Enping Ding Li Acoustics Technological UB-102B wireless microphone (TX) User Manual

Enping Ding Li Acoustics Technological Co., Ltd. wireless microphone (TX) Users Manual

User Manual

Download: Enping Ding Li Acoustics Technological UB-102B wireless microphone (TX) User Manual
Mirror Download [FCC.gov]Enping Ding Li Acoustics Technological UB-102B wireless microphone (TX) User Manual
Document ID1224645
Application ID0KL+LqW5OUeyCo9y/vNjYA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize449.05kB (5613097 bits)
Date Submitted2010-01-08 00:00:00
Date Available2010-01-08 00:00:00
Creation Date2009-11-23 10:01:17
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2009-12-24 22:05:44
Document TitleUsers Manual
Document CreatorPScript5.dll Version 5.2
Document Author: vip

lZOOChanneIs Pll Wireless Serm
USER G II I BE
UB-1OZB
F p Wireless
“ H - L L Microphone
Thank you and welcome to the world ofwireless. This brand new system is designed to
provide you with the most audio clarity and strongest anti-interference protection that you
can ever imagine.
Follow our instructions in this user guide, and enjoy the easy way of setting up the system
and operating the system now.
FREQUENCY BAND SELECTION
Most countries closely regulate the radio frequencies used in the transmission ofwireless
information.
These regulations state which devices can use which frequencies, and help to limit the
amount of RF (radio frequency) interference in all wireless communications.
To be flexible enough to operate worldwide, this new system receiver is available in a
numberoffrequency ranges. Each frequency range, or band, spans up in 30 MHz of the
wireless broadcast spectrum. Available bands are:
U0: 514 - 698 MHI
To facilitate system setup and protect against RF interference, each system comes with
multiple predefined frequency groups and channels.
When using a single system, the operating frequency will generally not have to he changed.
In an installation with multiple receiver/transmitter systems, each system must operate on a
separate channel. The group and channel system provides an optimum frequency spread
when using multiple systems.
Within a single frequency hand, up to 13 individual transmitter/receiver systems may be
used in a single installation. In regions where additional frequency bands are available, it is
possible to operate up to 20 systems simultaneously. Check with your local retailerfer
information on which bands are available in your area.
1200 Channels
Pl.l. Wireless
TABLE OF CONTENTS
System Components.
Receiver Features
Handheld Transmitter .......
Bodypack Transmitter
Single System Setup
Multiple System Setup .....
Programming
Receiver Programming
Transmitter Programming
The Master Frequency List ......
Rack-Mounting Receivers
Tips for Improving System Performance .......
Troubleshooting.
Specifications.
'2°° °"“““e's _
PLL Wireless
System Components Any system will include:
- Receiver
' Powersupply
4 4 ' Userguide
Optional accessories:
- Rack mount supplies
‘ Short rack ear
' Long rack ear
Link barto mount to similar receiver
' 8 rack ear screws
' 4 rack mount screws With washers
% - Extension cables and connectors forlront—mounting antennas
And, a Handheld system will include:
- Microphone head CD (Optional DM-58i EM-MS)
' Handheld transmitter @
' Microphone holder ®
' 2AAbatteries
CD (2
Or, a Body pack systems will include:
- Bodypacktransmitter @
- Lavaiier microphone (Optional LV70211®,LV76210@‘ LV—MH @)
- Headworn microphone (Optional H574111C5)H376210@iHSflleSQN
' 2AAAbatteries
(“EDD
Or, a Guitarsystem will include:
' Body pack transmitter (1)
' 1/4 jack lo miniA-pin guitarcable C2)
. 2AAAbatteries
Receiver Features
Front Panel
3 Z O
o a so
vs st. @ ......
(D (2 0 ® ® (6) ® @
6) RF LED - Indicates strength ofinconilng RFslgnaI.
(2 Audio LED - lndicates strength of incoming audio signal.
(37 LCD display - See “Programming" on page 6.
GB Menu switch - Press to scroll through menu options. See“Programming "on page 6
C5) Set switch - Press to select the currently displayed menu option See “Programming ” on page 6
63) Volume control The volume control dial should generally be left in the clockwise position.
Turning the dial counter-clockwise decreases receiver output level.
® Infrared (IR) port - Broadcasts IR signal to transmitterto synchronize frequencies.
® Smart option - Press to initiate IR connection between receiver and transmitter. See
“ Programming”on page 5
(9) Power On/Off switch - Push up to turn on, push down to turn off.
