Epson Advanced Projector Ceiling Mount With Precision Gear Installation Guide
2015-03-28
: Epson Epson-Advanced-Projector-Ceiling-Mount-With-Precision-Gear-Installation-Guide-665883 epson-advanced-projector-ceiling-mount-with-precision-gear-installation-guide-665883 epson pdf
Open the PDF directly: View PDF 
.
Page Count: 11
| Download | |
| Open PDF In Browser | View PDF |
Installation and Assembly:
ADVANCED PROJECTOR CEILING MOUNT WITH PRECISION GEAR
Model: ELPMBPRG, ELPMBPRG-B
ENG Compatible with:
ELPMBC01
ELPMBP01
ELPMBP02
ELPMBP03
Max UL Load Capacity:
50 lb (22.7 kg)
Manufactured by Peerless Industries, Inc.
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call
Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power. See suggested torque values where applicable within these instructions.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 5/16" bit for concrete surface
• 5/32" bit for wood joist
• 3/8" (10 mm) socket wrench
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Extension Column.............................................................................................................................................4
Installation To Wood Joist Ceilings..........................................................................................................................................5
Installation to Concrete Ceilings..............................................................................................................................................6
Installing Plates to Projector ...................................................................................................................................................7
Installing Connection Block to Projector Mount Assembly......................................................................................................9
Cable Management.............................................................................................................................................................. 10
Projector Alignment...............................................................................................................................................................11
Accessories and Warranty Information................................................................................................................................. 12
Visit the Peerless Web Site at www.peerless-av.com
2 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Before you start check the parts list to ensure all of the parts shown are included.
Parts List
Description
projector mount assembly
adapter plate
dedicated adapter plate
M4 x 20 mm socket pin serrated washer head screw
#10-32 x 3/8" socket pin serrated washer head screw
3/8" spacer
M4 x 6 mm socket pin serrated washer head screw
concrete anchor
10-32 x 1/4" socket pin screw with lock
4 mm security allen wrench
washer
#14 x 2.5" wood screw
2 mm security allen wrench
#10 flat washer
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Qty
1
1
1
4
2
4
6
2
1
1
2
2
1
4
ELPMBPRG
Part #
580-2300
056-2065
055-2871
510-2163
520-2151
590-2150
510-2059
590-0320
520-2196
560-9646
540-2078
5S1-015-C04
560-1097
540-9442
ELPMBPRG-B
Part #
580-1300
056-1065
055-1871
510-1061
520-1151
590-1150
510-1059
590-0320
520-1196
560-9646
540-1078
5S1-015-C03
560-1097
540-9400
NOTE: Actual parts may appear slightly different than illustrated.
A
D
E
B
F
C
G
I
H
L
J
K
Visit the Peerless Web Site at www.peerless-av.com
M
3 of 11
N
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Installation to Extension Column
1
NOTE: Refer to accompanying instructions for ELPMBP01, ELPMBP02, ELPMBP03 or CMJ and ACC Series
Ceiling Mounts (sold separately) for installing these models to ceiling.
Screw projector mount assembly (A) onto extension column as shown in figure 1.1.
Use 4 mm allen wrench (J) to tighten swivel stop screw.
NOTE: Swivel stop screw is used to jam against threads of extension column or flush mount tube to prevent any
excess movement of projector mount assembly (A) as shown in detail 1. Do not overtighten screw; overtightening
screw will damage threads making it difficult to separate products.
Skip to step 2.
Not Shown: UL Listed ELPMBP01, ELPMBP02, ELPMBP03 or UL
Listed CMJ and ACC Series Ceiling Mounts (Sold Separately).
SWIVEL STOP
SCREW
EXTENSION COLUMN
(UL Listed ELPMBC01 or UL Listed
EXT and ADJ Series)
(Sold Separately)
A
DETAIL 1
fig. 1.1
Visit the Peerless Web Site at www.peerless-av.com
4 of 11
A
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Installation To Wood Joist Ceilings
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening
can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through 5/8" thickness drywall or plaster into wood studs.
1
Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Make
sure that the mounting holes are in the center of the wood joist. Drill two 5/32" (4 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach projector mount assembly (A) with two #14 x 2.5" (6 mm x 65 mm) wood screws (L)
and two flat washers (K) as shown in figure 1.3 or figure 1.4 depending on joist orientation.
NOTE: Mounting slots on projector mount assembly allow for 30° (±15°) of swivel adjustment before fully securing
wood screws.
Tighten wood screws (L) using 3/8" (10 mm) socket or open end wrench or phillips screwdriver until projector
mount assembly (A) is firmly attached.
Skip to step 2.
WOOD JOIST
WOOD JOIST
A
A
K
K
L
L
fig. 1.4
fig. 1.3
Visit the Peerless Web Site at www.peerless-av.com
5 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Installation to Concrete Ceilings
WARNING
• Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material.
1
Place projector mount assembly (A) on ceiling as a
template and mark the center of the two mounting
holes. Drill two 5/16" (8 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach projector mount
assembly (A) using two concrete anchors (H), two
flat washers (K), and two #14 x 2.5" wood screws (L)
as shown in Illustration A and 1, 2 and 3).
NOTE: Mounting slots on projector mount assembly
allow for 30° (±15°) of swivel adjustment before fully
securing wood screws.
Tighten wood screws (L) using 3/8" (10 mm) socket
or open end wrench or phillips screwdriver until
projector mount assembly (A) is firmly attached.
1
concrete
surface
H
Drill holes and insert anchors (H).
A
2
L K
H
Place plate (A) over anchors (H) and secure with screws (L).
3
WARNING
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly
reducing their holding power.
Tighten all fasteners.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
CONCRETE CEILING
• Always attach concrete anchors directly to loadbearing concrete.
