are live signals accessible on the bottom side
of the module.
Please follow the following advices to prevent interference with your application
circuit:

We suggest avoiding any copper structure in the area directly underneath
the module (top-layer layout of your application PCB). If this is not possible
in your design, please provide coating on top of your PCB to prevent short
circuits to the module. All bare metal surfaces including vias have to be
covered (e.g. adequate layout of solder resist).

It is mandatory that the area marked by the circle in the figure below is
kept clear of any conductive structures in the top layer and 0.3 mm below.
Otherwise RF performance will be degraded!
Furthermore, any distortive signals (e.g. bus signals or power lines) should not be
routed underneath the module. If such signals are present in your design, we suggest separating them by using a ground plane between module and these signal
lines.
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 15/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
4.5.1 Recommended foot pattern
Top layer
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 16/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
Solder resist top layer
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 17/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
Solder paste top layer
The data above are also available as EAGLE library.
In order to ensure good solder quality a solder mask thickness of 150 µm is recommended.
In case a 120 µm solder mask is used, it is recommended to enlarge the solder print. The
pads on the solder print should then be 0.1 mm larger than the pad dimensions of the
module as specified in chapter 2.3. (not relative to the above drawing).
Nevertheless an application and production specific test regarding the amount of soldering
paste should be performed to find optimum parameters.
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 18/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
4.6
Soldering information
TCM 310x shall be soldered according to IPC/JEDEC J-STD-020C standard.
TCM 310 shall be handled according to Moisture Sensitivity Level MSL4 which means a floor
time of 72 h. TCM 310 may be soldered only once, since one time is already consumed at
production of the module itself.
Once the dry pack bag is opened, the desired quantity of units should be removed and the
bag resealed within two hours. If the bag is left open longer than 30 minutes the desiccant
should be replaced with dry desiccant. If devices have exceeded the specified floor life time
of 72 h, they may be baked according IPC/JEDEC J-STD-033B at max. 90°C for less than
60 h.
Devices packaged in moisture-proof packaging should be stored in ambient conditions not
exceeding temperatures of 40 °C or humidity levels of 90% r.H.
TCM 310x modules shall be soldered within 6 months after delivery!
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 19/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
4.7
Tape & Reel specification
Tape running direction
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 20/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
AGENCY CERTIFICATIONS
The modules have been tested to fulfil the approval requirements for CE (TCM 310) and
FCC/IC (TCM 310C / TCM 310U) based on the built-in firmware.
5.1
CE approval
The modules bear the EC conformity marking CE and conform to the R&TTE EU-directive on
radio equipment. The assembly conforms to the European and national requirements of
electromagnetic compatibility. The conformity has been proven and the according documentation has been deposited at EnOcean. The modules can be operated without notification and free of charge in the area of the European Union, and in Switzerland. The following
provisos apply:





EnOcean RF modules must not be modified or used outside their specification
limits.
EnOcean RF modules may only be used to transfer digital or digitized data.
Analog speech and/or music are not permitted.
The final product incorporating EnOcean RF modules must itself meet the essential requirement of the R&TTE Directive and a CE marking must be affixed
on the final product and on the sales packaging each. Operating instructions
containing a Declaration of Conformity has to be attached.
If the transmitter is used according to the regulations of the 868.3.3 MHz
band, a so-called “Duty Cycle” of 1% per hour must not be exceeded. Permanent transmitters such as radio earphones are not allowed.
The module must be used with only the following approved antenna(s).
Type
Parameter
Value
Wire/Monopole at RF_WHIP Maximum gain
1.0 dBi
External antenna at RF_50
Antenna type
Passive
Impedance
~50 Ohm
Maximum gain
≤ 0 dBd
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 21/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
5.2
FCC (United States) Certification
TCM 310C / TCM 310U LIMITED MODULAR APPROVAL
This is an RF module approved for Limited Modular use operating as an intentional transmitting device with respect to 47 CFR 15.231(a-c) and is limited to OEM installation. The
module is optimized to operate using small amounts of energy, and may be powered by a
battery. The module transmits short radio packets comprised of control signals, (in some
cases the control signal may be accompanied with data) such as those used with alarm systems, door openers, remote switches, and the like. The module does not support continuous streaming of voice, video, or any other forms of streaming data; it sends only short
packets containing control signals and possibly data. The module is designed to comply
with, has been tested according to 15.231(a-c), and has been found to comply with each
requirement. Thus, a finished device containing the TCM 310C / TCM 310U radio module
can be operated in the United States without additional Part 15 FCC approval (approval(s)
for unintentional radiators may be required for the OEM’s finished product), under EnOcean’s FCC ID number. This greatly simplifies and shortens the design cycle and development costs for OEM integrators. The module can be triggered manually or automatically,
which cases are described below.
Manual Activation
The radio module can be configured to transmit a short packetized control signal if triggered manually. The module can be triggered, by pressing a switch, for example.
The packet contains one (or more) control signals that is(are) intended to control something at the receiving end. The packet may also contain data. Depending on how much energy is available from the energy source, subsequent manual triggers can initiate the
transmission of additional control signals. This may be necessary if prior packet(s)
was(were) lost to fading or interference. Subsequent triggers can also be initiated as a precaution if any doubt exists that the first packet didn’t arrive at the receiver. Each packet
that is transmitted, regardless of whether it was the first one or a subsequent one, will only
be transmitted if enough energy is available from the energy source.
Automatic Activation
The radio module also can be configured to transmit a short packetized control signal
if triggered automatically, by a relevant change of its inputs or in response to receiving a
signal from another transmitter, for example. Again, the packet contains a control signal
that is intended to control something at the receiving end and may also contain data. As
above, it is possible for the packet to get lost and never reach the receiver. However, if
enough energy is available from the energy source, and the module has been configured to
do so, then another packet or packets containing the control signal may be transmitted at a
later time.
The device is capable to operate as a repeater, which can receive signals from the following
list of FCC/IC approved transmitters, and retransmit the signals.











