Entone Technologies 50-0100-CL-01 5GHz WiFi User Manual CL 120 manual 1112 2014

Entone Technologies (HK) Limited 5GHz WiFi CL 120 manual 1112 2014

Users Manual

Product Specification CL-120 IEEE802.11 a/n 3T3R PCIe Module Version: 1.0 Date: OCT,15,2014
Release History DATE REV Description of Change 2014/10/15 1.0 Initial release
CL-120 IEEE802.11a/n 3T3R PCIe Module 1. Introduction CL-120 is an integrated the Celeno CLR260 single-chip 5GHz IEEE802.11a/n 3T3R MAC/Baseband/Radio with pcie interface. CL-120 fully complies with IEEE802.11n and IEEE802.11a/n feature rich wireless connectivity at high standards, delivers reliable, cost-effective, throughput from an extended distance. 2. Features Interoperable with IEEE802.11a/n WLAN. Reverse direction grant data flow and frame aggregation. Support 20MHz and 40MHZ Bandwidth PHY Rate max 450Mbps operations. Wireless multimedia enhancements quality of service support (QoS). Legacy and high throughput modes. Multiple BSSID support. WEP 64/128, WPA, WPA2, TKIP, and AES software encryption. PCIe Interface compliant. Low power with advanced power management. Operating systems – Windows XP 32/64,Vista 32/64, Linux, Macintosh. 3. General Specifications Product Specification Model Name CL-120 WLAN Standard IEEE 802.11a/n, 3T3RHost interface PCIe compatible Major Chipset Celeno CLR260 Dimensions Minimum Typical Maximum UnitLength 51 mmWidth 31 mmAntenna Connector 3 Path ipex connector Operating Condition Minimum Typical Maximum Unit Voltage DC 3.3 3.3 5 VTemperature -10 70 °CStorage temperature -20 70 °CHumidity Non-Operating 580 %
Electrical Specification Frequency Range 5180 - 5825Modulation BPSK, QPSK, 16QAM, 64QAM, DBPSK, DQPSK, and CCK Data Rate 802.11b CCK Mode xx Mbps 802.11a OFDM Mode 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n HT20 Mode GI 800ns 6.5 ~195 Mbps MCS 0 ~ MCS 23 802.11n HT20 Mode GI 400ns 7.2 ~216 Mbps MCS 0 ~ MCS 23 802.11n HT40 Mode GI 800ns 13.5 ~ 405Mbps MCS 0 ~ MCS 23 802.11n HT40 Mode GI 400ns 15 ~ 450Mbps MCS 0 ~ MCS 23 Output Tx power 5 GHz LOW Band 16.5dbm +/-1.5dbm 5 GHz Hi Band 17dbm +/-1.5dbm Rx Sensitivity 5 GHz a/n mcs7 < -68dbm Security WEP 64/128, WPA, WPA2, TKIP, and AES software encryption Operating System Compatibility Windows XP 32/64 Windows Vista 32/64 Windows 7 32/64 Linux Ubuntu 4. Mechanical Dimensions
5. CL-120 PCIe module installation(1)Checkmainboardqualityandmakesuretheconnectorifsolderedright.(2)GettheCL‐120,andplugintotheconnector.(3)Screwtofixthemodule(4)Assembletheantenna(5)ConnecttoaWirelessNetworkviaaWirelessNetworkRouterorAccessPoint
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification , Doc) of the host device to be addressed by the integrator/manufacturer. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. The FCC part 15.19 statement below has to also be available in the manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: S4A50-0100-CL-01".

Navigation menu