Enterprise Electronics LRL0005 KEYLESS ENTRY PAD User Manual USERS MANUAL 1
Enterprise Electronics, L.L.C. KEYLESS ENTRY PAD USERS MANUAL 1
Contents
- 1. USERS MANUAL 1
- 2. USERS MANUAL 2
USERS MANUAL 1
Jbs echnulugles Your Wireless Keypad will also work with a remote transmitter. For purchase of a remote transmitter or additional accessories, visit www.directwholesale.net or call 800—659—0764. “A / FOR TECHNICAL ASSISTANCE www.bu||dogsecurity.com ema' : techsupport@jbstech.com 1-800-878-8007 FOR TECHNICAL ASSISTANCE www. bulldogsecu rity. com 800—878—8007 JBS Technologies 225 Technology Way Steubenville, OH 43952 YOUR WARRANTY Here's how your warranty works: JBS Technologies warrants to the original customer, and the original car a limited lifetime warranty. Within 12 months of purchase, JBS Technologies will repair or replace, our option, any defective system at no charge. After 12 months from date of purchase, JBS Technologies will, at our option, repair or replace the system for a $30 shipping and handling fee. Installation, labor, removal and reinstallation are not the responsibility of JBS Technologies. Registration must be completed and sent in within fourteen (14) days of purchase in order to validate the warranty. JBS Technologies makes no warranty against the theft of a vehicle or its contents. This warranty is not to be construed as an insurance policy against loss. DISCLAIMER JBS Technologies disclaims the warranty of merchantability and fitness for any particular use. This disclaimer shall be effective as to all claims ofany kind made by or through any wholesaler, retailer, consumer or any other person or entity. Some states do not permit the disclaimer of implied warranties in some sales. Hence, this disclaimer may not apply to you. LIMITATION OF REMEDIES Consumer's remedy is limited to repair or replacement of the unit, and in no event shall exceed the purchase price. Incidental, consequential an/or indirect damages are expressly disclaimed. No person or entity is authorized to alter, amend or increase this limited warranty. NOTES 18 CONTENTS System Features.. . . ..4 System Components 4 Tecnmom Ass1slance. . ..4 Ee1ore You Eegm 5 Precautions. ..5 Making W1ring Connections 677 Localmg & Makmg Connecl1ons.. . Localmg & Determmmg Your Door Lock Types... . .. 10 Tesnng Door Locks ... .. 10 ConnectmgDoorLocks........... ...11712 14-P1n Harness Diagram .. .. .. 12 Door Lock Type by Manufacturer. .. . .. .. 13 ongvammmg Vour KeypacL ..14-15 Recewer Programmmg Instructions ...... 1545 Using Your W1re|ess Keypad .. 1s Mounting Your W1re|ess Keypad.. .. . .. .. 17 FCCID No11ee.... .. 17 Notes . .. .. 19 Protected by one or more of me vo|1owmg palems: Patent 3631 1458 Fa1ent V6.617975 Pending PatemAppficanon 09/557 582 WIRELESS KEYPAD TP100 SYSTEM FEATURES Five-Button Remnteiy lock and unlock your vehicle lrorn the outside Vlnreless Keypad Shner You can't steal whal you can't start. lmmobiliaer Most insurance companies otter a discount lor this leatuie lOpnonal Pan tm Required) Trunk Release Remnleiy opens your iiunk lootional part W5 requlled] Parking Light Contirms that youivehiole has received a remote Confirmation signal and remains on tor ten seconds when disarming lootional part tt775 lequlred.) Limited Lifetime Guarantees ltelorig protection Warranty SYSTEM COMPONENTS Your system includes: t-lnstallation & Operation Guide tattPin wire Harness 1aMaln Control Module t-Warranty t-Five-Buttori wireless Keypad _TECHNICAL ASSISTANCE Since there are many ditlerent makes and models at vehicles, tor wiring charts and diagrams. lirst check our website at www.bulldogsecurity.com, call our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at eon-3794007, or Email us at techsupport@jbstech.com. You must give the tollowing information: - Name ~ Telephone Number with Area Code (Fax number it applicable) ~ Year, Make, and Model or the vehicle - The model number or the system you are installing - The type ot assistance you are requestlng MOUNTING YOUR WIRELESS KEYPAD_ Belore you mount the wireless touchpad to the outside or the vehicie, make sure the control module is tirst installed Atter your control module has been Wired to the vehicle's door lock system. you will need to program the wireless touchpad to the control module Follow the instructions lor operating