Enlighted SU4S Intelligent Light Sensor for Smart Networked Energy Saving Light Systems using 802.15.4 protocol stack and BLE for communications. User Manual PowerPoint Presentation

Enlighted, Inc. Intelligent Light Sensor for Smart Networked Energy Saving Light Systems using 802.15.4 protocol stack and BLE for communications. PowerPoint Presentation

Contents

Users Mnual

Page 5 Page 6 Page 1Copyright © 2016 Enlighted Inc. All rights reserved.All other brand or product names are trademarks oftheir respective companies or organizations.TechnicalSupportFor questions regardingthe installation or operation ofthis product, contact EnlightedTechnical Support: support@enlightedinc.comCompany Contact InformationLocation: 930 Benecia Ave, Sunnyvale, CA 94085Phone: +1.650.964.1094 Web: enlightedinc.comFCC and Industry Canada Compliance InformationThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions:•this device may not cause harmful interference, AND•this device must accept any interference received, includinginterference that may cause undesired operation.Changes or modifications not expressly approved by Enlighted Inc.could void the user's authority to operate the equipment.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationest autorisée aux deux conditions suivantes:•l'appareil ne doit pas produire de brouillage, ET•l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'encompromettre le fonctionnement.CEThis device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014).Enlighted Smart Sensor UnitSmart Sensor Unit(SU-4S)Installation InstructionsApplicable ForSU-4S-HSU-4S-LShipped ComponentsSmart SensorAnchor ScrewItems you will NeedEnlighted Sensor Cable: CBL-2-7FEnlighted Control Unit93-01658-01 Rev01Model: SU-4SFCC ID: AQQ-SU4S IC: 10138A-SU4S
Page 2 Page 3 Page 4InstallationFigure 5 CautionInstallation and maintenance must be performed by a qualifiedelectrician in accordance with local, state, and national electrical codes (NEC) and requirements.Figure 1 LED Status Description/SolutionLED not on Check power and wiringPurple solid All LEDs are on during boot time for 5-6 secondsGreen blinking Sensor commissioned and workingRed blinking Incompatibility between LED driver and sensor–Replace LED driver and if not resolved, replace sensor. Red solid Faulty sensor –replace sensorGreen solid Sensor installed, initialized, and uncommissioned –waiting for discovery.Blue solid Image being upgraded.LED DescriptionStep 1: Turn off all power to the light fixture by switching off the circuit breaker.Step 2: Mount the Control Unit (CU) in a UL approved enclosure. Refer to the Control Unit Installation Guide. See Figure 5 for the wiring connections from the CU. Step 3: Determine the location of the sensor in the fixture. Figure 1.The Smart Sensor (SU-4S) should be mounted to the ceiling within a few inches (between 13/4” to 3”) of the lighting fixture and over the service area of the light. Step 4: Select a place for the RJ12 data cable from the CU to exit and make a small cut in the ceiling tile for the cable to exit. Step 5: Install the Smart Sensor anchor screw (as shown). Figure 3.Step 6: Connect the RJ12 data cable to the Sensor (bottom entry). Figure 3.Step 7: Slide the Smart Sensor onto the screw head. Step 8: Slip the excess RJ12 data cable up into the plenum area and adjust the ceiling tile to the original position. Figure 4.Step 9: Switch on the circuit breaker to turn the power on.Figure 2 Figure 3 Figure 4 Anchor Screw RJ12 Cable1”Drill 5/8” hole

Navigation menu