Back Panel
A l;
gr ® ® ;
sfi W ”7
fl @
G) 69 ® @ (Z)
(D Antenna jackB
O) 1/4 lack outpuijack
(3) XLR outputjack
@ Squelch
6) Adaptercord tie-oif- Follow stips shown to secure cord to receiver body.
C5) AC adapterjack
®
Antenna jackA
1200 channels
PLI. Wireless
Handheld Transmitter
6)
®
@ S,
iaiaE
@ LED
(5)
Features
67 Interchangeable microphone head
(2) IR port - Receives infrared beam to synchronize frequencies. When using multiple systems.
only one transmitter IR port should be exposed at a time.
© LCD screen — See“ Transmitter Programming " on page 6.
® On-ofl/ mute switch - Press and hold to turn on orofl. Press and release to mute or unmute
To avoid accidentally muting the microphone during a performance, lock the front panel
while the microphone is in use.
(5) Mute indicator— Red mute on
(a) Set sWitch - See“Transmitter Programming”on page 6
Changing Batteries
Expected life loran Alkaline battery is approximately 5 hours.
When the battery bar in LCD display is empty, the batteries should be changed immediately as
shown below:
1200 Channels
pu. Wireless _
Bodypack Transmitter Fawn“
Q) Antenna
@ LCD screen
® On-off/ mute switch
(3 Press and hold to turn on or off Press and release to mute or uhmute.
@ Set Witch
6) Battery cover
@ IR port
@ Receives infrared beam to synchronize frequencies When using multiple systems, only
(3) one transmitter IR port should be exposed at a time.
\ (7) Gain adjustmentswitch
(41
® ® Mute indicator
‘J Red: mute on
(97 4-Pin mlcrophonelnputjack
© \.
if E
l ”wag
Wearing the Bedypaek Transmitter
Clip the transmitterto a belt until the belt is pressed against the base ofthe clip as show on
the left.
2 Changing Batteries
Expected llfe foran Alkaline battery is approximately 8 hours
When the battery bar in LCD display lS empty, the batteries should be changed immediately
as shown below:
1200 channels
pu names; _
Single System Setup
Note: transmitting devices such as cellular phones and two-way radios may interfere with
wireless audio transmissions. Keep your transmitters and receivers away from these and
other potential sources of interference.
Follow these steps when using a single system:
1. Automatic Frequency Selection (D menu (27
Scans foran available channel and sets the receiverto that channel.
2. Automatic Transmitter Setup 5.0.
Exposed the IR portto the receiver. press S 0.
Multiple System Setup Follow these steps when using multiple systems in a single installation
1. Turn all receivers on and all transmitters off
2. Setall receivers to the same frequency group.
3. Perform Automatic Frequency Selection from the Single System Setup section above
4. Turn on the firsttransmitter.
5. Perform Automatic Transmitter Setup from the Single System Setup section above.
Repeat for each system.
Be sure that only one transmitter‘s IR port is exposed when synchronizing a system.
pu w‘reless _
Programming Anyoption displayed on screen will generally time out afterfive seconds.
Receiver Programming
GroupSelectian 6] 2X men” (DEE @ E
Allows manual selection ofa frequency group. Pressing set increases the group number
8 E by one. When the correct frequency is displayed press 5.0.. For best results when
mg, operating multiple systems, set all systems to a single group; then set each system to a
unique channelwithinthatgroup.
n Manual Channel Selection ® 3x "i ® ' 531 ©
U Allows manual selection ofa frequency channel. Pressing set increases the channel
m number by one. When the correct frequency is displayed press S.0..
E G U U 0 Display Frequency (1) 4X men” @ se‘ ,
' mm Display the current frequency in MHz. Press again to display group and channel
Lock or Unlock Receiver Settings 55“ A + [M]
Hold down the set key and press menu to lock or unlock the receiver. When locked, the
current receiver settings cannot be changed.
Tm‘f Antenna Status
“ ' Indicates RF actiVity Onlyone antenna is active atany one time.
Transmitter Battery Status
Indicates a low transmitter battery charge.
Transmitter Programming
ManuaIIySeIecta Group and/or Channel Sat
1 Press and hold the set button until the GROUP and CHANNEL displays begin to
m" alternate.
2 To change the group setting. release the set button while GROUP is displayed. While
f—\ GROUP is flashing. pressing set increases the group setting by one.
g” 3 Press power button to sWitch between GROUP and CHANNEL settings
66!
