Enttec Wings Manual Revb User Rev B

User Manual: Enttec Wings Manual Revb Wings_Manual_revB revb wings

Open the PDF directly: View PDF .
Page Count: 4

Quick Start Manual

MANUAL-WING (NC)

For latest version visit:

www.enttec.com

1

ID: 210583

Box Contents

• ENTTEC Wing (70031, 70032 or 70033)

• 7V Power supply (79111)

• Country specific plug for power supply

• Cat5 patch cable (79102)

• Default IP address Label

• This user manual

Note: The user manual for all ENTTEC Wings is the same.

Please refer to the section relating to that specific product.

Introduction

Each ENTTEC Wing supports two modes, and can only one

mode can be active at a single time:

 ENTTEC Mode: Default mode, and is supported by

software such as D-PRO and Lightfactory.

 Art-Net Mode: Each key can be mapped to an Art-

Net channel and used as required.

Other software programs might support ENTTEC wings,

and their operation as it relates to those software titles will

be explained in full by those vendors.

After, un-packing the unit from the box, on the rear panel,

you will find:

• RJ45 Ethercon connector for a 10Base-T Ethernet

connection

• Status Led indicating if the device is powered up

and running

• Activity Led indicating the presence of packets on

the network

• Link led indicating the presence of an Ethernet

connection

• 7V DC power connector

The unit has no power switch and can be left on continuously.

Shortcut Wing Features

• Ethernet Interface

• 60 High quality Cherry MX Keys

• 2 Digit 7 Segment LED display

• PAGE UP & PAGE DOWN Keys

• Upgradeable firmware (using web-interface)

Playback Wing Features

• Ethernet Interface

• 40 High quality Cherry MX Keys

• 10 High Quality 60mm Faders

• 2 Digit 7 Segment LED display

• PAGE UP & PAGE DOWN Keys

• Large GO & BACK Keys

• Upgradeable firmware (using web-interface)

Program Wing Features

• Ethernet Interface

• 62 High quality Cherry MX Keys

◦ PAGE UP & PAGE DOWN Keys for Encoder

◦ 9 Window Keys

Quick Start Manual

MANUAL-WING (NC)

For latest version visit:

www.enttec.com

2

ID: 210583

◦ 25 Operational & Function Keys

◦ 19 Key Numeric Keypad

◦ 4 Arrow Keys and Backspace

• 3 Rotary Encoders

• 4 line 20 character LCD Display

• Upgradeable firmware (using web-interface)

Safety

 Do not expose the ENTTEC Wing to rain or

moisture, doing this will void the warranty

 Do not remove the cover, there are no serviceable

parts inside

 This unit is intended for indoor use only

Basic Setup

 Connect the ENTTEC Wing to your network using

the supplied or similar cat5 cable.

 Power up the Wing, the status and link LED should

light up, and activity led should blink – indicating

healthy network connection.

 ENTTEC Wing is factory configured with a Static IP

address (as mentioned on label/packaging).

 Further changes to the configuration/settings can

be made either using the web-interface, and/or

using NMU App on Windows and OSX.

 Keep the Wing in ENTTEC mode, to use with

supported software titles.

 The Wing should now be available to use in the

supported software window. (For more details,

please refer to the documentation of the relevant

software).

 Key press and/or Fader movements should be

mapped to your software, once it’s configured

properly.

Web Interface

Using the web interface, one can change the network

settings on the Wing and upgrade the firmware on the unit.

The web interface is accessible from any modern web

browser, by entering the IP address of the Wing.

Home: The Home page displays the Wing related information

(Name, Type, Firmware) and the current network settings. For

a quick reference an image of the Wing is shown at the

bottom. (Playback Wing shown in the picture above)

Settings: Change Network Settings – enable DHCP or

manually change the IP address as needed. Wing Mode can

also be changed here. If Art-Net mode is enabled, please use

NMU to configure the Wing further.

