Enlighted SU5S SU5S User Manual PowerPoint Presentation
Enlighted, Inc. SU5S PowerPoint Presentation
User Manual
FCC and Industry Canada Compliance Information CE This device complies with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The equipment is Class 1 radio equipment which can be placed on the market and be put into service without restrictions in accordance with article 1(3) of Commission Decision 2000/299/EC (Version July 2014). Models: SU-5S-H: High Bay, Smart Sensor SU-5S-L: Standard Bay, Smart Sensor FCC ID: AQQ-SU5S IC: 10138A-SU5S in ar For questions regarding the installation or operation of this product, contact Enlighted Technical Support: support@enlightedinc.com Company Contact Information Location: 930 Benecia Ave, Sunnyvale, CA 94085 Phone: +1.650.964.1094 Web: enlightedinc.com im Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: • l'appareil ne doit pas produire de brouillage, ET • l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Smart Sensor (SU-5S) Installation Instructions Technical Support Smart Sensor (Front and Rear) el This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: • this device may not cause harmful interference, AND • this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Enlighted Inc. could void the user's authority to operate the equipment. Copyright © 2017 Enlighted Inc. All rights reserved. All other brand or product names are trademarks of their respective companies or organizations. Shipped Components Pr This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • Smart Sensor • Anchor Screw Supplemental Components • Enlighted Sensor Cable: CBL-2-7F • Enlighted Control Unit Page 5 Page 6 93-02058-01 Rev01 Page 1 Caution Installation and maintenance must be performed by a qualified electrician in accordance with local, state, and national electrical codes (NEC) and requirements. LED Description Step 4: Connect the RJ12 connector to the sensor bottom. Installation Anchor Screw Step 1: De-energize the luminaire. Sensor Cable in ar The Smart Sensor (SU-5S) should be mounted to the ceiling tile within a few inches (between 13/4” to 3”) of the lighting fixture. Step 2: Determine the location of the sensor. Push and rotate the anchor screw to the tile at that location. Description/Solution LED not on Check power and wiring Green blinking Sensor commissioned and working Red blinking Sensor not commissioned Red solid Faulty sensor – replace sensor Green solid Sensor installed, initialized, and uncommissioned – waiting for discovery. Blue solid Sensor received a request to identify itself For wiring connections from the Control Unit to the sensor, refer to the Control Unit Installation Guide. Wiring Diagram: Step 3: Select a place near the anchor screw for the RJ12 connector of the sensor cable from the Control Unit (CU) to exit. See Wiring Diagram on Page 4. Make a small cut in the ceiling tile for the cable to exit. Pr el im Step 5: Slide the Smart Sensor onto the screw head. LED Status Step 6: Slip the excess sensor cable up into the plenum area and adjust the ceiling tile to the original position. Step 7: Energize the luminaire and confirm that the green LED is solid. Page 2 Page 3 Page 4
Source Exif Data:
EXIF Metadata provided by EXIF.tools