65
Remember In press power and set button to confirm when the seltlng is completed.
a Lock or Unlock Transmitter Settings P°W9f + 53‘ 4
Press the power and set buttons simultaneously to lock or unlock the transmitter settings.
When locked. the current settings cannot be changed manually
Battery Status
Indicates charge remaining in transmitter batteries.
MasterList Indicator
Indicates that a master list frequency is currently in use Group or channel information will
be display.
pu w reless _
Press set till GROUP and CHANNEL display begins to alternate. Hold set and press power
till MASTER displays.
mm INCUMPATIBLE Frequency Warning
The INCOMPATlBLE warning indicates that the receiverand transmitterare set
to incompatible frequency bands. Contact your retailerforassistance.
The Master Frequency List
Receiver
UsingtheMaster + tPOWe’
The“Master”offrequencies should be accessed only by experienced users in situations
Which call for precise frequency selection, The“Master”is a comprehensive index ofall
availablefrequenciesin 25 kHz increments
To access the Master, hold down the menu button while powering on the receiver.
Under the display oflrequency
Select Frequencies in the Master (1) 3x menu (2) set @ I
While FREQUENCY is flashing, the setbuttori scrolls up through all available frequencies;
803 GS MHZ The menu button scrolls down.Press andrelease to changethe frequencyin 25 kHz
increments; press and hold to scroll quickly.
lfyou know thefrequency you need, to speed upyourselection, you can followZ steps below:
8 g G. L} 35 um i.Selectthe frequencyunderzero, like 0 425MHz.
2. PressS.O., it Will sWitch to select the frequencyabove zero, like 801MHZ.Press and
release to changethe frequency in 1 MHz increments, pressand hold to scroll quickly.
8 G i, Li 135 "W When the correct frequency is displayed, waitfive seconds forthe screen to timeout
Under the display ofgroup and channel
set
SelectFrequencies in the Master 0) 3x menu‘ ® set (3) menu I
ElMEi While CHANNEL is flashing, the set bulton scrolls upthrough all
available frequencies; the menu button scrolls down . Press and release to change the
frequency in 25 kHz increments; press and hold to scroll quickly.
Ifyou know the group and channel you need, to speed up yourselection, you can follow
“r” W 25te below:
a a f’
1 Selectthe channel.
2 Press S.0., ltWiII sWitch to selectthe group Press and release to change the frequency
in 1 MHz increments; press and hold to scroll quickly
When the correctgroup and channel is displayed, wait five secondsforthe screen to time
out.
Exitthe Master CD 2x new ® set
To exitthe Masterand return to normal system operations, press menu, then set
Transmitter
$235 Enterthe Master Press andhold Eel + power
i I =
While the“ Master” is shown, release set * poweri then press power + set to enter the
“Master.”
Select Frequencies in the Master
Press and hold the set button till the group is flashing. Press and release to change the
frequency in 1 MHz increments Press and hold to scroll quickly.
SWitch to channel select by pressing the power button
Press and hold the set button till the channel is flashing Press and release to change the
frequency in 25 Khz increments. Press and hold to scroll quickly.
.._M-“ Exit the Master Press andhuld 561 +
While the“ Master" is disappear, release set+ poweri then press power * set to exit the
"Master”
1200 channels
pu wireless _
Rack-Mounting Receivers
The suppfied mountmg hardware allows an recewer to be mounted in any standard 19"
audm equipment rack.
Hardware (‘ncluded) Assembly
QQQQ‘EQQQ
Tools (Not mcluded)
Tips for Improving SystEm 0 Maintain a line of sight between transmitter and antenna.
Performance 0 Avoid placing the receiver near metal surfaces or any digital equipment
(CD players. computers. etc.)
a Secure the AC adapter cable to the receiver using the cable retainer loop
a If rack-mounting the receiver, front-mount the antennas by using the
extension cables and connectors.
Troubleshooting
Issue Indicator status Solution
No sound or farm
sound
Transmitter power light all
Turn transmitter on
Make sure the +1, indicators on battery match the transmitter terminals
Insert a fresh battery
Receiver LCD of!
