Encore Electronic Enh908 Nwy Users Manual ®

ENH908-NWY to the manual eeeb9b78-88f5-4eb4-83ef-1893d055c0a6

: Encore-Electronic Encore-Electronic-Enh908-Nwy-Users-Manual-540274 encore-electronic-enh908-nwy-users-manual-540274 encore-electronic pdf

Open the PDF directly: View PDF .
Page Count: 6

ENH908-NWY

8 Port Switch

User Guide

0

The ENH908-NWY is a powerful, high-performance Fast

Ethernet switch, with all ports capable of 10 or 100Mbps

auto-negotiation operation (NWay), which means the switch

could automatically negotiate with the connected partners on

the network speed and duplex mode. It is ideal for

micro-segmenting large networks into smaller, connected

subnets for improved performance, enabling the bandwidth

demanding multimedia and imaging applications. Compared

to the shared 10Mbps or 100Mbps networks, the switch

delivers a dedicated 10/100Mbps connection to every

attached client with no bandwidth congestion issue. This

switch also supports auto MDI / MDI-X function. Each port

could be used to connect to another switch or hub with no

crossover RJ-45 cable.

Store-and-forward switching mode promises the low latency

plus eliminates all the network errors, including runt and CRC

error packets. To work under full-duplex mode, transmission

and reception of the frames can occur simultaneously without

causing collisions as well as double the network bandwidth.

The switch is plug-n-play without any software to configure

and also fully compliant with all kinds of network protocols.

Moreover, the rich diagnostic LEDs on the front-panel can

provide the operating status of individual port and whole

system.

Before you start to install the switch, check the following

contents in this package：

z One NWay switch

z One external power adapter

1

z User’s manual

Please refer to the following table for LED definition

8port

LED Status Operation

Steady Green Power is on Power

Off Power is off

Steady Green The port is connected

Blinking Green

The port is transmitting/receiving

data.

Link/Act

Off No connection

Rear Panel

8port

2

Connect each station to the switch by twisted-pair cable.

Plug one RJ-45 connector into a RJ-45 port of the switch,

and plug the other RJ-45 connector into the station’s network

adapter. Power on the switch and then system is ready.

For cable selection, refer to the following table.

In making a switch interconnection, you could use any port to

connect another switch with straight or crossover cable. As

all the ports support auto MDI / MDI-X function, using a

straight cable to make a switch-to-switch connection is

allowed.

For cable selection, refer to the following table：

3

Network Speed Cable Type Max. Length

10Mbps Cat. 3, 4, 5 UTP/STP 100 meters

100Mbps Cat. 5 UTP/STP 100 meters

Standard IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3x full duplex operation and flow

control

Interface 8* 10/100Mbps RJ-45 Fast Ethernet Ports

Uplink Auto MDI/MDI-X（Auto crossover）

Network Speed 10/100Mbps & Full/Half duplex mode auto

detection

MAC Address

Table 1K MAC address entries

Memory 768KBytes (8port)

Power Supply External Power adapter

5V DC 0.6A

EMI

CE, FCC

4

FCC Certifications

This Equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct

the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference

received; including interference that may cause undesired operation.

CE Mark Warning

This equipment complies with the requirements relating to

electromagnetic compatibility, EN 55022 class A for ITE, the essential

protection requirement of Council Directive 89/336/EEC on the

approximation of the laws of the Member States relating to

electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may

be possible that information in this document is not up-to-date. Please

check with your local distributors for the latest information. No part of

this document can be copied or reproduced in any form without written

consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective

companies.

Copyright © 2008, All Rights Reserved.

5