Entone Technologies 50-0100-CL-01 5GHz WiFi User Manual CL 120 manual 1112 2014

Download:
Mirror Download [FCC.gov]
Document ID	2461476
Application ID	XrH2jk/PbOaZq3OKhsDb1g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.56kB (181943 bits)
Date Submitted	2014-12-03 00:00:00
Date Available	2015-05-03 00:00:00
Creation Date	2014-11-27 17:25:01
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2014-11-27 17:25:01
Document Title	Microsoft Word - CL-120_manual_1112_2014
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Jelly

Product Specification
CL-120
IEEE802.11 a/n 3T3R PCIe Module
Version: 1.0
Date: OCT,15,2014
Release History
DATE
REV
2014/10/15
1.0
Description of Change
Initial release
CL-120
IEEE802.11a/n 3T3R PCIe Module
1. Introduction
CL-120
is
an
integrated
MAC/Baseband/Radio
with
the
pcie
Celeno
CLR260
interface.
single-chip
CL-120
fully
5GHz
complies
IEEE802.11a/n
with
IEEE802.11n
3T3R
and
IEEE802.11a/n feature rich wireless connectivity at high standards, delivers reliable, cost-effective,
throughput from an extended distance.
2. Features
Interoperable with IEEE802.11a/n WLAN.
Reverse direction grant data flow and frame aggregation.
Support 20MHz and 40MHZ Bandwidth PHY Rate max 450Mbps
operations. Wireless multimedia enhancements quality of service support
(QoS). Legacy and high throughput modes.
Multiple BSSID support.
WEP 64/128, WPA, WPA2, TKIP, and AES soft war e
encryption. PCIe Interface compliant.
Low power with advanced power management.
Operating systems – Windows XP 32/64,Vista 32/64, Linux, Macintosh.
3. General Specifications
Product Specification
Model Name
WLAN Standard
Host interface
CL-120
IEEE 802.11a/n, 3T3R
PCIe compatible Major Chipset Celeno CLR260
Dimensions
Minimum
Length
Width
Antenna Connector
Operating Condition
Voltage
Temperature
Storage temperature
Humidity Non-Operating
Typical
Maximum
51
31
Unit
mm
mm
3 Path ipex connector
DC
Minimum
3.3
-10
-20
Typical
3.3
Maximum
70
70
80
Unit
°C
°C
Electrical Specification
Frequency Range
Modulation
Data Rate
802.11b CCK Mode
802.11a OFDM Mode
802.11n HT20 Mode GI 800ns
802.11n HT20 Mode GI 400ns
802.11n HT40 Mode GI 800ns
802.11n HT40 Mode GI 400ns
Output Tx power
Rx
Sensitivity
Security
5180 - 5825
BPSK, QPSK, 16QAM, 64QAM, DBPSK, DQPSK, and CCK
xx Mbps
54, 48, 36, 24, 18, 12, 9, 6 Mbps
6.5 ~195 Mbps MCS 0 ~ MCS 23
7.2 ~216 Mbps MCS 0 ~ MCS 23
13.5 ~ 405Mbps MCS 0 ~ MCS 23
15 ~ 450Mbps MCS 0 ~ MCS 23
5 GHz LOW Band 16.5dbm +/-1.5dbm
5 GHz Hi
Band 17dbm +/-1.5dbm
5 GHz a/n mcs7 < -68dbm
WEP 64/128, WPA, WPA2, TKIP, and AES software encryption
Operating System Compatibility
Windows XP 32/64
Windows Vista 32/64
Windows 7 32/64
Linux Ubuntu
4. Mechanical Dimensions
5. CL-120 PCIe module installation
(1) Check main board quality and make sure the connector if soldered right.
(2) Get the CL‐120, and plug into the connector.
(3) Screw to fix the module
(4) Assemble the antenna
(5) Connect to a Wireless Network via a Wireless Network Router or Access Point
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This module is intended for OEM integrator.
The OEM integrator is still responsible for the FCC compliance requirement of the end product,
which integrates this module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment
authorizations (e.g. Verification , Doc) of the host device to be addressed by the
integrator/manufacturer.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to
be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment
can be satisfied. The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate this equipment.
The FCC part 15.19 statement below has to also be available in the manual: This device
complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
S4A50-0100-CL-01".

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Jelly
Create Date                     : 2014:11:27 17:25:01+08:00
Modify Date                     : 2014:11:27 17:25:01+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - CL-120_manual_1112_2014
Creator                         : Jelly
Document ID                     : uuid:04d5ba8b-ec46-4fcc-b29c-a7537c929498
Instance ID                     : uuid:9d238b3f-abd9-4d78-850f-36820addd4a4
Page Count                      : 6

EXIF Metadata provided by EXIF.tools