Art-Net send mode can be used to specify where the Wing

should send all Art-Net messages. (Broadcast is default)

To update the firmware on the Wing, please use “Update

Firmware” page, and follow the steps given below.

Quick Start Manual

MANUAL-WING (NC)

For latest version visit:

www.enttec.com

3

ID: 210583

Firmware Update

From this page you can update the latest firmware of the

ENTTEC Wing (firmware file is available at

enttec.com/wing). All 3 types of Wing use the same

firmware file.

Choose or browse the firmware file (as per your browser)

and click on Update firmware to start the process.

The update progress is shown in real-time, and will take a

few seconds for the update to complete.

When the update is complete, the page will refresh and you

will be taken to the home page – where you can verify the

firmware version. If the update fails for any reason, please

try the same process again.

Since, ENTTEC Wing will reboot after a firmware update,

please allow a few seconds for it to be refreshed in the

browser. Please wait until the update process is complete.

NMU

NMU (Node Management Utility) is a free Windows and

Mac application that is used to manage compatible

ENTTEC DMX over Ethernet nodes.

1. Download NMU from: enttec.com/nmu

2. Ensure that your ENTTEC Wing is hooked up physically by

Ethernet cable, to your network.

3. Open NMU. If prompted with multiple networks, select the

correct network. (Identified by the IP address of your com-

puter on that network)

4. Press the Discovery button, and wait till NMU finds all sup-

ported ENTTEC devices on your network. Select the Wing and

click Configure..

Art-Net Mode: Playback Wing

Quick Start Manual

MANUAL-WING (NC)

For latest version visit:

www.enttec.com

4

ID: 210583

You will need to select the Subnet and Universe from the

appropriate pulldowns in the Art-Net mode, which will tell

the Wing which Art-Net universe of the 255 possible

choices to use for the information it generates.

You can assign a total of 50 addresses to the 10 sliders and

the 40 buttons. The buttons have the option to be set for

Toggle or Flash, on a per button basis.

AUTOFILL: The Auto Fill button will return the assignments

to the default configuration, shown above.

SET CONFIG TO WING: Saves the changed configuration

to the Wing.

PAGE UP/DN: In addition to the 50 you have selected on

the main screen, you have access to up to 450 other DMX

addresses in the same Art- Net universe by pressing Page

Up and Page Down buttons on the Wing.

In the example shown above, on Page 2, the sliders would

correspond to channels 51-60.

EXCEEDING CHANNEL 512: Starting at higher than 62,

you may run out of room on page 10 or even before. Such

an arrangement would simply mean that on that page the

button or slider does nothing.

Supported Software

ENTTEC Wings are supported by various software titles.

Please refer to the respective software user-manual or

online guide for more details on what functions are

supported, and how to setup the Wings:

• D-PRO User Manual

enttec.com/pdf/manuals/70571.pdf

• LightFactory User Guide

LightFactory2_User_Guide.pdf

• FreeStyler

www.freestylerdmx.be

• QLC+

qlcplus.sourceforge.net

Wing Specifications

Due to continuous improvements and innovations of all

ENTTEC products, specifications and features are subject to

change without notice.

Item

Value

Power Requirements

7-9V DC

Weight

6.6 lbs / 3.0 Kg

Length

13.4” / 340mm

Width

9.45” / 240mm

Height

1.26” / 32mm

Op Environment

0°-50°C

Connectors

1x RJ45 Ethercon connector

Ordering Information

The ENTTEC Wings and compatible products can be ordered

from our website or through your ENTTEC dealer.

PN

Description

70031

Shortcut Wing

70032

Playback Wing

70033

Program Wing

70573

D-PRO 2U

70305

Open DMX Ethernet (ODE)

ENTTEC PTY LTD ENTTEC AMERICAS

17/5 Samantha Court 604A Cornerstone Ct.

Knoxfield Victoria 3180 Hillsborough NC 27278

Australia USA

Tel: +61 3 9763 5755 Tel-Fax: (888) 454-5922

Fax: +61 3 9763 5688

Email: sales@enttec.com

Website: www.enttec.com