Enttec Wings Manual Revb User Rev B
2017-06-20
User Manual: Enttec Wings Manual Revb Wings_Manual_revB revb wings
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Quick Start Manual MANUAL-WING (NC) For latest version visit: www.enttec.com Box Contents • • Link led indicating the presence of an Ethernet connection 7V DC power connector • ENTTEC Wing (70031, 70032 or 70033) • 7V Power supply (79111) The unit has no power switch and can be left on continuously. • Country specific plug for power supply Shortcut Wing Features • Cat5 patch cable (79102) • Default IP address Label • This user manual Note: The user manual for all ENTTEC Wings is the same. Please refer to the section relating to that specific product. Introduction Each ENTTEC Wing supports two modes, and can only one mode can be active at a single time: 60 High quality Cherry MX Keys • 2 Digit 7 Segment LED display • PAGE UP & PAGE DOWN Keys • Upgradeable firmware (using web-interface) Playback Wing Features ENTTEC Mode: Default mode, and is supported by • 40 High quality Cherry MX Keys software such as D-PRO and Lightfactory. • 10 High Quality 60mm Faders • 2 Digit 7 Segment LED display • PAGE UP & PAGE DOWN Keys • Large GO & BACK Keys • Upgradeable firmware (using web-interface) Art-Net Mode: Each key can be mapped to an Art- After, un-packing the unit from the box, on the rear panel, you will find: • • Ethernet Interface Other software programs might support ENTTEC wings, and their operation as it relates to those software titles will be explained in full by those vendors. • Ethernet Interface • Net channel and used as required. • • RJ45 Ethercon connector for a 10Base-T Ethernet connection Status Led indicating if the device is powered up and running Activity Led indicating the presence of packets on the network Program Wing Features • Ethernet Interface • 62 High quality Cherry MX Keys ◦ PAGE UP & PAGE DOWN Keys for Encoder ◦ 9 Window Keys 1 ID: 210583 Quick Start Manual MANUAL-WING (NC) For latest version visit: www.enttec.com ◦ 25 Operational & Function Keys ◦ 19 Key Numeric Keypad ◦ 4 Arrow Keys and Backspace • 3 Rotary Encoders • 4 line 20 character LCD Display • Upgradeable firmware (using web-interface) Safety Do not expose the ENTTEC Wing to rain or moisture, doing this will void the warranty Do not remove the cover, there are no serviceable parts inside This unit is intended for indoor use only Basic Setup Connect the ENTTEC Wing to your network using the supplied or similar cat5 cable. Power up the Wing, the status and link LED should light up, and activity led should blink – indicating healthy network connection. ENTTEC Wing is factory configured with a Static IP address (as mentioned on label/packaging). Further changes to the configuration/settings can be made either using the web-interface, and/or using NMU App on Windows and OSX. Keep the Wing in ENTTEC mode, to use with supported software titles. The Wing should now be available to use in the supported software window. (For more details, please refer to the documentation of the relevant software). Key press and/or Fader movements should be mapped to your software, once it’s configured properly. Home: The Home page displays the Wing related information (Name, Type, Firmware) and the current network settings. For a quick reference an image of the Wing is shown at the bottom. (Playback Wing shown in the picture above) Settings: Change Network Settings – enable DHCP or manually change the IP address as needed. Wing Mode can also be changed here. If Art-Net mode is enabled, please use NMU to configure the Wing further. Art-Net send mode can be used to specify where the Wing should send all Art-Net messages. (Broadcast is default) Web Interface Using the web interface, one can change the network settings on the Wing and upgrade the firmware on the unit. The web interface is accessible from any modern web browser, by entering the IP address of the Wing. To update the firmware on the Wing, please use “Update Firmware” page, and follow the steps given below. 2 ID: 210583 Quick Start Manual MANUAL-WING (NC) For latest version visit: www.enttec.com Firmware Update 1. Download NMU from: enttec.com/nmu 2. Ensure that your ENTTEC Wing is hooked up physically by Ethernet cable, to your network. 3. Open NMU. If prompted with multiple networks, select the correct network. (Identified by the IP address of your computer on that network) From this page you can update the latest firmware of the ENTTEC Wing (firmware file is available at enttec.com/wing). All 3 types of Wing use the same firmware file. Choose or browse the firmware file (as per your browser) and click on Update firmware to start the process. 4. Press the Discovery button, and wait till NMU finds all supported ENTTEC devices on your network. Select the Wing and click Configure.. The update progress is shown in real-time, and will take a few seconds for the update to complete. Art-Net Mode: Playback Wing When the update is complete, the page will refresh and you will be taken to the home page – where you can verify the firmware version. If the update fails for any reason, please try the same process again. Since, ENTTEC Wing will reboot after a firmware update, please allow a few seconds for it to be refreshed in the browser. Please wait until the update process is complete. NMU NMU (Node Management Utility) is a free Windows and Mac application that is used to manage compatible ENTTEC DMX over Ethernet nodes. 3 ID: 210583 Quick Start Manual MANUAL-WING (NC) For latest version visit: www.enttec.com You will need to select the Subnet and Universe from the appropriate pulldowns in the Art-Net mode, which will tell the Wing which Art-Net universe of the 255 possible choices to use for the information it generates. You can assign a total of 50 addresses to the 10 sliders and the 40 buttons. The buttons have the option to be set for Toggle or Flash, on a per button basis. AUTOFILL: The Auto Fill button will return the assignments to the default configuration, shown above. SET CONFIG TO WING: Saves the changed configuration to the Wing. PAGE UP/DN: In addition to the 50 you have selected on the main screen, you have access to up to 450 other DMX addresses in the same Art- Net universe by pressing Page Up and Page Down buttons on the Wing. In the example shown above, on Page 2, the sliders would correspond to channels 51-60. EXCEEDING CHANNEL 512: Starting at higher than 62, you may run out of room on page 10 or even before. Such an arrangement would simply mean that on that page the button or slider does nothing. Supported Software ENTTEC Wings are supported by various software titles. Please refer to the respective software user-manual or online guide for more details on what functions are supported, and how to setup the Wings: • LightFactory User Guide LightFactory2_User_Guide.pdf • FreeStyler www.freestylerdmx.be • Due to continuous improvements and innovations of all ENTTEC products, specifications and features are subject to change without notice. Item Power Requirements Value 7-9V DC Weight 6.6 lbs / 3.0 Kg Length 13.4” / 340mm Width 9.45” / 240mm Height 1.26” / 32mm Op Environment 0°-50°C Connectors 1x RJ45 Ethercon connector Ordering Information The ENTTEC Wings and compatible products can be ordered from our website or through your ENTTEC dealer. PN 70031 Description Shortcut Wing 70032 Playback Wing 70033 Program Wing 70573 D-PRO 2U 70305 Open DMX Ethernet (ODE) D-PRO User Manual enttec.com/pdf/manuals/70571.pdf • Wing Specifications ENTTEC PTY LTD 17/5 Samantha Court Knoxfield Victoria 3180 Australia Tel: +61 3 9763 5755 Fax: +61 3 9763 5688 ENTTEC AMERICAS 604A Cornerstone Ct. Hillsborough NC 27278 USA Tel-Fax: (888) 454-5922 Email: sales@enttec.com Website: www.enttec.com QLC+ qlcplus.sourceforge.net 4 ID: 210583