Make sure AC adapter is securely plugged into electrical outlet and into
Dc inputconnector on rear panel or receiver
Make sure AC electrical outlet works and is supplying proper vultage
Receiver display indicates antenna ' Press mute svvitcti en transmitter
activity ' Turn up receivervoiume control
' increase transmittergain switcn setting
~ Check cable connection between receiver and ampiirier or mixer
Receiver display indicates no ' Extend receiverantennas vertically
antenna actiwly. transmitter and - Move receiver away from metal objects
remit/er newer lights glflwmg - Check far line of signt between transmitter and receiver
- Move transmitter closer to receiver
~ Check that receiver and transmitter are using the same rrequency
Transmitter power light gicwmg or - Replace transmitter batteries
riasning red
INCOMPATIELE warning on - The INCOMPATIBLE warning indicates that the receiverand transmitterare
transmmer set to incompatible lreouency bands. contact your retailer for assistance.
Distortion or Receiver uispiay indicates antenna - Remcve nearby sources of RF interrerence (CD players. computers.
unwanted mi“ activity digital eflects. in—ear monitorsystems. etc)
b - cnange receiver and transmittertc a dinerent lrequency
ursts
' Reduce transmittergain
Replace transmitter battery
it using multiple systems. increase the rrequency spread between
systems
Distortion level
increases gradually
Transmitter power light glcwmg or
rlasning red
Replace transmitter batteries
Sound level dilrerent
lronr cabled guitar or
microphone. or when
using dinerent guitars
Adyust transmitter gain and receiver volume as necessary
FULL warning
displays on receiver
The FULL warning indicates tnat all available cnannels in the currently
selected gmup are in use When this occurs. reprogram all systems to an
alternate group.
Cannot turn
transmitter o"
Transmitter lightriashtng red
Replace transmitter batteries
10
Specifications
System
Operating Range lnder Typical Crmditirins
100m (30011)
Nole actual range depends on RF signal absorption
reflection, and interference
l\nd"tr Frque y Response (dc 7am
Minimum: 50 Hz
Maximum 20 kHz
(Overall eystern frequency depends on
microphone elerneni.)
Total llamomc uisiuriion (rel. i/— so ltllu deviation,
400112 tone)
0.5%,iypioal
Dynamic Range
>loo dB A-weighled
operating Tenperniure Range
718°C (0°FJ to +57°c (+135"F)
Nole pattery characteristics may iirnittnis range
UBV 102 Rodi/pack Transml LLC!’
Gain tdjusimuni, Rangn
SOdE
l'iDul lchdeincc
5OOKQ
Rl' Trunsmllzer OuLDuL
so mW maximum (dependent on applicable country
regulations)
Dimvnsinns
85 mmH x70 mmW x 20mmD
11
Weight
97 9 Without batteries
llnusmll
Molded ABS case
l’ancr quurcmcnts
2‘MA"lee alkaline or rechargeable batteries
Hatlcrv Lilr'
>5 nours (alkaline)
UHrlOZ Handheld Transmitter
le Trarsiniiior OulDul
30 rnw maximum (dependent on applicable
country regulations)
Dimensions (including Evl—lls cartridge)
270 mm x 52 mm dla.
ll'f'lghl
250 g wllhcut bailerles
llnuslng
Mclded ABS handle and battery cup
l’nvm' Raqlulrnmnnls
2 “AA" size alkaline ur rechargeable batlerles
Bullc’y l_i i‘e
>s hours (alkaline)
UHFleZ Receiver
Dimensions
205mmH x 150mmW x 39 mmD
Wei ghl
960 9
Housing
Galvanized steel
Auuiu Outpui Leuo (rel. w— SOkllz duvl‘d‘c all
with 400112 irrno)
xLR connector (into 600 9 load): —300BV
1/4 Inch connector (into 3000 51 load) —9dBv
nutpui lmpednnce
XLR connector 200 0
1/4 inch cpnneclor 1m
XLR output
lmpedance balanced
Fin 1 Ground (cable shield)
Pin 2 Audlc
Pin 3 No Audio
Senslllvli)‘
405 dBm for 12 dB SlNAD. typical
lmaflc Rejection
>7o dB, typical
Pam)!“ RCuLlTolnans
22V do at 40mm, supplied oy external
power supply

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 15
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:e2c549bf-1067-46d3-882f-b005617faf2a
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2009:11:23 10:01:17+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2009:12:24 22:05:44+08:00
Metadata Date                   : 2009:12:24 22:05:44+08:00
Document ID                     : uuid:e6e01c7f-5334-4928-b893-15e8de55c094
Format                          : application/pdf
Title                           : <5548462D313032CBB5C3F7CAE92830392E36D0DEB8C432292E636472>
Creator                         : vip
Author                          : vip
EXIF Metadata provided by EXIF.tools
FCC ID Filing: RW5UB-102B

Navigation menu