Enlighted SU4S Intelligent Light Sensor for Smart Networked Energy Saving Light Systems using 802.15.4 protocol stack and BLE for communications. User Manual PowerPoint Presentation

Enlighted, Inc. Intelligent Light Sensor for Smart Networked Energy Saving Light Systems using 802.15.4 protocol stack and BLE for communications. PowerPoint Presentation

Contents

Users Mnual

Page 5 Page 6 Page 1
Copyright © 2016 Enlighted Inc. All rights reserved.
All other brand or product names are trademarks of
their respective companies or organizations.
TechnicalSupport
For questions regardingthe installation or operation of
this product, contact Enlighted
Technical Support: support@enlightedinc.com
Company Contact Information
Location: 930 Benecia Ave, Sunnyvale, CA 94085
Phone: +1.650.964.1094
Web: enlightedinc.com
FCC and Industry Canada Compliance Information
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
•this device may not cause harmful interference, AND
•this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by Enlighted Inc.
could void the user's authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
•l'appareil ne doit pas produire de brouillage, ET
•l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
CE
This device complies with the essential requirements and other
relevant requirements of the R&TTE Directive (1999/5/EC). The
equipment is Class 1 radio equipment which can be placed on the
market and be put into service without restrictions in accordance
with article 1(3) of Commission Decision 2000/299/EC (Version July
2014).
Enlighted Smart Sensor Unit
Smart Sensor Unit
(SU-4S)
Installation Instructions
Applicable For
SU-4S-H
SU-4S-L
Shipped Components
Smart Sensor
Anchor Screw
Items you will Need
Enlighted Sensor Cable: CBL-2-7F
Enlighted Control Unit
93-01658-01 Rev01
Model: SU-4S
FCC ID: AQQ-SU4S
IC: 10138A-SU4S
Page 2 Page 3 Page 4
Installation
Figure 5
Caution
Installation and maintenance must be performed by a qualified
electrician in accordance with local, state, and national electrical
codes (NEC) and requirements.
Figure 1
LED Status Description/Solution
LED not on Check power and wiring
Purple solid All LEDs are on during boot time for 5-6
seconds
Green blinking Sensor commissioned and working
Red blinking Incompatibility between LED driver and sensor
–Replace LED driver and if not resolved,
replace sensor.
Red solid Faulty sensor –replace sensor
Green solid Sensor installed, initialized, and
uncommissioned –waiting for discovery.
Blue solid Image being upgraded.
LED Description
Step 1: Turn off all power to the light fixture by switching off
the circuit breaker.
Step 2: Mount the Control Unit (CU) in a UL approved
enclosure. Refer to the Control Unit Installation Guide. See
Figure 5 for the wiring connections from the CU.
Step 3: Determine the
location of the sensor in
the fixture. Figure 1.
The Smart Sensor (SU-4S)
should be mounted to
the ceiling within a few
inches (between 13/4” to
3”) of the lighting fixture
and over the service
area of the light.
Step 4: Select a place for
the RJ12 data cable
from the CU to exit and
make a small cut in the
ceiling tile for the cable
to exit.
Step 5: Install the Smart Sensor
anchor screw (as shown).
Figure 3.
Step 6: Connect the RJ12
data cable to the Sensor
(bottom entry). Figure 3.
Step 7: Slide the Smart Sensor onto the screw head.
Step 8: Slip the excess RJ12 data cable up into the plenum
area and adjust the ceiling tile to the original position.
Figure 4.
Step 9: Switch on the circuit breaker to turn the power on.
Figure 2
Figure 3
Figure 4
Anchor Screw
RJ12 Cable
1”
Drill 5/8”
hole

Navigation menu