PTM 200C
STM 110C
TCM 200C
TCM 220C
TCM 300C
STM 300C
TCM 320C
PTM 210U
STM 300U
TCM 300U
TCM 320U
© 2013 EnOcean | www.enocean.com
FCC
FCC
FCC
FCC
FCC
FCC
FCC
FCC
FCC
FCC
FCC
ID:SZV-PTM200C
ID:SZV-STM110C
ID:SZV-TCM2XXC
ID:SZV-TCM2XXC
ID:SZV-STM300C
ID:SZV-STM300C
ID:SZV-TCM320C
ID:SZV-PTM210U
ID:SZV-STM300U
ID:SZV-STM300U
ID:SZV-TCM320U
IC:5713A-PTM200C
IC:5713A-STM110C
IC:5713A-TCM2XXC
IC:5713A-TCM2XXC
IC:5713A-STM300C
IC:5713A-STM300C
IC:5713A-TCM320C
IC:5713A-PTM210U
IC:5713A-STM300U
IC:5713A-STM300U
IC:5713A-TCM320U
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 22/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
OEM Requirements
In order to use EnOcean’s FCC ID number, the OEM must ensure that the following conditions are met:

End users of products, which contain the module, must not have the ability to alter the
firmware that governs the operation of the module. The agency grant is valid only when
the module is incorporated into a final product by OEM integrators.

The end-user must not be provided with instructions to remove, adjust or install the
module.

The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the final product.
Attaching a label to a removable portion of the final product, such as a battery cover, is
not permitted. The label must include the following text:
TCM 310C:
Contains FCC ID: SZV-STM300C
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (i.) this device may not cause harmful interference and
(ii.) this device must accept any interference received, including interference that
may cause undesired operation.
TCM 310U:
Contains FCC ID: SZV-STM300U
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (i.) this device may not cause harmful interference and
(ii.) this device must accept any interference received, including interference that
may cause undesired operation.
When the device is so small or for such use that it is not practicable to place the statement above on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC
identifier or the unique identifier, as appropriate, must be displayed on the device.
The user manual for the end product must also contain the text given above.

Changes or modifications not expressly approved by EnOcean could void the user's authority to operate the equipment.

The module must be used with only the following approved antenna(s).
Part Number
N.A.
N.A.
© 2013 EnOcean | www.enocean.com
Type
Wire/Monopole
Helical (for TCM300U only)
Gain
1.0 dBi
1.0 dBi
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 23/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U

The OEM must ensure that timing requirements according to 47 CFR 15.231(a-c) are
met.

The OEM must sign the OEM Limited Modular Approval Agreement with EnOcean
5.3
IC (Industry Canada) Certification
In order to use EnOcean’s IC number, the OEM must ensure that the following conditions
are met:
 Labeling requirements for Industry Canada are similar to those required by the FCC.
The Original Equipment Manufacturer (OEM) must ensure that IC labeling requirements
are met. A clearly visible label on the outside of a non-removable part of the final product must include the following text:
TCM 310C:
Contains IC: 5713A-STM300C
Contient le module d'émission IC: 5713A-STM300C
TCM 310U:
Contains IC: 5713A-STM300U
Contient le module d'émission IC: 5713A-STM300U
 The OEM must sign the OEM Limited Modular Approval Agreement with EnOcean
Pour utiliser le numéro IC EnOcean, le OEM doit s'assurer que les conditions suivantes sont
remplies:

Les exigences d'étiquetage pour Industrie Canada sont similaires à ceux exigés par la
FCC. Le fabricant d'équipement d'origine (OEM) doit s'assurer que les exigences en
matière d'étiquetage IC sont réunies. Une étiquette clairement visible à l'extérieur d'une
partie non amovible du produit final doit contenir le texte suivant:
TCM 310C:
Contains IC: 5713A-STM300C
Contient le module d'émission IC: 5713A-STM300C
TCM 310U:
Contains IC: 5713A-STM300U
Contient le module d'émission IC: 5713A-STM300U
 L'OEM doit signer l'accord OEM limitée Approbation modulaire avec EnOcean
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 24/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
5.4
FCC Regulatory Statements
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by manufacturer could void the user’s authority to operate the equipment.
IMPORTANT! Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 25/26
USER MANUAL
V1.07
TCM 310 / TCM 310C / TCM 310U
5.5
Industry Canada Regulatory Statements
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.
IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la
partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actioner cet
équipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
© 2013 EnOcean | www.enocean.com
TCM 310 / TCM 310C / TCM 310U User Manual V1.07 | Page 26/26

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : WH / MK
Create Date                     : 2013:02:14 15:12:49-07:00
Modify Date                     : 2013:02:15 09:03:48-07:00
Language                        : de-DE
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : WH / MK
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2013:02:15 09:03:48-07:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:7f4f3976-be7a-4309-a418-65a4cc289e00
Instance ID                     : uuid:3cfcf5ff-9425-4bb0-8888-f8bb81ae82de
Page Count                      : 26

EXIF Metadata provided by EXIF.tools