Epson Advanced Projector Ceiling Mount With Precision Gear Installation Guide

2015-03-28

: Epson Epson-Advanced-Projector-Ceiling-Mount-With-Precision-Gear-Installation-Guide-665883 epson-advanced-projector-ceiling-mount-with-precision-gear-installation-guide-665883 epson pdf

Open the PDF directly: View PDF PDF.
Page Count: 11

Installation and Assembly:
Model: ELPMBPRG, ELPMBPRG-B
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Manufactured by Peerless Industries, Inc.
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
Max UL Load Capacity:
50 lb (22.7 kg)
ADVANCED PROJECTOR CEILING MOUNT WITH PRECISION GEAR
Compatible with:
ENG ELPMBC01
ELPMBP01
ELPMBP02
ELPMBP03
2 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Extension Column ............................................................................................................................................4
Installation To Wood Joist Ceilings .........................................................................................................................................5
Installation to Concrete Ceilings .............................................................................................................................................6
Installing Plates to Projector ..................................................................................................................................................7
Installing Connection Block to Projector Mount Assembly......................................................................................................9
Cable Management ............................................................................................................................................................. 10
Projector Alignment ..............................................................................................................................................................11
Accessories and Warranty Information ................................................................................................................................ 12
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
• drill
• 5/16"bitforconcretesurface
• 5/32"bitforwoodjoist
• 3/8"(10mm)socketwrench
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call
Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power. See suggested torque values where applicable within these instructions.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING
3 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
NOTE: Actual parts may appear slightly different than illustrated.
Before you start check the parts list to ensure all of the parts shown are included.
D
L
M
F G I
JK
BC
A
H
N
E
Parts List ELPMBPRG
Part #
ELPMBPRG-B
Part #Description Qty
Aprojector mount assembly 1 580-2300 580-1300
Badapter plate 1 056-2065 056-1065
Cdedicated adapter plate 1 055-2871 055-1871
DM4 x 20 mm socket pin serrated washer head screw 4 510-2163 510-1061
E#10-32x3/8"socketpinserratedwasherheadscrew 2 520-2151 520-1151
F3/8"spacer 4 590-2150 590-1150
GM4 x 6 mm socket pin serrated washer head screw 6 510-2059 510-1059
Hconcrete anchor 2 590-0320 590-0320
I10-32x1/4"socketpinscrewwithlock 1 520-2196 520-1196
J4 mm security allen wrench 1 560-9646 560-9646
Kwasher 2 540-2078 540-1078
L#14x2.5"woodscrew 2 5S1-015-C04 5S1-015-C03
M2 mm security allen wrench 1 560-1097 560-1097
N#10atwasher 4 540-9442 540-9400
4 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
NOTE: Refer to accompanying instructions for ELPMBP01, ELPMBP02, ELPMBP03 or CMJ and ACC Series
Ceiling Mounts (sold separately) for installing these models to ceiling.
Screw projector mount assembly (A)ontoextensioncolumnasshowningure1.1.
Use 4 mm allen wrench (J) to tighten swivel stop screw.
NOTE: Swivelstopscrewisusedtojamagainstthreadsofextensioncolumnorushmounttubetopreventany
excess movement of projector mount assembly (A) as shown in detail 1. Do not overtighten screw; overtightening
screwwilldamagethreadsmakingitdifculttoseparateproducts.
Skip to step 2.
1
Installation to Extension Column
SWIVEL STOP
SCREW
DETAIL 1
A
g. 1.1
A
EXTENSION COLUMN
(UL Listed ELPMBC01 or UL Listed
EXT and ADJ Series)
(Sold Separately)
Not Shown: UL Listed ELPMBP01, ELPMBP02, ELPMBP03 or UL
Listed CMJ and ACC Series Ceiling Mounts (Sold Separately).
5 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Make
surethatthemountingholesareinthecenterofthewoodjoist.Drilltwo5/32"(4mm)dia.holestoaminimum
depthof2.5"(64mm).Attachprojectormountassembly(A)withtwo#14x2.5"(6mmx65mm)woodscrews(L)
andtwoatwashers(K)asshowningure1.3orgure1.4dependingonjoistorientation.
NOTE: Mounting slots on projector mount assembly allow for 30° (±15°) of swivel adjustment before fully securing
wood screws.
Tighten wood screws (L)using3/8"(10mm)socketoropenendwrenchorphillipsscrewdriveruntilprojector
mount assembly (A)isrmlyattached.
Skip to step 2.
1
Installation To Wood Joist Ceilings
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tightenwoodscrewssothatprojectormountassemblyisrmlyattached,butdonotovertighten.Overtightening
can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthrough5/8"thicknessdrywallorplasterintowoodstuds.
WARNING
LL
A
WOOD JOIST
KK
WOOD JOIST
A
g. 1.3 g. 1.4
6 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
Place projector mount assembly (A) on ceiling as a