the keypad to ensure all tunctions are working properly After you have tested all the functlons, you can mount the keypad to the desired location. Be sure to apply the keypad to a clean and dry surtace betore mounting. it is suggested that you use an alcohol pad or wax remover tor the desired location Room temperature mounting suriace is recommended but not necessary To mount the keypad: tirst roll the drivers window down as to prevent accidental lock-outs Remove the protective backing on the double sided tape Apply the keypad to the desired clean surtace. Press tirmly and hold tor to seconds. l=or painting the exterior cover you should remove the outside casing tirst betore applying to the vehicle. INSTALLATION NOTE: ll your vehicle is serviced or the vehicle's battery is disconnected, the keypad system may stop lunctioning. it this happens, your keypad wrll need to be reprogrammed to the [TP] module Either disconnect the battery lor 30 seconds and reconnect. or unplug the 14 pin harness lrorn the HP] module lor 30 seconds and plug back in In both cases, enter your 5-digit primahy code to reprogram the KEYPAD to your [TP] module. Ii you purchased optional part #773 starter immobilizer, show this card to your insurance agent, you may be ellgible for a discount on your automobile insurance. This JBS system is equipped Wlth Starter Immobillzation Output. Transmitter FCC ID: QV4-LHL0005 Transmitter IC ID: 4545A-LRL0005 This device complies wrrh Part ts ol the FCC rules and Rssszto ot lndustry Canada Operation is sublect to the tolloWing two conditions (i) This device may not cause harmlul interterence, and (2) This device must accept any interterence received, including interterence that may cause undesired operation changes or modilicaiions not expressly approved by the party responsible tor compliance could void the user's authority to operate the equipment 17 RECEIVER PROGRAMMING INSTRUCTIONS ConI._ Adding add onal remotes with a working keypad Enter the 5-Digit Primary Code Press and hold Buttons 7/8 and 9/0 at the same time on the keypad for 20 seconds. release. Next. press and hold Button wt (Lock) on the new remote tor 20 seconds. then release Button wt (Lock). try new remote Adding additional remotes without a working keypad Unplug the main unit lrorn under the dash. wait one minute Plug the unit back in and use the new remote control. _USING YOUR WIRELESS KEYPAD _ I,12II 342II 55 7s 90 To Lock: Press Buttons 7/8 and 9/0 at the same tlme. anyllrne. Without Enterlrtg a Primary or Secondary Code To unlock: Enter your 5-Digit Primary or Secondary Code. The 9/0 Button Will llash (2) Two times and the Vehicle will automatically UNLOCK alter the last Digit oi the 5-Digit code is entered To Pop Trunk: Enter your 57Digit Primary or Secondary Code and press the 5/6 Button. The 9/0 Button Will llash (2) Two times and it the Trunk Release is connect the Trunk will Pop. Receiver Programming Mode: Enter your Sleglt Primary or Secondary Code and press the 7/3 Button PROGRAMMING FUNCTIONS FOR YOUR WALLET ATTENTION: We urge you to immediately place this Card in your wallet. "i.;;ii;;.;i;i.;,i'min'.ii;i. """""""""""""""""""" ' Enierpresetsoigit primary code Then hold down Button Tlelortuseconds You are now in programming mode Alter programming to exit programming mode. press and release button 7/5 again Programmhg 3.5 or 0.7 second door lodr/unlodr length Press buttons 7/5 and 9/0 at the same time once the unit is programmed tor a 5 second door look/unlock Press buttons m3 and m at the same time MlCE the unit is programmed lcr D 7 seoond door look/unlock Programm'rlg lcr dual putso lodr/unlodr Press button 3/4 once the unit is programmed lor dual pulse unlook Press button 3/4 Mice the unit is programmed tor dual pulse lock Press button 314 three times the unit is programmed lor no dual pulse lock/unlock BEFORE YOU BEGIN Congratulations. you have purchased one oi the most advanced keyless entry systems ever made. Your new keyless entry is a technological breakthrough utilizing the most advanced. state ol the art technology and components lt is computer controlled and manulactured in the u.s A. The dependability and variety cl leatures make Bulldog Security the leader in the industry. Enloy your new keyless entry tor years to comel Read this manual thoroughly before starting the installation. You must also decide it any options are desired such as starter immobilizer. trunk release and parking light contirmation. An optional relay may be needed for some ol these options Please do not skip any steps. Since there are many dlflerent makes and modeIS OT vehlcies. Tor wtrlrig charts and diagrams. Visit our website. www.jbstecn.com PRECAUTIONS This system is designed for vehicles with power door locks only. This system Will add remote keyless entry leatures to any vehicle With power door locks. This Will also work as a replacement system for the tactory installed keyless entry system Do NOT use mechanical wiring connections. such as crimp or snap together taps. Follow instructions on pages 6-7. no NOT disconnectthe battery it the vehicle has an antlsthefiscoded radio or is equlpped With an airbag. Doing so may cause a warning light to be displayed and may require a trip to the dealer to be corrected. Do NOT leave the interior or exterior lights on lor an extended period oi time as it may cause battery drain. DO NOT mount the oontloI moduIe untiI aII connections have been made and tested Using wlre (les or double sided tape, MOUNT THE MODULE UNDER THE DASH. MAKING WIRING CONNECTIONS 1. Strip back two inches at insulation on the wire trom the “we“ emf"- Two inches ot Bare Wire Imam 2. Strip back one inch of insulation on the wire you need to connect to. One Inch 01 Bare Wire l—‘—l I3: 3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through. so: 4. Insert the wire trom the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. ‘ 5. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them togetheruse this method for all connections. Sr: , Wire Tm Electrical Tape CAUTION: All wires must be wrapped and taped. PROGRAMMING YOUR KEYPAD Cont: To Test: Enter the New Secondary SrDlgiI Code, 9/0 Will flash (1) One time and the Doors should UNLOCK. Secondary Code Erasure: For your convenience, you can also Erase the 5-Dlglt Secondary Code to the KEYPAD To do this, enterthe 5rDlgiI Primary Code, then Press and Hold Button 1/2, then Press and Hold Button 7/9, the 9/0 Button Wlll llash it) One tlme Release the we and 7/5 Buttons, the KEYPAD Will send a UNLOCK command to the TP Module and the 9/0 Button will llash (1) One time again to indicate the Programming is complete To Test: Enter the Old Secondary 5-Dlgit Code, 9/0 will not Ilastl and the Door Locks should not Respond. RECEIVER PROGRAMMING INSTRUCTIONS_ To Enter Receiver Program 9 Mod . Enter the SrDiglt Primary Code. Press Button 7/8 for to seconds then release You are now in programmlng mode. After programming, to exit programming mode press and release Button 7/B again. Programming 0.7 and 3.5 second door lock/unlock pulse time Press buttons 7/3 and 9/0 at the same tlme once the urllt ls programmed Ior 3.5 second door lock/unlock Press buttons 7/8 and 9/0 at the same tlrne twlCE; the urllt I5 programmed tor 0 7 second door lock/unlock. Programming lor dual pulse lock/unlock (Used on some imports) Press Button 3/4 once, the unit is programmed tor dual pulse unlock. Press Button 3/4 mice, the unit is programmed loi dual pulse lock. Press Button 3/4 to) Three times. the unit is programmed lor no Dual Pulse Lock/Unlock. (Continued on Pg. 16) OPERATING FUNCTIONS FOR YOUR WALLET med ely placeth card in yourwallet. To Look: Press the 7/8 and 9/0 Buttons at the same time it the Starter immobilizer Belay is installed at this time, the starter immobilizer will engage To Unlock: Enter the 5rDiglt Primaiy Code, when the last number 1 or your Primary code is entered the doors Will Unlock and the 1 Starter interrupt will be disengaged l Trunk Pop (it connected) Enter the 5-Digit Primary Code Pressi and release button 5/6 (trunk). the trunk will release. This Will i send a negative 250ma output as long as button 5/6 is held down. 1 lr you need a momentary pulse out of the 5/6 Button, lust press 1 and release. 1 lo
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 5 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:f8c34b91-c129-4103-9f7f-9e6298ce6e80 Modify Date : 2006:11:13 16:44:03-05:00 Create Date : 2006:11:13 16:41:51-05:00 Metadata Date : 2006:11:13 16:44:03-05:00 Document ID : uuid:2b6e2485-cc8d-4b70-a58b-ba4fff08f3f8 Format : application/pdfEXIF Metadata provided by EXIF.tools