Encore Electronic Enh908 Nwy Users Manual ®

ENH908-NWY to the manual eeeb9b78-88f5-4eb4-83ef-1893d055c0a6

: Encore-Electronic Encore-Electronic-Enh908-Nwy-Users-Manual-540274 encore-electronic-enh908-nwy-users-manual-540274 encore-electronic pdf

Open the PDF directly: View PDF .
Page Count: 6

Download
Open PDF In Browser	View PDF

ENH908-NWY
8 Port Switch

User Guide

0

The ENH908-NWY is a powerful, high-performance Fast
Ethernet switch, with all ports capable of 10 or 100Mbps
auto-negotiation operation (NWay), which means the switch
could automatically negotiate with the connected partners on
the network speed and duplex mode. It is ideal for
micro-segmenting large networks into smaller, connected
subnets for improved performance, enabling the bandwidth
demanding multimedia and imaging applications. Compared
to the shared 10Mbps or 100Mbps networks, the switch
delivers a dedicated 10/100Mbps connection to every
attached client with no bandwidth congestion issue. This
switch also supports auto MDI / MDI-X function. Each port
could be used to connect to another switch or hub with no
crossover RJ-45 cable.
Store-and-forward switching mode promises the low latency
plus eliminates all the network errors, including runt and CRC
error packets. To work under full-duplex mode, transmission
and reception of the frames can occur simultaneously without
causing collisions as well as double the network bandwidth.
The switch is plug-n-play without any software to configure
and also fully compliant with all kinds of network protocols.
Moreover, the rich diagnostic LEDs on the front-panel can
provide the operating status of individual port and whole
system.
Before you start to install the switch, check the following
contents in this package：
z
z
z

One NWay switch
One external power adapter
User’s manual
1

Please refer to the following table for LED definition

8port

LED
Power

Status
Steady Green
Off
Link/Act Steady Green
Blinking Green
Off

Operation
Power is on
Power is off
The port is connected
The port is transmitting/receiving
data.
No connection

Rear Panel

8port

2

Connect each station to the switch by twisted-pair cable.
Plug one RJ-45 connector into a RJ-45 port of the switch,
and plug the other RJ-45 connector into the station’s network
adapter. Power on the switch and then system is ready.
For cable selection, refer to the following table.

In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As
all the ports support auto MDI / MDI-X function, using a
straight cable to make a switch-to-switch connection is
allowed.
For cable selection, refer to the following table：
Network Speed

Cable Type

10Mbps

Cat. 3, 4, 5 UTP/STP

100 meters

100Mbps

Cat. 5 UTP/STP

100 meters

3

Max. Length

Standard

IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x full duplex operation and flow
control

Interface

8* 10/100Mbps RJ-45 Fast Ethernet Ports

Uplink

Auto MDI/MDI-X（Auto crossover）

Network Speed

10/100Mbps & Full/Half duplex mode auto
detection

MAC Address
Table

1K MAC address entries

Memory

768KBytes (8port)

Power Supply

External Power adapter
5V DC 0.6A

EMI

CE, FCC

4

FCC Certifications
This Equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received; including interference that may cause undesired operation.

CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class A for ITE, the essential
protection requirement of Council Directive 89/336/EEC on the
approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may
be possible that information in this document is not up-to-date. Please
check with your local distributors for the latest information. No part of
this document can be copied or reproduced in any form without written
consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2008, All Rights Reserved.

5



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2008:07:10 16:33:30-07:00
Creator Tool                    : Acrobat PDFMaker 7.0.7 for Word
Modify Date                     : 2008:07:10 16:33:44-07:00
Metadata Date                   : 2008:07:10 16:33:44-07:00
Format                          : application/pdf
Title                           : ®
Creator                         : shogo
Document ID                     : uuid:c79a92f8-2d16-4f03-8a79-26d03bdaf4a5
Instance ID                     : uuid:695a9a35-799c-40f9-8275-5883a835418f
Company                         : 
Source Modified                 : D:20080710233319
Page Count                      : 6
Page Layout                     : OneColumn
Author                          : shogo

EXIF Metadata provided by EXIF.tools