template and mark the center of the two mounting
holes.Drilltwo5/16"(8mm)dia.holestoaminimum
depthof2.5"(64mm).Attachprojectormount
assembly (A) using two concrete anchors (H), two
atwashers(K),andtwo#14x2.5"woodscrews(L)
as shown in Illustration A and 1, 2 and 3).
NOTE: Mounting slots on projector mount assembly
allow for 30° (±15°) of swivel adjustment before fully
securing wood screws.
Tighten wood screws (L)using3/8"(10mm)socket
or open end wrench or phillips screwdriver until
projector mount assembly (A)isrmlyattached.
Installation to Concrete Ceilings
1
Illustration A
H
L
K
A
CONCRETE CEILING
CUTAWAY VIEW
A
CORRECT
plaster/
dry wall
concrete
INCORRECT
plaster/
dry wall
concrete
A
• Always attach concrete anchors directly to load-
bearing concrete.
• Never attach concrete anchors to concrete covered
withplaster,drywall,orothernishingmaterial.
WARNING
• Tightenwoodscrewsrmly,butdonotovertighten.
Overtightening can damage the screws, greatly
reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
1
3
H
Drill holes and insert anchors (H).
Place plate (A) over anchors (H) and secure with screws (L).
Tighten all fasteners.
2
H
A
LK
concrete
surface
• Neverattachconcreteexpansionanchorstoconcretecoveredwithplaster,drywall,orothernishingmaterial.
WARNING
7 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
2
Installing Plates to Projector
Attach adapter plate (B) to dedicated adapter plate (C) using six M4 x 6 mm socket pin screws (G).
G
B
C
2
• All spacers shall be used where indicated. Not using spacers can cause damage to projector.
• It is the responsibility of the installer to ensure that the projector is properly ventilated.
CAUTION
NOTE: For all PowerLite® models, the manufacturer's product weight must be reviewed to ensure that the weight does not
exceed 50 lbs.
B
Adapter Plate: PowerLite 92, 93, 95, 96W, 905, 915W, 1835, 410W, 1750, 1760W, 1770W, 1775W,
1830, 1915, 1925W, S17, X17, W17, 97, 98, 99W, 955W, 965
2-Plate Horizontal Conguration:
PowerLite Pro G5450WNL, G5200WNL, G5650WNL, G5350NL, G5150NL, G5550NL, G5750WNL, G5950NL
G5000, 4100, 4200W, 4300, 6110i
Use adapter plate (B) as shown.
8 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
B. PowerLite 6110i
Hole Patterns
A. PowerLite 92, 93, 95, 96W, 905,
915W, 1835, 410W, 1830, 1915,
1925W, S17, X17, W17, 97, 98,
99W, 955W, 965
FRONT FRONT FRONT
D. PowerLite 1750, 1760W, 1770W, 1775W
FRONT
Attach adapter plate (B) to
projector using the three M4 x 20
mm socket pin serrated washer
head screws (D) and spacers (F),
andone#10atwasher(N).
NOTE: Retaining spacers go
between adapter plate and
projector.
D
N
B
FRONT
C. PowerLite Pro G5450WNL,
G5200WNL, G5650WNL,
G5350NL, G5150NL, G5550NL,
G5750WNL, G5950NL G5000,
4100, 4200W, 4300,
C
D
2
NOTE: SHOULDER
INDICATES THE BACK OF
ADAPTER PLATE (B)
FRONT
NOTE: Shoulder indicates back of adapter plate (B)
Flip projector upside down. Find your projector model from the hole patterns listed below. Using the holes indicated
on the corresponding hole pattern diagram, attach adapter plate (B) to projector using the appropriate number of
M4 x 20 mm socket pin serrated washer head screws (D),#10atwashers(N), and spacers (F).
NOTE: Retaining spacers go between adapter plate and projector.
F
B
N
9 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
Slide connection block with projector into projector mount assembly (A) as shown. Tighten captive screw to secure
projector to projector mount assembly (A).
IMPORTANT:Forsecurityinstallations,insertone#10-32x1/4"socketpinscrew(I) through projector mount
assembly (A) and into connection block as shown.
3
• Always use an assistant or mechanical lifting equipment to safely lift and position the projector.
WARNING
Installing Connection Block to Projector Mount Assembly
4
CONNECTION BLOCK
A
CAPTIVE
SCREW
I
10 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
To adjust yaw (swivel) for extension column installation: Loosen screw on projector mount assembly (A)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn
by hand for easy adjustment.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for
easy adjustment.
5
Projector Alignment
+/- 10°
3/8"
(10mm)
Loosen screw, make adjustment, retighten screw.
4mm wrench
+15°
-20°
+/- 5°
4mm wrench
4mm wrench Loosen screw, make adjustment, retighten screw.
Loosen screw, make adjustment, retighten screw.
11 of 11
Visit the Peerless Web Site at www.peerless-av.com For Technical Support Contact Peerless Mounts at 1-800-865-2112
ISSUED: 04-01-08 SHEET #: 055-9254-19 02-28-14
Cable Management
To make an opening to route cables through
projector mount assembly, adjust projector mount
assembly to full upward tilt position and maximum
left or right roll position by turning knobs for
adjustments as shown in step 5.
Route cables through top of extension column as
shown.
NOTE: A method for assisting cables through
extension column may be required (example: string
tied to connector to help pull through extension
column).
Route cables through projector mount assembly as
shown and connect to projector.
MAXIMUM
WIDTH
1-9/16"
(40 mm)
HEIGHT DIMENSION
WILL VARY DEPENDING
ON WIDTH DIMENSION
DO NOT
CRIMP
WIRES
BEND WIRES OF RCA
PLUGS IN OPPOSITE
DIRECTION
MAXIMUM DIMENSIONS
EXTENSION COLUMN
WILL ALLOW
ROUTE
CONNECTOR
THROUGH
FIRST
g. 6.1
CABLES WITH COMBINATION
OF VGA CONNECTOR
AND RCA PLUGS
6

Navigation menu