CUTAWAY VIEW
• Never attach concrete anchors to concrete covered
with plaster, drywall, or other finishing material.
INCORRECT
concrete
A
plaster/
dry wall
CORRECT
A
H
concrete
plaster/
dry wall
A
K
L
Illustration A
Visit the Peerless Web Site at www.peerless-av.com
6 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Installing Plates to Projector
CAUTION
• All spacers shall be used where indicated. Not using spacers can cause damage to projector.
• It is the responsibility of the installer to ensure that the projector is properly ventilated.
NOTE: For all PowerLite® models, the manufacturer's product weight must be reviewed to ensure that the weight does not
exceed 50 lbs.
Adapter Plate: PowerLite 92, 93, 95, 96W, 905, 915W, 1835, 410W, 1750, 1760W, 1770W, 1775W,
1830, 1915, 1925W, S17, X17, W17, 97, 98, 99W, 955W, 965
2
Use adapter plate (B) as shown.
B
2-Plate Horizontal Configuration:
PowerLite Pro G5450WNL, G5200WNL, G5650WNL, G5350NL, G5150NL, G5550NL, G5750WNL, G5950NL
G5000, 4100, 4200W, 4300, 6110i
Attach adapter plate (B) to dedicated adapter plate (C) using six M4 x 6 mm socket pin screws (G).
2
G
B
C
Visit the Peerless Web Site at www.peerless-av.com
7 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
2
NOTE: Shoulder indicates back of adapter plate (B)
Flip projector upside down. Find your projector model from the hole patterns listed below. Using the holes indicated
on the corresponding hole pattern diagram, attach adapter plate (B) to projector using the appropriate number of
M4 x 20 mm socket pin serrated washer head screws (D), #10 flat washers (N), and spacers (F).
NOTE: Retaining spacers go between adapter plate and projector.
N
D
B
C
NOTE: SHOULDER
INDICATES THE BACK OF
ADAPTER PLATE (B)
F
FRONT
Hole Patterns
A. PowerLite 92, 93, 95, 96W, 905,
915W, 1835, 410W, 1830, 1915,
1925W, S17, X17, W17, 97, 98,
99W, 955W, 965
C. PowerLite Pro G5450WNL,
G5200WNL, G5650WNL,
G5350NL, G5150NL, G5550NL,
G5750WNL, G5950NL G5000,
4100, 4200W, 4300,
B. PowerLite 6110i
FRONT
FRONT
FRONT
D. PowerLite 1750, 1760W, 1770W, 1775W
D
FRONT
Attach adapter plate (B) to
projector using the three M4 x 20
mm socket pin serrated washer
head screws (D) and spacers (F),
and one #10 flat washer (N).
NOTE: Retaining spacers go
between adapter plate and
projector.
Visit the Peerless Web Site at www.peerless-av.com
8 of 11
N
FRONT
B
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Installing Connection Block to Projector Mount Assembly
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the projector.
3
Slide connection block with projector into projector mount assembly (A) as shown. Tighten captive screw to secure
projector to projector mount assembly (A).
A
CONNECTION BLOCK
CAPTIVE
SCREW
4
IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (I) through projector mount
assembly (A) and into connection block as shown.
I
Visit the Peerless Web Site at www.peerless-av.com
9 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Projector Alignment
5
To adjust yaw (swivel) for extension column installation: Loosen screw on projector mount assembly (A)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn
by hand for easy adjustment.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for
easy adjustment.
+/- 10°
Loosen screw, make adjustment, retighten screw.
4mm wrench
3/8"
(10mm)
4mm wrench
4mm wrench
Loosen screw, make adjustment, retighten screw.
Loosen screw, make adjustment, retighten screw.
+15°
-20°
+/- 5°
Visit the Peerless Web Site at www.peerless-av.com
10 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Cable Management
To make an opening to route cables through
6 projector mount assembly, adjust projector mount
fig. 6.1
CABLES WITH COMBINATION
OF VGA CONNECTOR
AND RCA PLUGS
assembly to full upward tilt position and maximum
left or right roll position by turning knobs for
adjustments as shown in step 5.
BEND WIRES OF RCA
PLUGS IN OPPOSITE
DIRECTION
Route cables through top of extension column as
shown.
NOTE: A method for assisting cables through
extension column may be required (example: string
tied to connector to help pull through extension
column).
Route cables through projector mount assembly as
shown and connect to projector.
ROUTE
CONNECTOR
THROUGH
FIRST
MAXIMUM DIMENSIONS
EXTENSION COLUMN
WILL ALLOW
HEIGHT DIMENSION
WILL VARY DEPENDING
ON WIDTH DIMENSION
MAXIMUM
WIDTH
1-9/16"
(40 mm)
DO NOT
CRIMP
WIRES
Visit the Peerless Web Site at www.peerless-av.com
11 of 11
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
For Technical Support Contact Peerless Mounts at 1-800-865-2112
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1-702 Instance ID : uuid:1ab9b33b-4a7d-4072-8491-c12fa848fde7 Original Document ID : adobe:docid:indd:1cae4d15-b453-11de-aeb2-c29b10450e08 Document ID : xmp.id:223B8810C1A0E31192B6D962F4626AE3 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:213B8810C1A0E31192B6D962F4626AE3 Derived From Document ID : xmp.did:203B8810C1A0E31192B6D962F4626AE3 Derived From Original Document ID: adobe:docid:indd:1cae4d15-b453-11de-aeb2-c29b10450e08 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:02:28 15:44:51-06:00 Create Date : 2014:02:28 15:44:51-06:00 Modify Date : 2014:02:28 14:56:39-08:00 Metadata Date : 2014:02:28 14:56:39-08:00 Creator Tool : Adobe InDesign CS6 (Windows) Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 11 Page Layout : SinglePage Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools