Epson Elpmbp01 Users Manual
Epson-Adjustable-Suspended-Ceiling-Channel-Kit-Installation-Guide-664863 epson-adjustable-suspended-ceiling-channel-kit-installation-guide-664863
ELPMBP01 mbp01_ig
ELPMBP01 to the manual bd0cc9c2-bff1-4f58-a4e7-11fc2eaaaebd
2015-01-23
: Epson Epson-Elpmbp01-Users-Manual-252117 epson-elpmbp01-users-manual-252117 epson pdf
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
Installation and Assembly:
Adjustable Suspended Ceiling Channel Kit
Model: ELPMBP01
R
This product is UL Listed. It must be
installed by a qualified professional
installer.
Maximum UL Load Capacity: 50 lb (22.6 kg)
Manufactured by Peerless Industries, Inc.
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your product until you have read and understood the instructions and warnings contained in this
Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care
at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power. See suggested torque values where applicable within these instructions.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• When installing or adjusting the ceiling mount, do not use adhesives, lubricants or oils to prevent the screws from
loosening. If you use adhesives, lubricants, or oils to prevent the screws from loosening, the casing may crack and the
projector may fall, causing serious injury and damage to the projector.
Tools Needed for Assembly
•
•
•
•
•
•
•
stud finder ("edge to edge" stud finder is recommended)
phillips screwdriver
hammer
wire cutters
drill
1/4" bit for concrete surface
5/32" bit for wood studs
Table of Contents
Parts List .............................................................................................................................................................................. 3
Installation to Suspended Ceiling .......................................................................................................................................... 4
Anchoring Ceiling Plate ......................................................................................................................................................... 5
Warranty Information ............................................................................................................................................................. 6
2 of 6
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 02-13-08 SHEET #: 128-9029-2 07-10-08
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Before you start check the parts list to insure all of the parts shown are included.
NOTE: You may not need all hardware provided.
Parts List
A
B
C
D
E
F
G
H
I
J
K
L
Description
ceiling tray
1/4"-20 x 3/8" screws
1/4"-20 nuts
allen wrench
escutcheon ring
turnbuckle
12 gauge x 20' (6.1m) tie wire (not shown)
eye bolt
concrete anchor
flush mount tube
M5 x 10 mm penta pin screw
M5 x 1" penta pin driver
Qty.Part #
1 055-0492
4 520-2015
4 530-9302
1 560-9706
1 1418-001A
4 560-9620
1 600-2008
5 580-0006
5 580-0005
1 1446-014
1 505-9010
1 520-9249
NOTE: Some parts may appear slightly different than illustrated.
A
E
B
I
D
C
J
F
H
K
L
3 of 6
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 02-13-08 SHEET #: 128-9029-2 07-10-08
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Installation to Suspended Ceiling
IMPORTANT PRE-ASSEMBLY
INFORMATION:
1
Ceiling Tray (A) is designed to fit
above a 24" (610 mm) x 24" (610
mm) section of a conventional
suspended ceiling system. It may
also be mounted above 24" x 48"
conventional suspended ceiling.
Ceiling runners (see DETAIL 2,
page 5) should have a “T” cross
section and a minimum height of
1.5" (38 mm).
For certain installations it may be
best to install ceiling anchors (step
5) before installing the ceiling tray
(step 1).
Place ceiling tray (A) in grid above 24" x 24" or 24" x 48" false ceiling tile
so that lip of ceiling tray (A) rests on ceiling runners as shown in figure 1.
Place in desired position and tighten knurled knobs until ceiling tray (A) is
securely attached to ceiling runners.
Slide collar mount plate to desired position. Using hole in collar mount
plate, mark false ceiling tile where hole will be cut. Slide collar mount plate
out of the way. Cut out 2.25" hole in false ceiling tile. Slide collar mount
plate back into position and tighten all carriage bolts and nylock nuts using
a 7/16" wrench.
COLLAR MOUNT PLATE
CARRIAGE BOLT
KNURLED KNOB
A
CEILING
RUNNER
NYLOCK NUT
For Flush Mounting Applications
2
For Extension Column Applications
2
From the top down, thread flush mount tube (J) down
through retaining collar in adjustable collar mount
plate.
Skip to step 3.
A
fig. 1
J
From the bottom up, thread extension column (not
included) up through retaining collar in adjustable
collar mount plate. Align notch in extension
column with hole in collar and fasten using M5 x
10 mm security screw (K) as shown in detail 1.
A
K
DETAIL 1
1 1/2" EXTENSION COLUMN
(SOLD SEPARATELY)
(UL LISTED EXT OR ADJ SERIES)
3
Snap escutcheon ring (E) around flush mount tube or extension column and slide up until flush with ceiling tile. Hook
turnbuckles (F) into ceiling tray (A) as shown in figure 2. Hook turnbuckles through ceiling tray (A) where indicated
by black rectangles in illustration below.
A
F
TOP VIEW - CEILING TRAY
Black rectangles show correct
positions for Turnbuckles.
fig. 2
4 of 6
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 02-13-08 SHEET #: 128-9029-2 07-10-08
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Anchoring Ceiling Plate
4
Cut tie wire (G) into four pieces of equal length. Insert wires through ends of turnbuckles and loop. Twist each wire
around itself at least six times.
Drill holes for four ceiling anchors (see "Various Anchoring Methods"). Position the holes so that when the tie
wires (G) are attached and taut will angle out at 15O.
Pull tie wires tight and loop though turnbuckles of the ceiling anchors (or truss). Again twist each wire around itself
at least six times.
When this step is complete, the weight of the ceiling tray should be supported by the tie wires.
NOTE: 20' (6.1 m) of tie wire (G) is provided. If space between the true ceiling and suspended ceiling is more than
36" (914 mm), additional wire (12 gauge annealed, steel, black) will be needed.
VARIOUS ANCHORING METHODS
Wood Joists or Beams
Drill 5/32" (4mm) dia.
holes 2" (51mm) deep.
Fully insert eye bolts (H).
Solid Concrete
Drill 1/4" (6 mm) dia. holes 1.5" (38 mm)
deep. Hammer in Concrete Anchor (I)
using Rawl #3250 setting tool
or equivalent.
H
Truss Ceiling
No anchor required. After
attaching tie wire to turnbuckle
loop upper end around ceiling
truss. Pull tie wire tight and
twist it around itself at least six
times.
I
15°
G
G
WARNING
G
• It is the responsibility of the installer to verify that the
ceiling to which the suspended ceiling kit is anchored
will safely support four times the combined weight of
all attached components (Projector Mount, Extension
Column, etc.) and equipment.
5
A
2"
Suspended Ceiling Kit installation is now complete.
After all components (Projector Mount, Extension
Column, etc.) and equipment have been attached,
tension the tie wires by adjusting turnbuckles (F).
CEILING
RUNNER
NOTE: Load must be carried by tie wires - not
suspended ceiling runners.
1.5"
KNOCK-OUTS ARE
PROVIDED FOR
ELECTRICAL OUTLET
BOXES AND ANTENNA
LEADS.
DETAIL 2
5 of 6
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 02-13-08 SHEET #: 128-9029-2 07-10-08
For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
LIMITED FIVE-YEAR WARRANTY
3HHUOHVV,QGXVWULHV,QFHVWDEOLVKHVDZDUUDQW\SHULRGRIÀYH\HDUVIRUSURGXFWVPDQXIDFWXUHGRUVXSSOLHGE\3HHUOHVV7KLVSHULRGFRPPHQFHVIURPWKHGDWH
RIVDOHRIWKHSURGXFWWRWKHRULJLQDOFRQVXPHUEXWZLOOLQQRFDVHODVWIRUPRUHWKDQVL[\HDUVDIWHUWKHGDWHRIWKHSURGXFWҋVPDQXIDFWXUH'XULQJWKHZDUUDQW\
SHULRGVXFKSURGXFWVZLOOEHIUHHIURPGHIHFWVLQPDWHULDODQGZRUNPDQVKLSSURYLGHGWKH\DUHLQVWDOOHGDQGXVHGLQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVHVWDEOLVKHGE\
3HHUOHVV,QGXVWULHV,QF6XEMHFWWRDSSOLFDEOHOHJDOUHTXLUHPHQWVGXULQJWKHZDUUDQW\SHULRG3HHUOHVVZLOOUHSDLURUUHSODFHRUUHIXQGWKHSXUFKDVHSULFHRIDQ\
VXFKSURGXFWZKLFKIDLOVWRFRQIRUPZLWKWKLVZDUUDQW\
$Q\RWKHUZDUUDQWLHVSUHVFULEHGE\WKHODZZKLFKPD\DSSO\ZLWKUHVSHFWWRVXFKSURGXFWVDOVRDUHOLPLWHGLQGXUDWLRQWRWKHZDUUDQW\SHULRGVSHFLÀHGLQWKLV/LPLWHG
)LYH
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : Yes
Encryption : Standard V1.2 (40-bit)
User Access : Print, Fill forms, Extract, Assemble, Print high-res
Page Mode : UseOutlines
XMP Toolkit : 3.1-702
Format : application/pdf
Title :
Creator : .
Description :
Create Date : 2008:08:06 17:50:52-05:00
Creator Tool : Adobe PageMaker 7.0
Modify Date : 2008:11:13 14:52:35-08:00
Metadata Date : 2008:11:13 14:52:35-08:00
Producer : Acrobat Distiller 8.0.0 (Windows)
Document ID : uuid:a5e57cf3-1388-4538-9b13-7a9b285394ae
Instance ID : uuid:ff560227-cbc6-4ebe-a62a-141f75c64954
Page Count : 6
Page Layout : SinglePage
Subject :
EXIF Metadata provided by EXIF.tools